On Jan 19, 3:24 am, "Michael Hearn Anna Houpt"
<[email protected]> wrote:
> Rip one side then turn upside down and rip again. This way you only need a
> blade to cut 1/2 the thickness. You will need a fence to do this...
>
I agree Mike, this way you can use a handsaw to finish the job, or
spend the $20 for a cheap sawsall and a longer blade and be done.
Lou
Hello... Conner??? Are you there? Folks need your input so that they can
make the proper suggestions. Drop a line to one or all of these posts.
Response is always appreciated. No flame intended.
(apologies for the top-post - just trying to get OPs attention.)
"Connor Aston" <[email protected]> wrote in message
news:[email protected]...
> My table saw is too small to rip the boards up the middle and my
> bandsaw is too small any ideas folks?
>
In article <[email protected]>,
Connor Aston <[email protected]> wrote:
>My table saw is too small to rip the boards up the middle and my
>bandsaw is too small any ideas folks?
>
Are you trying to rip 4 inch thick stock into 2 inch thick stock? Or?
Give us a better idea of what you are starting with and what results
you are after.
--
No dumb questions, just dumb answers.
Larry Wasserman - Baltimore, Maryland - [email protected]
Rip one side then turn upside down and rip again. This way you only need a
blade to cut 1/2 the thickness. You will need a fence to do this...
"Connor Aston" <[email protected]> wrote in message
news:[email protected]...
> My table saw is too small to rip the boards up the middle and my
> bandsaw is too small any ideas folks?
>
> My table saw is too small to rip the boards up the middle and my
> bandsaw is too small any ideas folks?
A few years ago, I needed to cut 1x8 lumber into two thinner boards, for
bending to fit a curved window frame. I didn't own a bandsaw, and my old
Craftsman table saw is limited to about a 2-1/2" cut. The boards were also
ten feet long, which would have made hand cutting a lot of work.
After evaluating my options, I chose to buy a second board for $40 and use
my surface planer to plane the two boards down to the 1/4 inch I needed. I
hated reducing 1/2" of each board to planer shavings, but it was still the
cheapest option I had available. And, the results actually turned out very
nice.
Today I would use my new Grizzly G0555 bandsaw (with riser block) to resaw
the boards. But, at the time I couldn't afford to buy a new tool. Sometimes
you just have to make do with the tools you have.
A couple of other thoughts....
1. Rip the boards into a size that will fit your bandsaw. Resaw the boards
to the desired thickness, then edge glue them back together.
2. Use your tablesaw to cut as deeply as you can down each edge. Then go
back and complete the cut with a handsaw. The two cuts will help guide the
handsaw.
Anthony
> Sorry folks working all weekend. Thanks for the advice I think cutting
> the 8" wide x 4" boards each side and finishing with a handsaw is the
> best option. And as for $40 boards try $200 by the time the redwood
> travels across the Atlantic to Ireland.
$200 a board? Ouch. When you start getting into those prices, it starts
making financial sense to buy a bandsaw, unless this is a one time deal.
In my case, an extra $40 board was a lot cheaper than investing $500 in a
new bandsaw.
Anthony
hello,
use a bandsaw...
or rip on both side with your table saw and finish with a hand saw in the
middle..
cyrille
"Connor Aston" <[email protected]> wrote in message
news:[email protected]...
> My table saw is too small to rip the boards up the middle and my
> bandsaw is too small any ideas folks?
>
"Connor Aston" <[email protected]> wrote in message
news:[email protected]...
> My table saw is too small to rip the boards up the middle and my
> bandsaw is too small any ideas folks?
>
4" wide, or 4" thick?
If wide, I don't understand the problem.
If thick, I have used a ts on the top and on the bottom, and then cut the
web out with a handsaw or a bs. Of course if your wood is 4" thick and 10"
wide, that will not be a great solution.