One of you guys showed pics of your outfeed table that folded up and/or
extended or something cool like that.
My space is limited, so I need something that folds up and out quickly.
Who's was it? Can you post the pics again, so I can steal it. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
My saw has a fence that uses a rear rail in addition to the front rail. Will
this roller outfeed still attach to the saw and clear the rear rail?
Russ
<[email protected]> wrote in message
news:d613f097-f50b-4620-975d-8996c7570acc@j24g2000yqa.googlegroups.com...
> > My space is limited, so I need something that folds up and out quickly.
> > ...
> ..... HTC makes a 15 roller out feed that folds down. ... I think I
> prefer the roller out feed as it indeed folds down relatively close to the
> saw, attaches strictly to the saw .....
>
> http://www.htcproductsinc.com/outrs.html
I'll second that. It attaches easily, simply, and quickly and does a
good job.
On Oct 11, 9:58=A0pm, -MIKE- <[email protected]> wrote:
> One of you guys showed pics of your outfeed table that folded up and/or
> extended or something cool like that.
>
> My space is limited, so I need something that folds up and out quickly.
>
> Who's was it? =A0Can you post the pics again, so I can steal it. =A0:-)
>
> --
>
> =A0 -MIKE-
>
> =A0 "Playing is not something I do at night, it's my function in life"
> =A0 =A0 =A0--Elvin Jones =A0(1927-2004)
> =A0 --
> =A0http://mikedrums.com
> =A0 [email protected]
> =A0 ---remove "DOT" ^^^^ to reply
What kind of saw do you have?
> I clamped the angle where I thought it should go, marked the holes and
> drilled them oversize for some adjustment.
Thanks. That's much simpler than the concepts I was trying to flesh out.
Couple more quick questions.
Is there support for the outfeed section? I was expecting to see a support
member from the bottom of the table saw (or from the floor) to the
outfeed/extension hinge, but I don't see any support in the photo at the
hinge (apologies if this was already discussed above).
There is no hole in the outfeed table for a blade guard. Do you use a blade
guard that does not require space in the back of the table saw?
Best,
Christopher
I don't know about cool but it's a big
table in two pieces and can handle an entire
sheet of plywood on the table through the
entire cut. It does require a fair amount
if room.
http://home.att.net/~mboceanside/wsb/html/view.cgi-photo.html--SiteID-638867.html
http://home.att.net/~mboceanside/wsb/html/view.cgi-photo.html--SiteID-639331.html
It was a short article in FWW a few years back and I made a "version"
of my own.
Not too difficult and very flexible.
-MIKE- wrote:
> One of you guys showed pics of your outfeed table that folded up and/or
> extended or something cool like that.
>
> My space is limited, so I need something that folds up and out quickly.
>
> Who's was it? Can you post the pics again, so I can steal it. :-)
>
>
"Greg O" <[email protected]> wrote in message
news:[email protected]...
>I built one very simular to this one,
>http://www.wooddreams.net/images/Big_Images/Shop/Shop/24outfeed_table.JPG
> The biggest differance was I used a full 4'x8' sheet of melimine, and
> edged the table with 1'x3' pine to stiffen it up. My table is as wide as
> the saw, with the 52" inch fence, about 7 feet. With the table up I have a
> work surface ao about 7'x7'. The table folds down, and adds only about 12"
> to the depth of the saw. I had built a outfeed table when my saw had just
> a 32" fence, and built it out of a 4'x4' sheet of melemine, but always
> cussed the "notched" out corner. .
Mike
I can't remember where I saw it, maybe shopnotes, but there was an article
about the outfeed table very similar to the one Greg built. IIRC it
connected to the back of the saw with dowels that had corresponding holes in
the saw. The legs folded like a card table and on the bottom of each leg
there were sliding levelers that the user clamped with spring clamps. It
seemed to be able to connect / disconnect very easy. Maybe an idea.
Or you could just do what I do is use my rolling work table - NYW. And
every time I need to use move all the stuff that was on another flat surface
in the shop that I had to move to use that.
Larry C
"Morris Dovey" <[email protected]> wrote in message
news:[email protected]...
> -MIKE- wrote:
>> [email protected] wrote:
> Attaches easily, simply, quickly, does a good job, and is /really/
> inexpensive:
>
> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
Yeah but how much was that Incra fence? ;!)
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>>
>>> Attaches easily, simply, quickly, does a good job, and is /really/
>>> inexpensive:
>>>
>>> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
>>
>>
>> Yeah but how much was that Incra fence? ;!)
>
> I saw that, too! :-) <drool>
I was intereste in the fence at one time then I looked at how much room is
required for a 50" rip capcity and the room required to store it when it is
off the saw. You might want to take a look at that. ;~)
Delta makes a collapsable outfeed table accessory. You could easily
copy.
http://www.tools-plus.com/delta-50-302.html
On Oct 11, 6:58=A0pm, -MIKE- <[email protected]> wrote:
> One of you guys showed pics of your outfeed table that folded up and/or
> extended or something cool like that.
>
> My space is limited, so I need something that folds up and out quickly.
>
> Who's was it? =A0Can you post the pics again, so I can steal it. =A0:-)
>
> --
>
> =A0 -MIKE-
>
> =A0 "Playing is not something I do at night, it's my function in life"
> =A0 =A0 =A0--Elvin Jones =A0(1927-2004)
> =A0 --
> =A0http://mikedrums.com
> =A0 [email protected]
> =A0 ---remove "DOT" ^^^^ to reply
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
>
> I looked into the ball rollers, before, when I was going to make a
> stand, because they don't push the stock in one direction.
>
> But in this case, with them being mounted perfectly perpendicular to the
> blade, it would be a benefit.
I was going to mention also that the HCT out feed roller stand will support
a sheet of plywood after ripping it. Basically you don't need some one on
the other end to catch it to prevent it from tipping. That works for 8'
boards also.
A little pricey but it is probably the last one you will need to purchace
and it does not sag over time. It is definately an upgrade to any saw.
"Christopher Glaeser" <[email protected]> wrote in message
news:[email protected]...
>> I mounted an angle to the rear of the saw's table and screwed the top to
>> it from underneath.
>
> Oh, OK. Did the angle iron have slots instead of round holes so you could
> adjust the hieght where the saw table meets the outfeed table? Or, did
> you use some type of shim?
>
> Best,
> Christopher
>
>
I clamped the angle where I thought it should go, marked the holes and
drilled them oversize for some adjustment.
Greg
SonomaProducts.com wrote:
> Delta makes a collapsable outfeed table accessory. You could easily
> copy.
>
> http://www.tools-plus.com/delta-50-302.html
>
I have that one. IMO, you could make one yourself that works better; I
did that for the other side of the table saw to make it compatible for
large panels. I posted about this one several years ago after buying it.
My take on it was that this was the kind of project Delta gave to its
newest engineers. It was difficult to assemble; not hard to understand,
just physically difficult and really not very well thought out. Take a
look at one in person if you can, it isn't a difficult project.
> On Oct 11, 6:58Â pm, -MIKE- <[email protected]> wrote:
>> One of you guys showed pics of your outfeed table that folded up and/or
>> extended or something cool like that.
>>
>> My space is limited, so I need something that folds up and out quickly.
>>
>> Who's was it? Â Can you post the pics again, so I can steal it. Â :-)
>>
>> --
>>
>> -MIKE-
>>
>> "Playing is not something I do at night, it's my function in life"
>> --Elvin Jones  (1927-2004)
>> --
>> http://mikedrums.com
>> [email protected]
>> ---remove "DOT" ^^^^ to reply
--
There is never a situation where having more rounds is a disadvantage
Rob Leatham
"Christopher Glaeser" <[email protected]> wrote in message
news:[email protected]...
> >I built one very simular to this one,
> >http://www.wooddreams.net/images/Big_Images/Shop/Shop/24outfeed_table.JPG
>
> How did you mount the outfeed to the table? Did you drill holes in the
> bottom of the L angle iron?
>
> Best,
> Christopher
>
>
I mounted an angle to the rear of the saw's table and screwed the top to it
from underneath. Where the out feed table meets the extension table I used a
strip of 2"x1/8" steel strap and overlapped the two tables and screwed then
to the strap from underneath. The legs are some 1" square tubing with 3/4"
threaded rod couplers welded on, with 3/4" threaded rod for adjustable feet
screwed into the coupling. The legs are mounted to the table with two pieces
of angle iron each with a bolt through them so the legs can hinge up, out of
the way. A couple of supports hold the legs at 90 degrees when the table is
in use. Similar to these,
http://www.rockler.com/product.cfm?page=429&filter=lid%20support
I have the whole saw on a mobile base I made. the frame is on four casters,
and I have two more 3/4" threaded rods I can screw down to the floor to keep
the saw in place. The out feed table will hinge down and almost hit the
floor. That is one thing to watch out for when you cut the out feed table
pieces, make sure you cut the table narrow enough so it will not hit the
floor!
Greg
I have one of these. Thinking about getting a second one . Use it
around all sides of machinery as required . I cut a a piece of
plywood to use as a tabletop. It has two boards screwed onto the
bottom that fit tightly between the end rollers to keep the top from
moving.
http://www.general.ca/site_general/accessories/universal/50-167e.html
Ldb
-MIKE- wrote:
> One of you guys showed pics of your outfeed table that folded up and/or
> extended or something cool like that.
>
> My space is limited, so I need something that folds up and out quickly.
>
> Who's was it? Can you post the pics again, so I can steal it. :-)
>
>
It is designed to fold up at the saw table.
Both tables fold into one another.
I'll try to find that FWW article...
-MIKE- wrote:
> That's the one! Yes, Pat, it's very cool.
> The cool part is how it's extendable like that.
> What I need to do, however, is make the whole assembly hinge down
> against the saw, out of the way.
> > My space is limited, so I need something that folds up and out quickly.=
...
> ..... HTC makes a 15 roller out feed that folds down. ... =A0I think I
> prefer the roller out feed as it indeed folds down relatively close to th=
e
> saw, attaches strictly to the saw .....
>
> http://www.htcproductsinc.com/outrs.html
I'll second that. It attaches easily, simply, and quickly and does a
good job.
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> One of you guys showed pics of your outfeed table that folded up and/or
> extended or something cool like that.
>
> My space is limited, so I need something that folds up and out quickly.
>
> Who's was it? Can you post the pics again, so I can steal it. :-)
>
WoodSmith magazine has an article on building an out feed that folds down,
you need to search their archives. I probably build it for my older saw
14-15 years ago. I sold that saw and again used it about 3 months ago, the
table is still fine.
Alternatively HTC makes a 15 roller out feed that folds down, I have had
that out feed in the Jet version on my Jet for the past 10 years. I think I
prefer the roller out feed as it indeed folds down relatively close to the
saw, attaches strictly to the saw so you do not have to putz with legs if
you move the saw, and with rollers vs. a solid top, it tends to stay clear
and not become a catch-all surface.
http://www.htcproductsinc.com/outrs.html
Russ Stanton wrote:
> My saw has a fence that uses a rear rail in addition to the front rail.
> Will this roller outfeed still attach to the saw and clear the rear rail?
...
"MOST" fence systems will have enough clearance. I'd contact HTC and
ask about any specific one. Have dimensions handy when do, of course.
If it's one of the standard PM, Delta, Jet, etc., designs they'll have
accounted for it; some of the imports perhaps not if it is unique or
oversize compared to others.
--
Leon wrote:
> I think I
> prefer the roller out feed as it indeed folds down relatively close to the
> saw, attaches strictly to the saw so you do not have to putz with legs if
> you move the saw, and with rollers vs. a solid top, it tends to stay clear
> and not become a catch-all surface.
>
I hear that. It *has* to go up and down easily, because of the limited
space I have... for that same reason, it's just too easy for it to turn
into another workspace that has to be cleared off in order to use the tool.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
[email protected] wrote:
>>> My space is limited, so I need something that folds up and out quickly. ...
>
>> ..... HTC makes a 15 roller out feed that folds down. ... I think I
>> prefer the roller out feed as it indeed folds down relatively close to the
>> saw, attaches strictly to the saw .....
>>
>> http://www.htcproductsinc.com/outrs.html
>
> I'll second that. It attaches easily, simply, and quickly and does a
> good job.
>
I love that, but it's about 150 percent what I paid for my saw. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Pat Barber wrote:
> I don't know about cool but it's a big
> table in two pieces and can handle an entire
> sheet of plywood on the table through the
> entire cut. It does require a fair amount
> if room.
>
> http://home.att.net/~mboceanside/wsb/html/view.cgi-photo.html--SiteID-638867.html
>
> http://home.att.net/~mboceanside/wsb/html/view.cgi-photo.html--SiteID-639331.html
>
>
> It was a short article in FWW a few years back and I made a "version"
> of my own.
>
> Not too difficult and very flexible.
>
That's the one! Yes, Pat, it's very cool.
The cool part is how it's extendable like that.
What I need to do, however, is make the whole assembly hinge down
against the saw, out of the way.
Now I have the "baseline" of my idea, so I'll combine it with the good
from everything else posted and see what I come up with.
Thanks for reading and posting.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
-MIKE- wrote:
> [email protected] wrote:
>>>> My space is limited, so I need something that folds up and out
>>>> quickly. ...
>>
>>> ..... HTC makes a 15 roller out feed that folds down. ... I think I
>>> prefer the roller out feed as it indeed folds down relatively close
>>> to the
>>> saw, attaches strictly to the saw .....
>>>
>>> http://www.htcproductsinc.com/outrs.html
>>
>> I'll second that. It attaches easily, simply, and quickly and does a
>> good job.
>
> I love that, but it's about 150 percent what I paid for my saw. :-)
Attaches easily, simply, quickly, does a good job, and is /really/
inexpensive:
http://www.iedu.com/DeSoto/Projects/OutfeedTable/
Not shown on that page, but I added miter slot extensions for a
handy-dandy (simple/quick/good/inexpensive) crosscut sled:
http://www.iedu.com/DeSoto/Projects/CrosscutSled/
Poverty is the mother of invention. :)
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
dpb wrote:
> -MIKE- wrote:
> ...
>
>> I love that, but it's about 150 percent what I paid for my saw. :-)
>
> They wouldn't be terribly difficult to fabricate w/ an inexpensive
> roller set or two from Northern/Harbor/whoever. I've thought about it a
> lot but never gotten that particular round tuit, of course... :)
>
I've been down that road before, so I don't have to ask for direction,
this time. :-)
I looked into the ball rollers, before, when I was going to make a
stand, because they don't push the stock in one direction.
But in this case, with them being mounted perfectly perpendicular to the
blade, it would be a benefit.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Morris Dovey wrote:
> Attaches easily, simply, quickly, does a good job, and is /really/
> inexpensive:
>
> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
>
> Not shown on that page, but I added miter slot extensions for a
> handy-dandy (simple/quick/good/inexpensive) crosscut sled:
>
> http://www.iedu.com/DeSoto/Projects/CrosscutSled/
>
> Poverty is the mother of invention. :)
>
Thanks.
You're always good for the Occam's razor of jigs and accessories ideas.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
LdB wrote:
> I have one of these. Thinking about getting a second one . Use it
> around all sides of machinery as required . I cut a a piece of plywood
> to use as a tabletop. It has two boards screwed onto the bottom that
> fit tightly between the end rollers to keep the top from moving.
>
> http://www.general.ca/site_general/accessories/universal/50-167e.html
>
> Ldb
>
Good idea.
But in my case, once it's a tabletop, it's a tabletop, you know? :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Leon wrote:
> "Morris Dovey" <[email protected]> wrote in message
> news:[email protected]...
>> -MIKE- wrote:
>>> [email protected] wrote:
>
>
>> Attaches easily, simply, quickly, does a good job, and is /really/
>> inexpensive:
>>
>> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
>
>
> Yeah but how much was that Incra fence? ;!)
>
>
I saw that, too! :-) <drool>
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Leon wrote:
>
>> Attaches easily, simply, quickly, does a good job, and is /really/
>> inexpensive:
>>
>> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
>
>
> Yeah but how much was that Incra fence? ;!)
>
I saw that, too! :-) <drool>
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Leon wrote:
> "Morris Dovey" <[email protected]> wrote in message
> news:[email protected]...
>> -MIKE- wrote:
>>> [email protected] wrote:
>
>
>> Attaches easily, simply, quickly, does a good job, and is /really/
>> inexpensive:
>>
>> http://www.iedu.com/DeSoto/Projects/OutfeedTable/
>
> Yeah but how much was that Incra fence? ;!)
With the long rails, it was enough to hurt - seven years ago. Happily,
it only hurt for a short while. :)
I still have the original rails, a set of longer Delta rails, and the
original fence - and still don't like 'em.
The Incra fence and rails just made the job a little easier than it
would have been with the original rails.
I suppose my carefully-kept secret is out - that by building as much as
possible for myself, I've had a bit left over for some of the nice
things I /couldn't/ build. :)
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
> Mike
>
> I can't remember where I saw it, maybe shopnotes, but there was an
> article about the outfeed table very similar to the one Greg built.
> IIRC it connected to the back of the saw with dowels that had
> corresponding holes in the saw. The legs folded like a card table and
> on the bottom of each leg there were sliding levelers that the user
> clamped with spring clamps. It seemed to be able to connect /
> disconnect very easy. Maybe an idea.
>
The leveling concept is something which I really need to incorporate,
since I'm working in a garage with a sloped floor. My SCM portable stand
has great legs on the roller extensions that quickly and easily adjust
for leveling them.
> Or you could just do what I do is use my rolling work table - NYW. And
> every time I need to use move all the stuff that was on another flat
> surface in the shop that I had to move to use that.
>
> Larry C
That's what I've done in the past, with my much smaller table saw.
It's one reason I want this to be quickly and easily folded down out of
the way. I figure it has to be easier to put down, out of the way than
it is to put stuff on it for working. :-) That's one of the reasons the
roller concept intrigues me.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
<snip>:
: The leveling concept is something which I really need to incorporate,
: since I'm working in a garage with a sloped floor. My SCM portable stand
: has great legs on the roller extensions that quickly and easily adjust
: for leveling them.
<snip>:
I have the same problem with my garage floor. For my shop made stuff I have
been using elevator bolts on the bottom of the legs and they work just fine.
My local Ace HW carries them. If you're unfamiliar with them look here
http://www.fastenal.com/web/products.ex?N=999600009
Art
Artemus wrote:
> "-MIKE-" <[email protected]> wrote in message
> news:[email protected]...
>
> <snip>:
> : The leveling concept is something which I really need to incorporate,
> : since I'm working in a garage with a sloped floor. My SCM portable stand
> : has great legs on the roller extensions that quickly and easily adjust
> : for leveling them.
> <snip>:
>
> I have the same problem with my garage floor. For my shop made stuff I have
> been using elevator bolts on the bottom of the legs and they work just fine.
> My local Ace HW carries them. If you're unfamiliar with them look here
> http://www.fastenal.com/web/products.ex?N=999600009
> Art
>
Yes, I'm very familiar with them. Tangent.....
I needed some for a project. Went to Lowes to look in their special
fasteners bins.
Found a separate drawer labeled, "elevator bolts." Opened drawer..
nothing inside.
Asked the hardware "associate" if they had any. He said no, they don't
carry them.
I pointed to the drawer and said, "sure you do, look."
He said, "yeah, I see the drawer, but they don't stock those any more."
I said, "well, how about you take the label off the drawer."
"Oh, we're not allowed."
"Why"
"They don't like having blank labels."
"So, they'd rather have empty drawers that piss off the customers?"
Now, *every* timer I go to Lowes, I walk down that aisle, open that
drawer and ask where the elevator bolts are. Sooner or later, they'll
take the label off. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
>
> I clamped the angle where I thought it should go, marked the holes and
> drilled them oversize for some adjustment.
> Greg
That's how Delta does it.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
jtpr wrote:
> On Oct 11, 9:58 pm, -MIKE- <[email protected]> wrote:
>> One of you guys showed pics of your outfeed table that folded up and/or
>> extended or something cool like that.
>>
>> My space is limited, so I need something that folds up and out quickly.
>>
>> Who's was it? Can you post the pics again, so I can steal it. :-)
>>
>
> What kind of saw do you have?
Delta 36-982
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
"Christopher Glaeser" <[email protected]> wrote in message
news:[email protected]...
>> I clamped the angle where I thought it should go, marked the holes and
>> drilled them oversize for some adjustment.
>
> Thanks. That's much simpler than the concepts I was trying to flesh out.
>
> Couple more quick questions.
>
> Is there support for the outfeed section? I was expecting to see a
> support member from the bottom of the table saw (or from the floor) to the
> outfeed/extension hinge, but I don't see any support in the photo at the
> hinge (apologies if this was already discussed above).
>
> There is no hole in the outfeed table for a blade guard. Do you use a
> blade guard that does not require space in the back of the table saw?
>
> Best,
> Christopher
>
>
I forgot about the to supports that mount right before the hinge in the
table, and run down at an angle to the base of the saw. As for the blade
guard, I used a hole saw and bored a hole so I can mount the blade gaurd, at
least I did on my first version, I have not done so on my current table. I
probalby should, but I am one of those rebels that does not use a blade
gaurd very often any way!
Greg O
I built one very simular to this one,
http://www.wooddreams.net/images/Big_Images/Shop/Shop/24outfeed_table.JPG
The biggest differance was I used a full 4'x8' sheet of melimine, and edged
the table with 1'x3' pine to stiffen it up. My table is as wide as the saw,
with the 52" inch fence, about 7 feet. With the table up I have a work
surface ao about 7'x7'. The table folds down, and adds only about 12" to the
depth of the saw. I had built a outfeed table when my saw had just a 32"
fence, and built it out of a 4'x4' sheet of melemine, but always cussed the
"notched" out corner. .
"Russ Stanton" <[email protected]> wrote in message
news:%[email protected]...
> My saw has a fence that uses a rear rail in addition to the front rail.
> Will this roller outfeed still attach to the saw and clear the rear rail?
YES! I have a Jet cabinet saw with the longer right extension table so it
has the back rail to support the table. With the cabinet saw the out feed
assembly bolts directly to the back saw cabinet. IIRC HTC makes them all a
bit different for any particular saw. IIRC they do/did make one for
contractor saws also.