Meanie <[email protected]> wrote in news:[email protected]:
> On 12/29/2015 9:07 PM, Meanie wrote:
>
>
> My apologies. I sometimes jump the gun and ask a question without
> doing some investigation.
>
> I just viewed an install video for that unit by Grizzly personnel.
> They made it look easy and it appears it will be. Therefore, if anyone
> cares to chime in with real life experiences on anything I should be
> aware of, I'd appreciate it.
>
> Thanks again.
I had a minor issue with mine, where the bolt was larger than the
sockets I had and there was no room to get a crescent wrench in to
tighten. I had to make a trip to Lowe's to buy a properly sized socket.
Some report alignment issues with their kits, and there's often a pin
that's supposed to keep things aligned. Sometimes they don't get that
put in place properly and it causes problems.
As for difficulty, you may find a friend a useful thing to have. You
can do it yourself (I did), but having someone to take the weight of the
top half of the saw will help in installing the riser block.
FWIW, I've got a Jet saw and used a Powermatic riser. The Grizzly kit
may be different, but there's quite a few saws out there built the same
way.
Puckdropper
--
Make it to fit, don't make it fit.
On 12/29/2015 9:36 PM, Puckdropper wrote:
> Meanie <[email protected]> wrote in news:[email protected]:
>
>> On 12/29/2015 9:07 PM, Meanie wrote:
>>
>>
>> My apologies. I sometimes jump the gun and ask a question without
>> doing some investigation.
>>
>> I just viewed an install video for that unit by Grizzly personnel.
>> They made it look easy and it appears it will be. Therefore, if anyone
>> cares to chime in with real life experiences on anything I should be
>> aware of, I'd appreciate it.
>>
>> Thanks again.
>
> I had a minor issue with mine, where the bolt was larger than the
> sockets I had and there was no room to get a crescent wrench in to
> tighten. I had to make a trip to Lowe's to buy a properly sized socket.
>
> Some report alignment issues with their kits, and there's often a pin
> that's supposed to keep things aligned. Sometimes they don't get that
> put in place properly and it causes problems.
>
> As for difficulty, you may find a friend a useful thing to have. You
> can do it yourself (I did), but having someone to take the weight of the
> top half of the saw will help in installing the riser block.
>
> FWIW, I've got a Jet saw and used a Powermatic riser. The Grizzly kit
> may be different, but there's quite a few saws out there built the same
> way.
>
> Puckdropper
>
Same for Delta.
Wound up not using the pins for alignment.
Bought a combo wrench for the large size bolt.
Exact same situation as you had Puck.
--
Jeff
"Ed Pawlowski" wrote in message
news:[email protected]...
>On 12/29/2015 9:07 PM, Meanie wrote:
>> What degree of difficulty is involved with the install of a riser kit?
>> Specifically for a Grizzly G0555.
>>
>> Thank you
>The only really difficult part is getting the blade back on. They lose one
>size in width when you stretch them i.e. a 1/2" blade becomes 3/8", the
>3/8" will be 1/4". The good new is what was originally a 1/4" blade will
>be great for tight curves.
;~)
> I had a minor issue with mine, where the bolt was larger than the
> sockets I had and there was no room to get a crescent wrench in to
> tighten. I had to make a trip to Lowe's to buy a properly sized socket.
Yep, same here. It's a large bolt inside an enclosed area. You have to have
the right size wrench and socket.
> Some report alignment issues with their kits, and there's often a pin
> that's supposed to keep things aligned. Sometimes they don't get that
> put in place properly and it causes problems.
I had that problem. I had a difficult time trying to get the wheels
coplaner. Eventually I had to drill the holes a bit wider that the pins fit
into to gain just a slight margin of adjustment. Worked fine after that.
Anthony Watson
www.mountainsoftware.com
www.watsondiy.com
On 12/30/2015 1:26 PM, Ed Pawlowski wrote:
> On 12/29/2015 9:07 PM, Meanie wrote:
>> What degree of difficulty is involved with the install of a riser kit?
>> Specifically for a Grizzly G0555.
>>
>> Thank you
>
>
> The only really difficult part is getting the blade back on. They lose
> one size in width when you stretch them i.e. a 1/2" blade becomes
> 3/8", the 3/8" will be 1/4". The good new is what was originally a 1/4"
> blade will be great for tight curves.
Jeez! ;~)
On Fri, 1 Jan 2016 14:31:05 -0500, Meanie <[email protected]>
wrote:
>On 12/30/2015 7:51 PM, OFWW wrote:
>> On Wed, 30 Dec 2015 14:04:21 +0000, Spalted Walt
>> <[email protected]> wrote:
>>
>>> Meanie <[email protected]> wrote:
>>>
>>>> On 12/29/2015 9:07 PM, Meanie wrote:
>>>>
>>>>
>>>> My apologies. I sometimes jump the gun and ask a question without doing
>>>> some investigation.
>>>>
>>>> I just viewed an install video for that unit by Grizzly personnel. They
>>>> made it look easy and it appears it will be. Therefore, if anyone cares
>>>> to chime in with real life experiences on anything I should be aware of,
>>>> I'd appreciate it.
>>>>
>>>> Thanks again.
>>>
>>> I've got the G0555X and the same riser kit (H3051). Just make
>>> ABSOLUTELY sure that the 'UP ARROW' that is on the riser is facing the
>>> back side (the motor side). As Puckdropper said, the task is much
>>> easier with 2 people.
>>>
>>> After you finsh, and before you begin aligning your new 105" blade, I
>>> HIGHLY reccomend watching the following video ---> TWICE.
>>>
>>> https://www.youtube.com/watch?v=wGbZqWac0jU
>>>
>>> Pay particular attention to the coplanar beatdown: ^_^
>>>
>>> https://www.youtube.com/watch?v=wGbZqWac0jU#t=357
>>>
>> I'm glad you brought that up, my BS was a delta like saw, made in
>> Gardena, Calif. I had to replace the belts on the wheels, and the new
>> ones were slightly crowned when installed. (supposed to be) and I
>> started off going crazy on the co-planar bit, but got frustrated, saw
>> that video, set the wheels back to where they were, and set them up
>> per his instructions, and voila, everything, and I do mean everything
>> snapped into place. Now the blade runs on the center crown of the top
>> belt, with the Teeth just off the crown so no teeth marks.
>>
>> When trying to co-plane, the saw blade wouldn't fit through the guides
>> and would have required sliding the wheels on the shaft until you
>> found the sweet spot, if there was one. But adjusting the saw as
>> specified if fit right into the guides, top and bottom, and all was
>> good. No drifts.
>>
>> Went to adjust the bottom and top guides to fit a new blade, and
>> {{SNAP!}} goes the set screw. First one, then another. The brackets
>> that held the iron blocks where all pot metal, and they started
>> cracking on me. Finally took them out and found the pot metal was
>> crumbling. Bad, bad, deterioration. Looked up for replacement parts,
>> it was a no go. Then spotted the newest fancy bearing/wheel guides and
>> did my research found out they would work, BUT! $200 bucks plus ea,
>> for top and bottom. WHAT! I say, I can buy a whole saw for near that
>> amount, and I just have a basically hobby shop. I searched and search,
>> thought and thought and woke up one morning and said, I can do that!
>>
>> So I went to the local metal shop, bought some square tubing, and cold
>> rolled stock and went home and cut and brazed the pieces together
>> using the old stuff as by guide, and then polished up the brackets and
>> voila! after cleaning the saw mounting portion they fit better than
>> the originals, and were very easy to adjust. Went to the local store
>> and bought both 1/4" blocks for the blades and also bought some kind
>> of graphite block stuff for it, used the graphite and reset the
>> adjustments and haven't looked back. The saw now works great, swapping
>> blades is easy to do, set up for the ride on the wheels, and set the
>> adjustment for the blade guides.
>>
>> I'm thinking, after hearing how some guys just trashed their old BS
>> because the failed guides that I should hunt them down, make my new
>> ones and sell the saws, making a good profit, but NAW, I retired and
>> want to wood work. BTW, the material for the guide blocks was less
>> than 20 bucks total, not counting the block kits.
>>
>> But bottom line the co-planar thing is out, IMHO.
>>
>Thanks for the link. I learned much and tuned my band saw.
Credit for the link goes to spalted Walt.
I agree it is good, and easy.
On 12/29/2015 8:36 PM, Puckdropper wrote:
> As for difficulty, you may find a friend a useful thing to have.
Yep. Remember clearly that it was a bit of hassle doing it alone many
years ago, but eventually got it done. Been much easier with a helper.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On 12/29/2015 9:07 PM, Meanie wrote:
My apologies. I sometimes jump the gun and ask a question without doing
some investigation.
I just viewed an install video for that unit by Grizzly personnel. They
made it look easy and it appears it will be. Therefore, if anyone cares
to chime in with real life experiences on anything I should be aware of,
I'd appreciate it.
Thanks again.
On 12/30/2015 7:51 PM, OFWW wrote:
> On Wed, 30 Dec 2015 14:04:21 +0000, Spalted Walt
> <[email protected]> wrote:
>
>> Meanie <[email protected]> wrote:
>>
>>> On 12/29/2015 9:07 PM, Meanie wrote:
>>>
>>>
>>> My apologies. I sometimes jump the gun and ask a question without doing
>>> some investigation.
>>>
>>> I just viewed an install video for that unit by Grizzly personnel. They
>>> made it look easy and it appears it will be. Therefore, if anyone cares
>>> to chime in with real life experiences on anything I should be aware of,
>>> I'd appreciate it.
>>>
>>> Thanks again.
>>
>> I've got the G0555X and the same riser kit (H3051). Just make
>> ABSOLUTELY sure that the 'UP ARROW' that is on the riser is facing the
>> back side (the motor side). As Puckdropper said, the task is much
>> easier with 2 people.
>>
>> After you finsh, and before you begin aligning your new 105" blade, I
>> HIGHLY reccomend watching the following video ---> TWICE.
>>
>> https://www.youtube.com/watch?v=wGbZqWac0jU
>>
>> Pay particular attention to the coplanar beatdown: ^_^
>>
>> https://www.youtube.com/watch?v=wGbZqWac0jU#t=357
>>
> I'm glad you brought that up, my BS was a delta like saw, made in
> Gardena, Calif. I had to replace the belts on the wheels, and the new
> ones were slightly crowned when installed. (supposed to be) and I
> started off going crazy on the co-planar bit, but got frustrated, saw
> that video, set the wheels back to where they were, and set them up
> per his instructions, and voila, everything, and I do mean everything
> snapped into place. Now the blade runs on the center crown of the top
> belt, with the Teeth just off the crown so no teeth marks.
>
> When trying to co-plane, the saw blade wouldn't fit through the guides
> and would have required sliding the wheels on the shaft until you
> found the sweet spot, if there was one. But adjusting the saw as
> specified if fit right into the guides, top and bottom, and all was
> good. No drifts.
>
> Went to adjust the bottom and top guides to fit a new blade, and
> {{SNAP!}} goes the set screw. First one, then another. The brackets
> that held the iron blocks where all pot metal, and they started
> cracking on me. Finally took them out and found the pot metal was
> crumbling. Bad, bad, deterioration. Looked up for replacement parts,
> it was a no go. Then spotted the newest fancy bearing/wheel guides and
> did my research found out they would work, BUT! $200 bucks plus ea,
> for top and bottom. WHAT! I say, I can buy a whole saw for near that
> amount, and I just have a basically hobby shop. I searched and search,
> thought and thought and woke up one morning and said, I can do that!
>
> So I went to the local metal shop, bought some square tubing, and cold
> rolled stock and went home and cut and brazed the pieces together
> using the old stuff as by guide, and then polished up the brackets and
> voila! after cleaning the saw mounting portion they fit better than
> the originals, and were very easy to adjust. Went to the local store
> and bought both 1/4" blocks for the blades and also bought some kind
> of graphite block stuff for it, used the graphite and reset the
> adjustments and haven't looked back. The saw now works great, swapping
> blades is easy to do, set up for the ride on the wheels, and set the
> adjustment for the blade guides.
>
> I'm thinking, after hearing how some guys just trashed their old BS
> because the failed guides that I should hunt them down, make my new
> ones and sell the saws, making a good profit, but NAW, I retired and
> want to wood work. BTW, the material for the guide blocks was less
> than 20 bucks total, not counting the block kits.
>
> But bottom line the co-planar thing is out, IMHO.
>
Thanks for the link. I learned much and tuned my band saw.
On 12/30/2015 9:04 AM, Spalted Walt wrote:
> Meanie <[email protected]> wrote:
>
>> On 12/29/2015 9:07 PM, Meanie wrote:
>>
>>
>> My apologies. I sometimes jump the gun and ask a question without doing
>> some investigation.
>>
>> I just viewed an install video for that unit by Grizzly personnel. They
>> made it look easy and it appears it will be. Therefore, if anyone cares
>> to chime in with real life experiences on anything I should be aware of,
>> I'd appreciate it.
>>
>> Thanks again.
>
> I've got the G0555X and the same riser kit (H3051). Just make
> ABSOLUTELY sure that the 'UP ARROW' that is on the riser is facing the
> back side (the motor side). As Puckdropper said, the task is much
> easier with 2 people.
>
> After you finsh, and before you begin aligning your new 105" blade, I
> HIGHLY reccomend watching the following video ---> TWICE.
>
> https://www.youtube.com/watch?v=wGbZqWac0jU
>
> Pay particular attention to the coplanar beatdown: ^_^
>
> https://www.youtube.com/watch?v=wGbZqWac0jU#t=357
>
>
I was corrected to you as the the original link provider cause I didn't
go back far enough.
Thanks. It taught me well.
On Wed, 30 Dec 2015 14:26:30 -0500, Ed Pawlowski <[email protected]> wrote:
>On 12/29/2015 9:07 PM, Meanie wrote:
>> What degree of difficulty is involved with the install of a riser kit?
>> Specifically for a Grizzly G0555.
>>
>> Thank you
>
>
>The only really difficult part is getting the blade back on. They lose
>one size in width when you stretch them i.e. a 1/2" blade becomes
>3/8", the 3/8" will be 1/4". The good new is what was originally a 1/4"
>blade will be great for tight curves.
LOL, Dude you must make the Hulk look like a WIMP! Hands down. LOL
On 12/29/2015 9:07 PM, Meanie wrote:
> What degree of difficulty is involved with the install of a riser kit?
> Specifically for a Grizzly G0555.
>
> Thank you
The only really difficult part is getting the blade back on. They lose
one size in width when you stretch them i.e. a 1/2" blade becomes
3/8", the 3/8" will be 1/4". The good new is what was originally a 1/4"
blade will be great for tight curves.
On Wed, 30 Dec 2015 14:04:21 +0000, Spalted Walt
<[email protected]> wrote:
>Meanie <[email protected]> wrote:
>
>>On 12/29/2015 9:07 PM, Meanie wrote:
>>
>>
>>My apologies. I sometimes jump the gun and ask a question without doing
>>some investigation.
>>
>>I just viewed an install video for that unit by Grizzly personnel. They
>>made it look easy and it appears it will be. Therefore, if anyone cares
>>to chime in with real life experiences on anything I should be aware of,
>>I'd appreciate it.
>>
>>Thanks again.
>
>I've got the G0555X and the same riser kit (H3051). Just make
>ABSOLUTELY sure that the 'UP ARROW' that is on the riser is facing the
>back side (the motor side). As Puckdropper said, the task is much
>easier with 2 people.
>
>After you finsh, and before you begin aligning your new 105" blade, I
>HIGHLY reccomend watching the following video ---> TWICE.
>
>https://www.youtube.com/watch?v=wGbZqWac0jU
>
>Pay particular attention to the coplanar beatdown: ^_^
>
>https://www.youtube.com/watch?v=wGbZqWac0jU#t=357
>
I'm glad you brought that up, my BS was a delta like saw, made in
Gardena, Calif. I had to replace the belts on the wheels, and the new
ones were slightly crowned when installed. (supposed to be) and I
started off going crazy on the co-planar bit, but got frustrated, saw
that video, set the wheels back to where they were, and set them up
per his instructions, and voila, everything, and I do mean everything
snapped into place. Now the blade runs on the center crown of the top
belt, with the Teeth just off the crown so no teeth marks.
When trying to co-plane, the saw blade wouldn't fit through the guides
and would have required sliding the wheels on the shaft until you
found the sweet spot, if there was one. But adjusting the saw as
specified if fit right into the guides, top and bottom, and all was
good. No drifts.
Went to adjust the bottom and top guides to fit a new blade, and
{{SNAP!}} goes the set screw. First one, then another. The brackets
that held the iron blocks where all pot metal, and they started
cracking on me. Finally took them out and found the pot metal was
crumbling. Bad, bad, deterioration. Looked up for replacement parts,
it was a no go. Then spotted the newest fancy bearing/wheel guides and
did my research found out they would work, BUT! $200 bucks plus ea,
for top and bottom. WHAT! I say, I can buy a whole saw for near that
amount, and I just have a basically hobby shop. I searched and search,
thought and thought and woke up one morning and said, I can do that!
So I went to the local metal shop, bought some square tubing, and cold
rolled stock and went home and cut and brazed the pieces together
using the old stuff as by guide, and then polished up the brackets and
voila! after cleaning the saw mounting portion they fit better than
the originals, and were very easy to adjust. Went to the local store
and bought both 1/4" blocks for the blades and also bought some kind
of graphite block stuff for it, used the graphite and reset the
adjustments and haven't looked back. The saw now works great, swapping
blades is easy to do, set up for the ride on the wheels, and set the
adjustment for the blade guides.
I'm thinking, after hearing how some guys just trashed their old BS
because the failed guides that I should hunt them down, make my new
ones and sell the saws, making a good profit, but NAW, I retired and
want to wood work. BTW, the material for the guide blocks was less
than 20 bucks total, not counting the block kits.
But bottom line the co-planar thing is out, IMHO.
Meanie <[email protected]> wrote:
>On 12/29/2015 9:07 PM, Meanie wrote:
>
>
>My apologies. I sometimes jump the gun and ask a question without doing
>some investigation.
>
>I just viewed an install video for that unit by Grizzly personnel. They
>made it look easy and it appears it will be. Therefore, if anyone cares
>to chime in with real life experiences on anything I should be aware of,
>I'd appreciate it.
>
>Thanks again.
I've got the G0555X and the same riser kit (H3051). Just make
ABSOLUTELY sure that the 'UP ARROW' that is on the riser is facing the
back side (the motor side). As Puckdropper said, the task is much
easier with 2 people.
After you finsh, and before you begin aligning your new 105" blade, I
HIGHLY reccomend watching the following video ---> TWICE.
https://www.youtube.com/watch?v=wGbZqWac0jU
Pay particular attention to the coplanar beatdown: ^_^
https://www.youtube.com/watch?v=wGbZqWac0jU#t=357