Tallow
"Chris Carruth" <[email protected]> wrote in message
news:[email protected]...
> just finished bench...have two vises, front and end..what kind of
> oil/grease should I use?
>
Chris Carruth wrote:
> just finished bench...have two vises, front and end..what kind of oil/grease
> should I use?
>
>
I use paraffin dissolved in mineral spirits.
--
Gerald Ross
Cochran, GA
Yield to temptation, it may not pass
your way again. - L. Long
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
Chris Carruth wrote:
> just finished bench...have two vises, front and end..what kind of oil/grease
> should I use?
Same stuff you'd use for TS trunions and screw, something that won't
attract dust. White lube is popular and better than regular grease, but
still attracts too much dust, IMO. Graphite works well, but won't stay
on that long. Most end up using some sort of wax based mix. Teflon
mixes are good too. I've settled on using fish-wire lube (i.e., the
tool electicians use to fish wire through conduit) mixed with graphite.
H
On 2006-05-22, Chris Carruth <[email protected]> ranted thusly:
> just finished bench...have two vises, front and end..what kind of oil/grease
> should I use?
It's impossible to say without being able to see the bench. Post in
abpw. :)
er
--
email not valid
On Mon, 22 May 2006 03:40:04 GMT, "Chris Carruth"
<[email protected]> wrote:
>just finished bench...have two vises, front and end..what kind of oil/grease
>should I use?
>
I have been using my bench vise (Record) for over 15 years without any
lubrication and it operates just fine, no squeaks. I'd probably use
lithium grease if there was a problem with movement, same stuff
recommended for my tablesaw gears.
> just finished bench...have two vises, front and end..what kind of oil/grease
> should I use?
>
>
That was exactly my question last year, way too early, found an antique quick
action woodworker's vise in the backyard of a junk shop for $20, thrilled with
that! Although I didn't know so I didn't check for it, it had the original half
nut luckily.
As for lube for the lead screw, I thought of "grease" of course, asked in news
groups curious about old fashion petrolium based heavy axle grease and it
isn't made anymore, not that I can find anywhere. It's always one form or
another of modern tech lithium stinky stuff. What is axle grease? Regular old
grease, filtered and soaped crude oil.
However, motor oil and beeswax melted together to whatever viscosity you
want (more or less beeswax) done in a double boiler with a little turpentine
added to break it up for pastyness, should work well.
--
Alex - "newbie_neander" woodworker
cravdraa_at-yahoo_dot-com
not my site: http://www.e-sword.net/
"Gerald Ross" wrote...
> I use paraffin dissolved in mineral spirits.
Years ago I made a hot paraffin/turpentine mix and let it cool in an old
coffee can. Now when I need it, I just take the little copper glue pot out
of the hold-heat warmer, put in the coffee can, and heat and melt the wax
for easy application. Keeps the screws clean & easy to turn.
--
Timothy Juvenal
www.rude-tone.com/work.htm