I am installing a whirlpool tub into an alcove, where the center wall
is an exterior wall. There is room to have about a 6" surround on each
side of the tub, or I could have it off-center and go up to 9" on one
side.
SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
to decide if it's even possible with a topside plumbing access. Not
only would it have to be large enough to facilitate installation and
potentially repair, it would also still need to seal.
I'm building the surround out of some leftover brazilian cherry we
have from the stair remodel (I build box newels for that).
Is this possible, or is it just as bad of an idea as it feels like?
Should I consider an outside plumbing access? This is a 2nd floor
master bath, stick-framed, with a brick vernier exterior.
The other alternative is to just install the fixtures on the front
side, but you'd have to get in around them, and they wouldn't be as
nice to look at.
Thanks!
-Mike
On Jun 29, 9:15 pm, "Chip Buchholtz" <[email protected]> wrote:
> In rec.woodworking Mike Reed <[email protected]> wrote:
> : SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
> : to decide if it's even possible with a topside plumbing access. Not
> : only would it have to be large enough to facilitate installation and
> : potentially repair, it would also still need to seal.
>
> What's underneath the bathroom? Can you access the plumbing from
> underneath?
>
> --- Chip
Thanks for the replies so far.
The family room is underneath, no way for access.
What do you think about access from above? (through the wood) I can't
think of anything that would work well and still look right. Panels to
the sides of the fixtures, with the fixtures on a separate panel would
have seams that would need to be sealed (near the fixtures and near
the walls). The center (fixture) panel would need extra support
beneath. On top of that, the access panels on either side would need
some way to pull on them or unscrew them - I dunno if caulking them in
place would be adequate.
Access from outside may just be risky from a time standpoint. If it
starts leaking or we need access for some reason, gotta climb a 20'
ladder to deal with it.
I was hoping there was some slick trick for this that I just hadn't
seen.
To answer other posts above: we're in Austin, TX, and the pipes would
not be inside the wall. And, yes, I am talking about the trim that
goes on top of the tub, into the tile. I guess normally the tile is
called the surround :)
Thanks,
Mike
On Jun 30, 11:40 am, HerHusband <[email protected]> wrote:
> Mike,
>
> Are you talking about mounting the fixture on the back side of the tub?
> If so, that would be very awkward to use unless you have a small tub or
> plan on climbing in the tub just to start filling it with water.
That's a good point I hadn't considered.
> Is this a tub in a platform situation where the fixture mounts on the
> deck, or it is a regular tub where the fixtures mount on the wall?
Fixture on the deck
>
> You mention it's an alcove. What's on the two end walls? Could you put an
> access panel on the back side of one of the end walls?
One wall has the master bedroom, the other has the water closet.
Access panel wouldn't look good. I don't mind front access -- I'm
building a jatoba front for the tub too (standard frame and panel A&C
look). It would be easy enough to just caulk that piece in place and
slice it out for access if it was ever needed.
> I mounted our master tub faucet in the front left corner of our tub
> platform. It's easy to access, out of the way when climbing in and out of
> the tub, and doesn't get in the way if we both take a bath together (a
> person at each end).
We'll have to look into that, but this is a pretty crisp rectangular
tub, so corner fixture may look awkward. I'll take a look.
> One end of our master tub butts up against the vanity cabinet. I
> originally planned on putting the access inside the cabinet, since the
> front of our tub platform had to be waterproofed (we have a large walk-in
> shower outside the tub). In the end, I installed the fixture before I set
> the tub in. Any typical repairs needed to the faucet can be accomplished
> from above the deck anyway. And if I need to repair the plumbing for some
> reason, I figured I could remove the tub, or pop a hole up from our
> crawlspace. Either way, that's no different than repairing the plumbing
> anywhere else in the house.
Interesting point. I could plumb the tub around to where there is
access in front, install the tub, then sweat the final connections
from the front. I guess if it's solid soldered copper all the way
through, it is no different than being in a wall. Hmm. There is the
fixture access leanin over the whole tub issue though.
Thanks for the replies so far everyone.
-Mike
On Fri, 29 Jun 2007 15:27:01 -0500, Rick Samuel wrote:
> Subject: Re: Plumbing access through top of tub surround?
> From: "Rick Samuel" <[email protected]>
> Newsgroups: alt.home.repair,rec.woodworking
> Date: Fri, 29 Jun 2007 15:27:01 -0500
>
> Outside wall aren't the best for things that freeze.
<snip html crap>
Please disable that html garbage in your news reader.
"Mike Reed" <[email protected]> wrote in message
news:[email protected]...
>I am installing a whirlpool tub into an alcove, where the center wall
> is an exterior wall. There is room to have about a 6" surround on each
> side of the tub, or I could have it off-center and go up to 9" on one
> side.
>
> SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
> to decide if it's even possible with a topside plumbing access. Not
> only would it have to be large enough to facilitate installation and
> potentially repair, it would also still need to seal.
>
> I'm building the surround out of some leftover brazilian cherry we
> have from the stair remodel (I build box newels for that).
>
> Is this possible, or is it just as bad of an idea as it feels like?
> Should I consider an outside plumbing access? This is a 2nd floor
> master bath, stick-framed, with a brick vernier exterior.
>
> The other alternative is to just install the fixtures on the front
> side, but you'd have to get in around them, and they wouldn't be as
> nice to look at.
>
> Thanks!
>
> -Mike
>
It seems to me the best option would be to mount the faucet off to the side,
in front of the tub, with an access door on the wall below the tub. Who says
the faucet needs to be centered? Any thing else is just asking for trouble
down the road. With the access on top, water will certainly get trough at
some point.
Greg
"readandpostrosie" <[email protected]> wrote in message
news:[email protected]...
>
> "Art" <[email protected]> wrote in message
> news:[email protected]...
>> Don't worry too much about it. No one uses these things much anyway.
>
>
>
> that is what everyone is telling me too!
>
Amen to that. Many of the luxo-features they were adding to houses in last
ten years, to suck in the yuppies, were just fads. Jacuzzis, hot tubs,
multi-head showers, 'restaurant style' kitchens, that sort of thing. Once
the novelty wears off and/or kids come along, who has time to use them, much
less keep them cleaned and maintained? I know a dozen people who have ripped
out their outdoor hot tubs or even complete pools, just to simplify their
lives. Now that flat panels and all-in-one home theater electronics are the
current thing good enough for 90% of users, I bet some of those people who
spent a gazillion dollars on rear-projection component systems in dedicated
rooms are starting to feel kinda silly.
(Kinda reminds me of the NuTone Home Intercom Systems, that were de riguer
in upscale houses back in the 1960s. Not to mention the hot-water dispensers
and built-in appliances from the same vendor.)
In a house that should last a hundred years or so, you want to be careful
how tightly you integrate technology that will be worn out or no longer
popular in ten or twenty years.
aem sends....
"Art" <[email protected]> wrote in message
news:[email protected]...
> Don't worry too much about it. No one uses these things much anyway.
that is what everyone is telling me too!
My tub is a 2 person oval and faucets are in one front corner and the spout
in the other front corner. Neither block access. Don't worry too much
about it. No one uses these things much anyway.
"Mike Reed" <[email protected]> wrote in message
news:[email protected]...
>I am installing a whirlpool tub into an alcove, where the center wall
> is an exterior wall. There is room to have about a 6" surround on each
> side of the tub, or I could have it off-center and go up to 9" on one
> side.
>
> SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
> to decide if it's even possible with a topside plumbing access. Not
> only would it have to be large enough to facilitate installation and
> potentially repair, it would also still need to seal.
>
> I'm building the surround out of some leftover brazilian cherry we
> have from the stair remodel (I build box newels for that).
>
> Is this possible, or is it just as bad of an idea as it feels like?
> Should I consider an outside plumbing access? This is a 2nd floor
> master bath, stick-framed, with a brick vernier exterior.
>
> The other alternative is to just install the fixtures on the front
> side, but you'd have to get in around them, and they wouldn't be as
> nice to look at.
>
> Thanks!
>
> -Mike
>
Mike Reed <[email protected]> writes:
>I am installing a whirlpool tub into an alcove, where the center wall
>is an exterior wall. There is room to have about a 6" surround on each
>side of the tub, or I could have it off-center and go up to 9" on one
>side.
>
>SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
>to decide if it's even possible with a topside plumbing access. Not
>only would it have to be large enough to facilitate installation and
>potentially repair, it would also still need to seal.
>
>I'm building the surround out of some leftover brazilian cherry we
>have from the stair remodel (I build box newels for that).
>
>Is this possible, or is it just as bad of an idea as it feels like?
>Should I consider an outside plumbing access? This is a 2nd floor
>master bath, stick-framed, with a brick vernier exterior.
>
>The other alternative is to just install the fixtures on the front
>side, but you'd have to get in around them, and they wouldn't be as
>nice to look at.
>
>Thanks!
>
>-Mike
>
I assume by surround, you're referring to a platform at the top of
the whirlpool between it and the wall, and you wish to plumb between
the pool and the wall on the exterior wall side. I don't immediately
see anything wrong with this idea, aside from access; If you live
somewhere with winters, I wouldn't put the plumbing _in_ the exterior
wall, however.
scott
On the other hand, after mowing my hilly lawn in hot weather I would first
take a shower and then a dip in the jacuzzi right next to it. It is amazing
how much more dirt the jacuzzi would get out of my pores when I was already
shower clean. But now I hire a company to mow the lawn.
"aemeijers" <[email protected]> wrote in message
news:[email protected]...
>
> "readandpostrosie" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "Art" <[email protected]> wrote in message
>> news:[email protected]...
>>> Don't worry too much about it. No one uses these things much anyway.
>>
>>
>>
>> that is what everyone is telling me too!
>>
> Amen to that. Many of the luxo-features they were adding to houses in last
> ten years, to suck in the yuppies, were just fads. Jacuzzis, hot tubs,
> multi-head showers, 'restaurant style' kitchens, that sort of thing. Once
> the novelty wears off and/or kids come along, who has time to use them,
> much less keep them cleaned and maintained? I know a dozen people who have
> ripped out their outdoor hot tubs or even complete pools, just to simplify
> their lives. Now that flat panels and all-in-one home theater electronics
> are the current thing good enough for 90% of users, I bet some of those
> people who spent a gazillion dollars on rear-projection component systems
> in dedicated rooms are starting to feel kinda silly.
>
> (Kinda reminds me of the NuTone Home Intercom Systems, that were de riguer
> in upscale houses back in the 1960s. Not to mention the hot-water
> dispensers and built-in appliances from the same vendor.)
>
> In a house that should last a hundred years or so, you want to be careful
> how tightly you integrate technology that will be worn out or no longer
> popular in ten or twenty years.
>
> aem sends....
>
Mike,
> I am installing a whirlpool tub into an alcove, where the center wall
> is an exterior wall. There is room to have about a 6" surround on each
> side of the tub, or I could have it off-center and go up to 9" on one
> side. SWMBO wants the fixtures on the middle (exterior) wall
Are you talking about mounting the fixture on the back side of the tub?
If so, that would be very awkward to use unless you have a small tub or
plan on climbing in the tub just to start filling it with water.
Is this a tub in a platform situation where the fixture mounts on the
deck, or it is a regular tub where the fixtures mount on the wall?
You mention it's an alcove. What's on the two end walls? Could you put an
access panel on the back side of one of the end walls? Our guest bath has
a closet on the other side of the fixture wall, which made it easy to
hide an access panel inside the closet.
> The other alternative is to just install the fixtures on the front
> side, but you'd have to get in around them, and they wouldn't be as
> nice to look at.
I mounted our master tub faucet in the front left corner of our tub
platform. It's easy to access, out of the way when climbing in and out of
the tub, and doesn't get in the way if we both take a bath together (a
person at each end).
> if it's even possible with a topside plumbing access.
I wouldn't recommend top access if you can avoid it. It's just a
potential place for water to seep into.
One end of our master tub butts up against the vanity cabinet. I
originally planned on putting the access inside the cabinet, since the
front of our tub platform had to be waterproofed (we have a large walk-in
shower outside the tub). In the end, I installed the fixture before I set
the tub in. Any typical repairs needed to the faucet can be accomplished
from above the deck anyway. And if I need to repair the plumbing for some
reason, I figured I could remove the tub, or pop a hole up from our
crawlspace. Either way, that's no different than repairing the plumbing
anywhere else in the house.
Anthony
Mike,
>> You mention it's an alcove. What's on the two end walls? Could you
>> put an access panel on the back side of one of the end walls?
> One wall has the master bedroom, the other has the water closet.
> Access panel wouldn't look good.
Could you make the entire back side of the water closet wall a removeable
panel?
> Interesting point. I could plumb the tub around to where there is
> access in front, install the tub, then sweat the final connections
> from the front. I guess if it's solid soldered copper all the way
> through, it is no different than being in a wall. Hmm. There is the
> fixture access leanin over the whole tub issue though.
One other thought, you mentioned this was a "whirlpool" tub right? If so
that involves a pump and electrical equipment. In that case, you are
required by code to have an access panel for the electrical connection and
pump maintenance. Sounds like you're OK with a front access panel, so just
mount everything up front (or on an end you can reach from the front) and
you should be OK.
Anthony
This is a multi-part message in MIME format.
------=_NextPart_000_005F_01C7BA61.F0CB7C50
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Outside wall aren't the best for things that freeze.
"Mike Reed" <[email protected]> wrote in message =
news:[email protected]...
I am installing a whirlpool tub into an alcove, where the center wall
is an exterior wall. There is room to have about a 6" surround on each
side of the tub, or I could have it off-center and go up to 9" on one
side.
SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
to decide if it's even possible with a topside plumbing access. Not
only would it have to be large enough to facilitate installation and
potentially repair, it would also still need to seal.
I'm building the surround out of some leftover brazilian cherry we
have from the stair remodel (I build box newels for that).
Is this possible, or is it just as bad of an idea as it feels like?
Should I consider an outside plumbing access? This is a 2nd floor
master bath, stick-framed, with a brick vernier exterior.
The other alternative is to just install the fixtures on the front
side, but you'd have to get in around them, and they wouldn't be as
nice to look at.
Thanks!
-Mike
------=_NextPart_000_005F_01C7BA61.F0CB7C50
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3D"MSHTML 6.00.6000.16481" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV><FONT face=3D"Courier New" size=3D2>Outside wall aren't the best =
for things=20
that freeze.</FONT></DIV>
<BLOCKQUOTE=20
style=3D"PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; =
BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV>"Mike Reed" <<A=20
href=3D"mailto:[email protected]">[email protected]</A>> =
wrote in=20
message <A=20
=
href=3D"news:[email protected]">news:=
[email protected]</A>...</DIV>I=20
am installing a whirlpool tub into an alcove, where the center =
wall<BR>is an=20
exterior wall. There is room to have about a 6" surround on =
each<BR>side of=20
the tub, or I could have it off-center and go up to 9" on=20
one<BR>side.<BR><BR>SWMBO wants the fixtures on the middle (exterior) =
wall,=20
and I'm trying<BR>to decide if it's even possible with a topside =
plumbing=20
access. Not<BR>only would it have to be large enough to facilitate=20
installation and<BR>potentially repair, it would also still need to=20
seal.<BR><BR>I'm building the surround out of some leftover brazilian =
cherry=20
we<BR>have from the stair remodel (I build box newels for =
that).<BR><BR>Is=20
this possible, or is it just as bad of an idea as it feels =
like?<BR>Should I=20
consider an outside plumbing access? This is a 2nd floor<BR>master =
bath,=20
stick-framed, with a brick vernier exterior.<BR><BR>The other =
alternative is=20
to just install the fixtures on the front<BR>side, but you'd have to =
get in=20
around them, and they wouldn't be as<BR>nice to look=20
at.<BR><BR>Thanks!<BR><BR>-Mike<BR></BLOCKQUOTE></BODY></HTML>
------=_NextPart_000_005F_01C7BA61.F0CB7C50--
In rec.woodworking Mike Reed <[email protected]> wrote:
: SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
: to decide if it's even possible with a topside plumbing access. Not
: only would it have to be large enough to facilitate installation and
: potentially repair, it would also still need to seal.
What's underneath the bathroom? Can you access the plumbing from
underneath?
--- Chip
On Fri, 29 Jun 2007 12:44:48 -0700, Mike Reed <[email protected]>
wrote:
>
>
>SWMBO wants the fixtures on the middle (exterior) wall, and I'm trying
>to decide if it's even possible with a topside plumbing access. Not
>only would it have to be large enough to facilitate installation and
>potentially repair, it would also still need to seal.
I'll say this, when I had a bathtub with the valves and faucet on the
side, it was very convenient. I didn't have to move to adjust the
water. I loved my luxury 1930 bathtub, with the drain control
outside. I could float in it with no more than a square inch of me
touching the sides or bottom.
Now I have one with the valves and faucet near my toes. I've done toe
exercises and greased the stems to make them easy to turn with my
toes, but they got tight again later. I have some control but end up
sitting up to adjust them most of the time.
They couldn't put them on the side here, because under the sheetrock
is the cinder block that separates my house from the next house.
In the luxury building, in my bathroom, the wall only separated the
tub from the kitchen. And in the other full bathroom, I think the tub
was against an outside wall, but the fixtures were still on the side.