I have a compressor that is about 15 years old.
I remember back about 10years ago some guys telling me about something
that I should throw in the tank every 5 years to prevent rust and blow
out. I thought it was like a paint, not an oil... They told me it was
made for compressor tanks.
Anyone know what I am talking about and where to get it. I used to have
a compressor company a few miles from me... but they are gone... So I
don't even know where to get the stuff.
Mike Marlow wrote:
> "tiredofspam" <nospam.nospam.com> wrote in message
> news:[email protected]...
>
>>I have a compressor that is about 15 years old.
>>I remember back about 10years ago some guys telling me about something
>>that I should throw in the tank every 5 years to prevent rust and blow
>>out. I thought it was like a paint, not an oil... They told me it was
>>made for compressor tanks.
>>Anyone know what I am talking about and where to get it. I used to have
>>a compressor company a few miles from me... but they are gone... So I
>>don't even know where to get the stuff.
>
>
> Never heard of anything like that. I don't know that I'd be one of the
> first to jump on that train though, even if it was available. Most miracle
> cures like that aren't worth the powder to blow them to... well, you know.
> IMHO, you're better off simply draining your tank every week or so
> (depending on how much it gets used) or getting one of those automatic
> blowoffs from Harbor Freight for $10. They hook to the pressure line
> running to the pressure switch and run down to a valve that you install in
> place of your drain cock. Every time the compressor cycles it causes a
> small blowoff of air out the bottom of the tank and does a very good job of
> keeping water from building up in the tank.
I drain the tank almost every night. I put a lever ball valve on instead
of the petcock. I bought the auto drain kit, only to find out that my
compressor was so old that it didn't have the prerequisite black plastic
piping to the pressure sensor. Mine is mounted to the tank. The magic
isn't really magic... The guys were from the compressor company. Ever
use rustoleum on rusted metal?? It converts and protects. Other paints
won't adhere. So it isn't really magic... But this wasn't rustoleum...
BTW a tank that goes can easily go through cinder block and through dry
wall or wood like butter.
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
>
> I drain the tank almost every night. I put a lever ball valve on instead
> of the petcock. I bought the auto drain kit, only to find out that my
> compressor was so old that it didn't have the prerequisite black plastic
> piping to the pressure sensor. Mine is mounted to the tank.
Bummer. You could convert it if you really felt like it - just plumb a
newer style pressure switch in and then you can run the line to your drain.
But really, draining it daily ought to be about as good as it gets. I'm not
sure I'd do any more than that.
> The magic
> isn't really magic... The guys were from the compressor company. Ever
> use rustoleum on rusted metal?? It converts and protects. Other paints
> won't adhere. So it isn't really magic... But this wasn't rustoleum...
Well, Rustoleum doesn't really do any conversions - it's just a paint that
will adhere to rust. It attempts to seal in the rust rather than to convert
it. There are compounds out there that actually convert the rust - mostly
by the use of tannins to convert the iron oxide to iron tannate. There's
others that simply apply a heavy polymer coating to the metal thus sealing
out oxygen. Either type should have a good primer and top coat applied over
them, and many are quite picky about what type of top coat you can apply.
Neither will work on an oily surface though and the inside of your
compressor tank, if it's an oil filled compressor, assuredly has an oil film
on it. These chemicals do work to some degree, but they aren't as wonderful
as the advertisements would have you believe.
> BTW a tank that goes can easily go through cinder block and through dry
> wall or wood like butter.
Yup - it sure can, and it can separate into smaller shrapnel like pieces
too. Fortunately, they usually just develop a leak.
--
-Mike-
[email protected]
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
> BTW a tank that goes can easily go through cinder block and through dry
> wall or wood like butter.
We are fortunate that the most common mode of compressor tank failure is
pinhole rust through, so you know your tank has a problem instead of it
spontaneously exploding.
-j
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
> I have a compressor that is about 15 years old.
> I remember back about 10years ago some guys telling me about something
> that I should throw in the tank every 5 years to prevent rust and blow
> out. I thought it was like a paint, not an oil... They told me it was
> made for compressor tanks.
> Anyone know what I am talking about and where to get it. I used to have
> a compressor company a few miles from me... but they are gone... So I
> don't even know where to get the stuff.
Never heard of anything like that. I don't know that I'd be one of the
first to jump on that train though, even if it was available. Most miracle
cures like that aren't worth the powder to blow them to... well, you know.
IMHO, you're better off simply draining your tank every week or so
(depending on how much it gets used) or getting one of those automatic
blowoffs from Harbor Freight for $10. They hook to the pressure line
running to the pressure switch and run down to a valve that you install in
place of your drain cock. Every time the compressor cycles it causes a
small blowoff of air out the bottom of the tank and does a very good job of
keeping water from building up in the tank.
--
-Mike-
[email protected]