I got this email from a friend. I don't have any experience but thought
someone here might know some tricks..
We had a bag of stuff sitting on our kitchen table and something leaked and
appears to have soaked the ink off the label onto the table. I didn't know
if you knew any tricks. We are going to try a commercial ink remover but
failing that the only thing I know to do is sand the whole table and
restain/seal it. Any other ideas?
Many thanks,
Russell
It would be a big help if you could identify what leaked .
I would start with a wet paper towel and see if any of the ink comes
up. It may take several applications.
If that does not work move up to the vinegar, alcohol, acetone etc
cleaners.
Try each with a cotton bud to test the stability of the finish.
In article <[email protected]>,
Russell Bennight <[email protected]> wrote:
>I got this email from a friend. I don't have any experience but thought
>someone here might know some tricks..
>
>We had a bag of stuff sitting on our kitchen table and something leaked and
>appears to have soaked the ink off the label onto the table. I didn't know
>if you knew any tricks. We are going to try a commercial ink remover but
>failing that the only thing I know to do is sand the whole table and
>restain/seal it. Any other ideas?
>
>Many thanks,
>Russell
>
>
One "obvious" comment -- 'whatever it was' that leaked is proven to
dissolve the ink in question. thus it _should_ be usable to take the
ink up _from_ the table.
That aside, a great deal depends on _what_ the pre-existing finish on
the table is. The trick is finding something that will dissolve the ink,
*without* dissolving whatever the finish is.
Without knowing what the finish is, and what type of ink is involved,
any specific product mentions are just a 'wild guess'. Be *sure* to
test anything on an 'inconspicuous' finished area _first_, to make sure
that it doesn't damage the finish. *then* see if it will take up the ink.
a partial list of things to try includes:
soap (e.g. Ivory, Dial, etc.) and water
dish detergent (e.g. Palmolive) and water
alcohol (If you don't have isopropyl on hand, cheap vodka can be used :)
ammonia
"Simple Green"
a citric-based cleaner -- e.g. "Orange Clean"
"Oxy-Clean"
"Goop"
As weird as this may sound, if the ink hasn't soaked into the pores of the
wood, try hairspray. It's an amazing ink remover and not hard on finishes.
"Russell Bennight" <[email protected]> wrote in message
news:[email protected]...
>I got this email from a friend. I don't have any experience but thought
> someone here might know some tricks..
>
> We had a bag of stuff sitting on our kitchen table and something leaked
> and
> appears to have soaked the ink off the label onto the table. I didn't know
> if you knew any tricks. We are going to try a commercial ink remover but
> failing that the only thing I know to do is sand the whole table and
> restain/seal it. Any other ideas?
>
> Many thanks,
> Russell
>
>
"Andy" <[email protected]> wrote in message
news:[email protected]...
> I'd try alcohol (ethanol or isopropyl rubbing) or acetone (nail-polish
> remover) but be sure to test them on the table's finish first - alcohol
> will soften/remove shellac, for instance, but tabletops probably
> shouldn't be finished in shellac to begin with.
Acetone is much more likely to pull up stuff with it. I'd be very careful
with it.
Bob
"D Steck" <[email protected]> wrote in message
news:[email protected]...
> As weird as this may sound, if the ink hasn't soaked into the pores of the
> wood, try hairspray. It's an amazing ink remover and not hard on
> finishes.
Hair spray works because it usually has alchohol in it. You could try
rubbing alchohol, but bve careful of clouding and try someplace not viseable
first.
Acetone, gasoline and bleach all come to mind as well... Then again, so
does fire, but you want to keep the table, right?
Regards,
Joe Agro, Jr.
(800) 871-5022
(908) 542-0244
http://www.AutoDrill.com
http://www.Multi-Drill.com
V8013-R