Anyone using them?
I'm going to build a bookcase with plywood and want to trim the edges with
solid oak. In the past I've used biscuits and glued them, but I've been
thinking that it may be more accurate to use the router bits. I'm going to
have about 30' of edge to do.
Infinity makes both a "V" and a t & g set. Whiteside has a V. Any
preference if you do use them?
http://www.routerbits.com/cgi-routerbits/sr.cgi?1208579704_8650+400
http://www.infinitytools.com/products.asp?dept=1300
Lee Valley has one that can be shimmed, but is far more pricier $129
http://www.leevalley.com/wood/page.aspx?c=2&p=50698&cat=1,46168
--
Ed
http://pages.cthome.net/edhome/
On Apr 19, 12:50=A0am, "Edwin Pawlowski" <[email protected]> wrote:
> Anyone using them?
>
> I'm going to build a bookcase with plywood and want to trim the edges with=
> solid oak. In the past I've used biscuits and glued them, but I've been
> thinking that it may be more accurate to use the router bits. I'm going to=
> have about 30' of edge to do.
>
> Infinity makes both a "V" and a t & g set. =A0Whiteside has a V. Any
> preference if you do use them?
>
> http://www.routerbits.com/cgi-routerbits/sr.cgi?1208579704_8650+400
>
> http://www.infinitytools.com/products.asp?dept=3D1300
>
> Lee Valley has one that can be shimmed, but is far more pricier =A0$129htt=
p://www.leevalley.com/wood/page.aspx?c=3D2&p=3D50698&cat=3D1,46168
> --
Personally, I find that whole solid wood edge approach a waste of
time. A quality edgebanding tape, of matching wood veneer, gives me
the look and speed I want. Iron it on, sand and finish.
Now, if it is going to be a shelf in a library or book store, okay
then go for the solid wood edge..... in which case I'd go for the
Infinity set-up.
(Don't tell anybody, but I nail a flat strip on with a 23 ga pinner
and let the glue do its job.)
Tape is my friend. I have posted this before, but it illustrates that
one can get a satisfying finish with tape.
http://i123.photobucket.com/albums/o290/Robatoy/Gunrack.jpg
"Edwin Pawlowski" wrote:
> Seems that there is no definite consensus or that the bit is "must
> have" item. I think I may hold off.
The more I thought about this, the less I liked the router approach.
T&G edge banding begs for a decent table saw and a good dado blade
set.
If you run the stock thru end for end, you insure the banding will be
centered on the plywood.
It also is a lot faster on th T/S than using a router.
A dado has many mory applications than a special purpose router bit.
Just my thoughts.
Lew
Edwin Pawlowski wrote:
> Anyone using them?
>
> I'm going to build a bookcase with plywood and want to trim the edges
> with solid oak. In the past I've used biscuits and glued them, but
> I've been thinking that it may be more accurate to use the router
> bits. I'm going to have about 30' of edge to do.
>
> Infinity makes both a "V" and a t & g set. Whiteside has a V. Any
> preference if you do use them?
>
> http://www.routerbits.com/cgi-routerbits/sr.cgi?1208579704_8650+400
>
> http://www.infinitytools.com/products.asp?dept=1300
>
> Lee Valley has one that can be shimmed, but is far more pricier $129
> http://www.leevalley.com/wood/page.aspx?c=2&p=50698&cat=1,46168
I have no problems just gluing on a strip then trimming. Just as easy IMO
as trying to fit a formed strip precisely.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
>Anyone using them?
I've got the set from Burgess. Pricey ($120 if I recall correctly,
4-5 yrs ago).
The bits come with multiple shims and bearings, so the depth and width
of cut can be finely adjusted. Good quality cuts, and the subsequent
fit of the pieces is very good.
As far as the technique in general, I think the final result using an
edge-banding system is far superior to a flat glue-up. Pluswhich, you
can leave the edge piece thick, then mill different edges on it. I
built a workspace for my daughter using 3/4" cherry ply and solid
cherry edge-banding, and used an oval bullnose on the edges to make
them a bit softer.
Usual disclaimers apply.
-Zz
"dadiOH" <[email protected]> wrote in message
news:mulOj.8350$Zk5.1557@trnddc05...
> Edwin Pawlowski wrote:
>> Anyone using them?
>>
>> I'm going to build a bookcase with plywood and want to trim the edges
>> with solid oak. In the past I've used biscuits and glued them, but
>> I've been thinking that it may be more accurate to use the router
>> bits. I'm going to have about 30' of edge to do.
>>
>> Infinity makes both a "V" and a t & g set. Whiteside has a V. Any
>> preference if you do use them?
>>
>> http://www.routerbits.com/cgi-routerbits/sr.cgi?1208579704_8650+400
>>
>> http://www.infinitytools.com/products.asp?dept=1300
>>
>> Lee Valley has one that can be shimmed, but is far more pricier $129
>> http://www.leevalley.com/wood/page.aspx?c=2&p=50698&cat=1,46168
>
> I have no problems just gluing on a strip then trimming. Just as easy IMO
> as trying to fit a formed strip precisely.
>
> --
>
> dadiOH
Seems that there is no definite consensus or that the bit is "must have"
item. I think I may hold off. The bookcase I'll be making is for my next
door neighbor. He's going to supply the wood and I'll supply the labor.
Good trade off as I've not had to start my lawnmower for the past three
years and this assures it will be four.
"Edwin Pawlowski" wrote:
> Anyone using them?
>
> I'm going to build a bookcase with plywood and want to trim the
> edges with solid oak. In the past I've used biscuits and glued them,
> but I've been thinking that it may be more accurate to use the
> router bits. I'm going to have about 30' of edge to do.
SFWIW, either one increases the glue surface dramatically; however,
getting that "just so" fit will probably be a problem.
Think I would make the solid oak edge pieces 1/16" oversize, then
clean up with a pilot trim bit after glue is set.
Lew