I recently came into a "buffalo" tablesaw what was missing a miter
gauge. Everthing on the saw seems to be fine except for the miter
slots on the table. The miter slots on this tablesaw seems to be just
shy of 3/4" in width. The depth does seem to match 3/8" but a
standard size miter guage will just not fit in the slot. Does anyone
know of a place or website that I can purchase sliders that will fit
this slot so I can retrofit a miter guage to work with the saw?
I called the manufacturer of the saw and they said that they no longer
carry parts for it so buying a new one from the factory is out.
Any suggestions would be appreciated.
Charles
Charles Harris wrote:
> I recently came into a "buffalo" tablesaw what was missing a miter
> gauge. Everthing on the saw seems to be fine except for the miter
> slots on the table. The miter slots on this tablesaw seems to be just
> shy of 3/4" in width. The depth does seem to match 3/8" but a
> standard size miter guage will just not fit in the slot. Does anyone
> know of a place or website that I can purchase sliders that will fit
> this slot so I can retrofit a miter guage to work with the saw?
>
> I called the manufacturer of the saw and they said that they no longer
> carry parts for it so buying a new one from the factory is out.
>
> Any suggestions would be appreciated.
>
> Charles
Many Craftsman saws have a slightly undersized miter slot. You can try
one of the Sears miter gauges. Osborne also makes a miter gauge to fit
the Sears saws, See:
http://www.newwoodworker.com/osbrnsmlslot1.html
--
Jack Novak
Buffalo, NY - USA
Greetings and Salutations...
On Tue, 30 Sep 2003 14:14:10 GMT, "Mike in Mystic"
<[email protected]> wrote:
>You can make a miter sled with hardwood runners to fit the slots. I suppose
>you could take a miter gauge and remove the miter bar and replace it with a
>hardwood runner that you made as well. Shouldn't be too tough.
>
>Mike
>
>--
>
>There are no stupid questions.
>There are a LOT of inquisitive idiots.
>
>
>"Charles Harris" <[email protected]> wrote in message
>news:[email protected]...
>> I recently came into a "buffalo" tablesaw what was missing a miter
>> gauge. Everthing on the saw seems to be fine except for the miter
>> slots on the table. The miter slots on this tablesaw seems to be just
>> shy of 3/4" in width. The depth does seem to match 3/8" but a
>> standard size miter guage will just not fit in the slot. Does anyone
>> know of a place or website that I can purchase sliders that will fit
>> this slot so I can retrofit a miter guage to work with the saw?
>>
>> I called the manufacturer of the saw and they said that they no longer
>> carry parts for it so buying a new one from the factory is out.
>>
>> Any suggestions would be appreciated.
>>
>> Charles
>
>
Or...measure the exact width of the slot, then, go to
Sears and measure the size of their miter gauge bar. The
fact that their miter bars are slightly under 3/4" is
a continual annoyance to those that want to "upgrade" the
miter gauge on the saw, but, might be a blessing in
disguise for you.
Alternatively, you could take it to a machine
shop, and, have the slots widened to 3/4".
Alternatively, you could get a miter gauge with
a 3/4" bar and carefully grind the bar to fit the slot.
If the top had enough meat to it, I would be inclined to
have the slots widened. However, you could probably
grind the bar down at home....and it WOULD be cheaper.
I would strongly recommend, though, that you take half
the difference off each side, to ensure that the pivot
point for the gauge will remain centered on the bar.
Regards
Dave Mundt
Take your miter gauge to the machine shop not the table. They should easily
be able to mill the bar to specs to fit the slot.
Joe Ingham
"Charles Harris" <[email protected]> wrote in message
news:[email protected]...
> From what I have seen so far, The machine shops said it would tricky
> to get the table mounted to the milling machine due to its size. I think
> I am going to opt for buy the stock already milled to the correct size.
>
> What I found that was interesting that I wanted to share with everyone is
> that the dimensions of the miter slots were 18mm X 9mm. I say it was
> interesting as that ratio is the same as the standard slots.
>
> On Tue, 30 Sep 2003 12:11:24 -0700, David Hall wrote:
>
> > [email protected] (Charles Harris) wrote in message
news:<[email protected]>...
> >> I recently came into a "buffalo" tablesaw what was missing a miter
> >> gauge. Everthing on the saw seems to be fine except for the miter
> >> slots on the table. The miter slots on this tablesaw seems to be just
> >> shy of 3/4" in width. The depth does seem to match 3/8" but a
> >> standard size miter guage will just not fit in the slot. Does anyone
> >> know of a place or website that I can purchase sliders that will fit
> >> this slot so I can retrofit a miter guage to work with the saw?
> >>
> >> I called the manufacturer of the saw and they said that they no longer
> >> carry parts for it so buying a new one from the factory is out.
> >>
> >> Any suggestions would be appreciated.
> >>
> >> Charles
> >
> >
> > You might check with Shopsmith. Their miter slot is just less than
> > 3/4" - I believe it is 11/16ths - they sell a reasonable miter guage.
> > Their miter bars have an adjustment set-screw that allows the bar to
> > be adjusted to a tight fit. The bar for the model 510/520 is for a
> > T-slot miter and the bar for the 500 is for a non-T application (the
> > only difference is a "washer" attached to the 510/520 bar). If it
> > fits, they have a pletora of Incra products desined to fit the
> > Shopsmith miter slots on their web catalog.
> >
> > www.shopsmith.com
> >
> > Dave Hall
> > I own one, but am otherwise unaffiliated
>
[email protected] (Charles Harris) wrote in message news:<[email protected]>...
> I recently came into a "buffalo" tablesaw what was missing a miter
> gauge. Everthing on the saw seems to be fine except for the miter
> slots on the table. The miter slots on this tablesaw seems to be just
> shy of 3/4" in width. The depth does seem to match 3/8" but a
> standard size miter guage will just not fit in the slot. Does anyone
> know of a place or website that I can purchase sliders that will fit
> this slot so I can retrofit a miter guage to work with the saw?
>
> I called the manufacturer of the saw and they said that they no longer
> carry parts for it so buying a new one from the factory is out.
>
> Any suggestions would be appreciated.
>
> Charles
You might check with Shopsmith. Their miter slot is just less than
3/4" - I believe it is 11/16ths - they sell a reasonable miter guage.
Their miter bars have an adjustment set-screw that allows the bar to
be adjusted to a tight fit. The bar for the model 510/520 is for a
T-slot miter and the bar for the 500 is for a non-T application (the
only difference is a "washer" attached to the 510/520 bar). If it
fits, they have a pletora of Incra products desined to fit the
Shopsmith miter slots on their web catalog.
www.shopsmith.com
Dave Hall
I own one, but am otherwise unaffiliated
You can make a miter sled with hardwood runners to fit the slots. I suppose
you could take a miter gauge and remove the miter bar and replace it with a
hardwood runner that you made as well. Shouldn't be too tough.
Mike
--
There are no stupid questions.
There are a LOT of inquisitive idiots.
"Charles Harris" <[email protected]> wrote in message
news:[email protected]...
> I recently came into a "buffalo" tablesaw what was missing a miter
> gauge. Everthing on the saw seems to be fine except for the miter
> slots on the table. The miter slots on this tablesaw seems to be just
> shy of 3/4" in width. The depth does seem to match 3/8" but a
> standard size miter guage will just not fit in the slot. Does anyone
> know of a place or website that I can purchase sliders that will fit
> this slot so I can retrofit a miter guage to work with the saw?
>
> I called the manufacturer of the saw and they said that they no longer
> carry parts for it so buying a new one from the factory is out.
>
> Any suggestions would be appreciated.
>
> Charles
> have the slots widened. However, you could probably
> grind the bar down at home....and it WOULD be cheaper.
> I would strongly recommend, though, that you take half
> the difference off each side, to ensure that the pivot
> point for the gauge will remain centered on the bar.
> Regards
> Dave Mundt
Why does it need to be centered on the bar? I mean, it is going to be within
a 1/8" of the center anyway? It should make no difference at all where the
pivot point is since the gauge is not pivoting when you use it anyway.
Better instead to just grind one side so you at least have one "factory"
edge to it. It will save you trouble.
-Jack
From what I have seen so far, The machine shops said it would tricky
to get the table mounted to the milling machine due to its size. I think
I am going to opt for buy the stock already milled to the correct size.
What I found that was interesting that I wanted to share with everyone is
that the dimensions of the miter slots were 18mm X 9mm. I say it was
interesting as that ratio is the same as the standard slots.
On Tue, 30 Sep 2003 12:11:24 -0700, David Hall wrote:
> [email protected] (Charles Harris) wrote in message news:<[email protected]>...
>> I recently came into a "buffalo" tablesaw what was missing a miter
>> gauge. Everthing on the saw seems to be fine except for the miter
>> slots on the table. The miter slots on this tablesaw seems to be just
>> shy of 3/4" in width. The depth does seem to match 3/8" but a
>> standard size miter guage will just not fit in the slot. Does anyone
>> know of a place or website that I can purchase sliders that will fit
>> this slot so I can retrofit a miter guage to work with the saw?
>>
>> I called the manufacturer of the saw and they said that they no longer
>> carry parts for it so buying a new one from the factory is out.
>>
>> Any suggestions would be appreciated.
>>
>> Charles
>
>
> You might check with Shopsmith. Their miter slot is just less than
> 3/4" - I believe it is 11/16ths - they sell a reasonable miter guage.
> Their miter bars have an adjustment set-screw that allows the bar to
> be adjusted to a tight fit. The bar for the model 510/520 is for a
> T-slot miter and the bar for the 500 is for a non-T application (the
> only difference is a "washer" attached to the 510/520 bar). If it
> fits, they have a pletora of Incra products desined to fit the
> Shopsmith miter slots on their web catalog.
>
> www.shopsmith.com
>
> Dave Hall
> I own one, but am otherwise unaffiliated