Has anyone used the Jorgensen 1650 hold down clamp on their bench? The
mount through a 3/4" dog hole.
Coastal tools has them in packs of two for $10.95 (less than $6.00 apiece).
At this price, if they work at all, they seem worthwhile.
Here's the link to the clamps I am talking about: http://tinyurl.com/74sf2
Bob Davis
"BillyBob" <[email protected]> wrote in message
news:[email protected]...
>
> "Edwin Pawlowski" <[email protected]> wrote in message
> news:RrGke.15$4b.10@trndny07...
>
> > They look pretty handy and not much of a $ risk. Only problem I see is
> > getting to the underside of the bench to mount them if you have drawers
> and
> > stuff in the way.
>
> Thanks for the response Edwin. I may buy just to see what they are like.
> I've intentionally relocated the drawer on my work bench to allow easy
> access to the under side of the table. I've got a couple of bench dogs
and
> a wonder dog and use them a lot since I put a bunch of holes in my bench.
> But I seem to come up with occasions every other day where a nice hold
down
> would be very useful. I really like the Veritas solution but my budget
> doesn't have them as a priority yet. Up to know F-clamps have worked but
> they are not nearly as convenient or as flexible as a hold down.
>
> Bob
>
I've used 'em, and they're not going to hold even close to the Veritas, or
even the wedge type Roy Underhill uses. The use of the word "flexible"
suits how they hold fairly well.
"Andy Dingley" <[email protected]> wrote in message
news:[email protected]...
> They're very quick and easy to use, but they're so sprngy they don't
> allow much clamping force. They're useful when routing, but no use for
> hand tools.
>
> They also need to be shimmed to be near horizontal or their clamping
> suffers. The teeth on the end of the jaw are pretty sharp and damaging
> too.
Thanks, Andy. I think I'm going to pass on them. I've grown to appreciate
really good acting clamps. Nothing adds more to the pleasure of
woodworking, in my opinion.
Bob
"Edwin Pawlowski" <[email protected]> wrote in message
news:RrGke.15$4b.10@trndny07...
> They look pretty handy and not much of a $ risk. Only problem I see is
> getting to the underside of the bench to mount them if you have drawers
and
> stuff in the way.
Thanks for the response Edwin. I may buy just to see what they are like.
I've intentionally relocated the drawer on my work bench to allow easy
access to the under side of the table. I've got a couple of bench dogs and
a wonder dog and use them a lot since I put a bunch of holes in my bench.
But I seem to come up with occasions every other day where a nice hold down
would be very useful. I really like the Veritas solution but my budget
doesn't have them as a priority yet. Up to know F-clamps have worked but
they are not nearly as convenient or as flexible as a hold down.
Bob
"George" <george@least> wrote in message
news:[email protected]...
> I've used 'em, and they're not going to hold even close to the Veritas, or
> even the wedge type Roy Underhill uses. The use of the word "flexible"
> suits how they hold fairly well.
Thanks, George. I went to a local dealer and had a hands-on look at the
Veritas hold down. Now I understand why it costs what it does. Its quite a
piece of machinery. I brought one home to give it a whirl. I'm not sure
about the shaft on it. The literature does not mention it and its not
obvious from the pictures. The shaft has a very shallow and sharp thread
running the full length. This gives it some gripping power in the dog hole.
However, it may also wear out your dog hole in a hurry. I tried it on a
maple work bench at the dealer. Little tiny wood shavings came out of the
hole when I pulled the clamp back out. Hmmm, but I bought it anyway to see
how it works on my bench. I'm sure I can return it if I decide to, within a
couple of days.
Bob
"BillyBob" <[email protected]> wrote in message
news:[email protected]...
> Has anyone used the Jorgensen 1650 hold down clamp on their bench? The
> mount through a 3/4" dog hole.
>
> Coastal tools has them in packs of two for $10.95 (less than $6.00
> apiece).
> At this price, if they work at all, they seem worthwhile.
>
> Here's the link to the clamps I am talking about:
> http://tinyurl.com/74sf2
>
> Bob Davis
They look pretty handy and not much of a $ risk. Only problem I see is
getting to the underside of the bench to mount them if you have drawers and
stuff in the way.
Also consider the Lee Valley bench Wonder Dog or Wonder Pup clamps. They
work from the top if the underside of the bench is not easily accessible.
They are a horizontal clamp, not a hold down like the Jorgies..
http://www.leevalley.com/wood/page.aspx?c=2&p=31130&cat=1,43838,43847&ap=1
They do make a hold down but is more expensive.
http://www.leevalley.com/wood/page.aspx?c=2&p=31149&cat=1,43838,43847&ap=1
On Tue, 24 May 2005 13:20:36 GMT, "BillyBob"
<[email protected]> wrote:
>Has anyone used the Jorgensen 1650 hold down clamp on their bench?
They're very quick and easy to use, but they're so sprngy they don't
allow much clamping force. They're useful when routing, but no use for
hand tools.
They also need to be shimmed to be near horizontal or their clamping
suffers. The teeth on the end of the jaw are pretty sharp and damaging
too.
Take a standard F type clamp and take the fixed jaw off. Bore a hole in your
bench large enough for the bar to pass through. Line the hole with a piece
of pipe to protect the bench. Drop the modified clamp in the hole and there
you are. I have two in my bench. Work great.
"BillyBob" <[email protected]> wrote in message
news:[email protected]...
>
> "George" <george@least> wrote in message
> news:[email protected]...
>
> > I've used 'em, and they're not going to hold even close to the Veritas,
or
> > even the wedge type Roy Underhill uses. The use of the word "flexible"
> > suits how they hold fairly well.
>
> Thanks, George. I went to a local dealer and had a hands-on look at the
> Veritas hold down. Now I understand why it costs what it does. Its quite a
> piece of machinery. I brought one home to give it a whirl. I'm not sure
> about the shaft on it. The literature does not mention it and its not
> obvious from the pictures. The shaft has a very shallow and sharp thread
> running the full length. This gives it some gripping power in the dog
hole.
> However, it may also wear out your dog hole in a hurry. I tried it on a
> maple work bench at the dealer. Little tiny wood shavings came out of the
> hole when I pulled the clamp back out. Hmmm, but I bought it anyway to
see
> how it works on my bench. I'm sure I can return it if I decide to, within
a
> couple of days.
>
> Bob
>
>
On Tue, 24 May 2005 13:20:36 GMT, "BillyBob" <[email protected]>
wrote:
>Has anyone used the Jorgensen 1650 hold down clamp on their bench? The
>mount through a 3/4" dog hole.
>
>Coastal tools has them in packs of two for $10.95 (less than $6.00 apiece).
>At this price, if they work at all, they seem worthwhile.
>
>Here's the link to the clamps I am talking about: http://tinyurl.com/74sf2
>
>Bob Davis
>
Bob.. I really like these: simple, work very well and inexpensive.. (I usually
get them on sale for $1.99 each..
http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=41885
mac
Please remove splinters before emailing