I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
with a riser as a larger bandsaw (17" and up) won't fit into my
workshop area. The biggest job I can foresee doing is resawing a 9-10"
piece of rosewood, cocobolo, or walnut.
There seems to be a wide range of motors out there for 14" bandsaws,
from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
resawing job?
[email protected] wrote:
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
My Grizzly 14" has a 3/4 hp motor. With a Wood Slicer blade from
Highland Hardware I have no trouble resawing anything.
On 1 Aug 2006 14:11:12 -0700, [email protected] wrote:
>I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
>with a riser as a larger bandsaw (17" and up) won't fit into my
>workshop area. The biggest job I can foresee doing is resawing a 9-10"
>piece of rosewood, cocobolo, or walnut.
>
>There seems to be a wide range of motors out there for 14" bandsaws,
>from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
>resawing job?
As in all wood working and tool buying, you have to separate need and want, then
ignore need and go for want.. *g*
My BS is a 3/4 hp with a riser, using 105" blades..
it does what I need it to, if I take my time and don't abuse the
blade/motor/wood..
So, it's all I "need"...
"want" is maybe a chevy v-8 or at least a 5 hp variable speed motor.. *g*
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
"Tim Taylor" <[email protected]> wrote in message
news:[email protected]...
>
> "Tom Gardner" <tom(nospam)@ohiobrush.com> wrote in message
> news:[email protected]...
>>
>> <[email protected]> wrote in message
>> news:[email protected]...
>>> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
>>> with a riser as a larger bandsaw (17" and up) won't fit into my
>>> workshop area. The biggest job I can foresee doing is resawing a 9-10"
>>> piece of rosewood, cocobolo, or walnut.
>>>
>>> There seems to be a wide range of motors out there for 14" bandsaws,
>>> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
>>> resawing job?
>>>
>>
>> 2 hp min. You won't regret it! It will run better and safer!
>>
> Safer??
You bet! Under powered tools are unpredictable when running at their
limits. It avoids binding, slow-down and such and the operator isn't
tempted to push on something harder or interrupt his thought and motion.
Think about it.
"Tim Taylor" <[email protected]> wrote in message
news:[email protected]...
>>> Safer??
>>
>> You bet! Under powered tools are unpredictable when running at their
>> limits. It avoids binding, slow-down and such and the operator isn't
>> tempted to push on something harder or interrupt his thought and motion.
>> Think about it.
>>
> Ok, I can see that from some peoples stand point, but if I hear any of my
> machines bogging down, I back off and don't push it. But then again,
> that's me, so I can see why you said safer. Sorry.
For my employees, I want the most predictable operation...and that leads to
predictable production. It seems tool life is extended too. Maybe 2 hp for
a little bandsaw seems overkill but I'd bet blades stay cooler and last
longer since there's less chance of binding and strain...just an opinion.
My stuff is all big production equipment so I'm just guessing in the
home-shop realm.
>> Safer??
>
> You bet! Under powered tools are unpredictable when running at their
> limits. It avoids binding, slow-down and such and the operator isn't
> tempted to push on something harder or interrupt his thought and motion.
> Think about it.
>
Ok, I can see that from some peoples stand point, but if I hear any of my
machines bogging down, I back off and don't push it. But then again, that's
me, so I can see why you said safer. Sorry.
"Tom Gardner" <tom(nospam)@ohiobrush.com> wrote in message
news:[email protected]...
>
> <[email protected]> wrote in message
> news:[email protected]...
>> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
>> with a riser as a larger bandsaw (17" and up) won't fit into my
>> workshop area. The biggest job I can foresee doing is resawing a 9-10"
>> piece of rosewood, cocobolo, or walnut.
>>
>> There seems to be a wide range of motors out there for 14" bandsaws,
>> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
>> resawing job?
>>
>
> 2 hp min. You won't regret it! It will run better and safer!
>
Safer??
In article <[email protected]>,
Tom Gardner <tom(nospam)@ohiobrush.com> wrote:
<...snipped...>
>
>For my employees, I want the most predictable operation...and that leads to
>predictable production. It seems tool life is extended too. Maybe 2 hp for
>a little bandsaw seems overkill but I'd bet blades stay cooler and last
>longer since there's less chance of binding and strain...just an opinion.
>My stuff is all big production equipment so I'm just guessing in the
>home-shop realm.
>
>
I won't argue that 2HP might benefit a 14" bandsaw, but the usuall
single belt drive setup on a bandsaw with an 1800 or 3600 rpm motor is
pushing its limits at 2HP. 1.5 hp motors seem to be more common
(especially used) and certainly less expensive for new ones.
--
Larry Wasserman Baltimore, Maryland
[email protected]
I purchased the American made 1 1/2 hp Delta X5, a riser block, heavier
spring, Kreg fence, magnetic light and mobile base just before I retired.
You know the works. At least to the level I can afford on my hobby budget
and the last bandsaw I'll purchase. It cuts almost effortlessly through
anything I need to saw. Great for resawing hardwood such as you mention,
cutting out bowl rounds from half logs for my lathe, etc. It's a pure joy
to use. Overkill? I don't know. All I can say is I don't regret it a bit..
This isn't an ad for Delta, however; I did have to get a new cord from them
after installing the riser block. Cord between motor and switch became too
short and wouldn't allow switch to reach to its mounting holes. Apparently,
factory worker stripped a little too much wire before connecting to switch.
<[email protected]> wrote in message
news:[email protected]...
> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
> with a riser as a larger bandsaw (17" and up) won't fit into my
> workshop area. The biggest job I can foresee doing is resawing a 9-10"
> piece of rosewood, cocobolo, or walnut.
>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
>
[email protected] wrote:
> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
> with a riser as a larger bandsaw (17" and up) won't fit into my
> workshop area. The biggest job I can foresee doing is resawing a 9-10"
> piece of rosewood, cocobolo, or walnut.
>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
>
I have a 14" bandsaw with a 3/4 HP motor. I often wish it had 1.5 HP.
One of these days I'll change the motor.
--
Jack Novak
Buffalo, NY - USA
[email protected]
(Remove -SPAM- to send email)
<[email protected]> wrote in message
news:[email protected]...
> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
> with a riser as a larger bandsaw (17" and up) won't fit into my
> workshop area. The biggest job I can foresee doing is resawing a 9-10"
> piece of rosewood, cocobolo, or walnut.
>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
>
2 hp min. You won't regret it! It will run better and safer!
<[email protected]> wrote in message
news:[email protected]...
> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
> with a riser as a larger bandsaw (17" and up) won't fit into my
> workshop area. The biggest job I can foresee doing is resawing a 9-10"
> piece of rosewood, cocobolo, or walnut.
>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
>
More is better but you can get by with 1. IMHO the more power the better
the cut also.
Concerning size, my 16" Laguna has a smaller foot print than my old 12"
Craftsman and is shorter than many 14" saws with riser blocks.
> [email protected] wrote:
>
> > There seems to be a wide range of motors out there for 14" bandsaws,
> > from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> > resawing job?
I can re-saw easily wiht 1.5 hp, but I dont have a riser block. 2 HP would
be better for that setup.
<[email protected]> wrote in message
news:[email protected]...
> I'm in the market for my first bandsaw. I'm limited to a 14" bandsaw
> with a riser as a larger bandsaw (17" and up) won't fit into my
> workshop area. The biggest job I can foresee doing is resawing a 9-10"
> piece of rosewood, cocobolo, or walnut.
>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
>
You are going to try to resaw that width of those trees with anything less
that 1 1/2 hp? Good luck.
Jim
[email protected] wrote:
> I'm in the market for my first bandsaw.
<snip>
> There seems to be a wide range of motors out there for 14" bandsaws,
> from 1/2 HP up to 1-1/2 HP. How big of a motor would I need for this
> resawing job?
How deep are your pockets?
Bigger is better when it comes to electric motors.
Lew