Hi all,
I have an upcoming project that's still in the "thinking stage", which
is to say that I'm trying yo figure out all of the operations that I'll
need to do and finding ways to do it with my existing skills and
equipment.
I'm using a large ogee bit (1 3/8" radius) to creat a moulding effect.
So far I've done this exclusively on straight stock using the router
table. The upcoming project will need the same moulding edge on an
arched panel. This bit is large, almost like a panel bit, plus I have
very little experience routing freehand so I don't think that's a
viable option.
I'm thinking that I could do this on the table if I position the fence
such that the curve of the piece indexes on the inside edges of the
split fence. i.e. "bridging the gap" with the bit inside the gap as
would be normal. I could easily adjust the depth of cut for multiple
passes and could still use a featherboardd to provide downward
pressure. I would still have to "freehand" the work maintaining
pressure towards the fence.
Any thoughts on this technique or alternate ideas?
Thanks,
Tom
Morris Dovey wrote:
> [email protected] (in
> [email protected]) said:
>
> | Hi all,
> |
> | I have an upcoming project that's still in the "thinking stage",
> | which is to say that I'm trying yo figure out all of the operations
> | that I'll need to do and finding ways to do it with my existing
> | skills and equipment.
> |
> | I'm using a large ogee bit (1 3/8" radius) to creat a moulding
> | effect. So far I've done this exclusively on straight stock using
> | the router table. The upcoming project will need the same moulding
> | edge on an arched panel. This bit is large, almost like a panel
> | bit, plus I have very little experience routing freehand so I don't
> | think that's a viable option.
> |
> | I'm thinking that I could do this on the table if I position the
> | fence such that the curve of the piece indexes on the inside edges
> | of the split fence. i.e. "bridging the gap" with the bit inside the
> | gap as would be normal. I could easily adjust the depth of cut for
> | multiple passes and could still use a featherboardd to provide
> | downward pressure. I would still have to "freehand" the work
> | maintaining pressure towards the fence.
> |
> | Any thoughts on this technique or alternate ideas?
>
> There's some important information you didn't provide:
>
Good questions, and answers below:
> [1] Is arch circular?
No, it's irregular (parabolic).
> [2] Width and height of arch?
The piece to be worked will be about 24" along the curved edge. The
curve is very gradual.
> [3] Material to be routed?
Spanish Cedar - one of the softest hardwoods.
> [4] Thickness of stock to be routed?
Thickness is 1". I was planning to cut the curve with a sabre saw and
then route the edge. The deepest cut of the full profile amounts to
about halfway through the stock (1/2").
> [5] Are you routing inside, outside, or both curves?
Outside only.
> [6] What does "existing skills and equipment" mean?
Without getting too long winded, I was referring to the thought process
we all go through ahead of a project to plan how were going to create
the individual components with the tools we have. Skill comes into the
equation as well, for example cutting large sheet goods. Some people
are skilled enough to cut large pieces on the table saw. I'm not, so
I'd choose a circular saw with a guide. In the case of my current
challenge, I'm very inexperienced with hand-held routing, so I hope to
avoid attempting it with this large bit.
> [7] Can you pre-cut the desired arch with a band saw and/or straight
> router bit?
I was planning to use a saber saw.
> [8] Have you considered making a template to be used with a bit
> incorporating a ball bearing guide?
That's a possibility.
I think I misused the term "freehand". I meant "edge routing" using the
bearing. With that big a bit, I afraid that it will be hard to control
the router, especially since I'm very inexperienced. I'm getting pretty
good at table routing so I'd hoped to find a way to do this on the
table.
Tom
>
> --
> Morris Dovey
> DeSoto Solar
> DeSoto, Iowa USA
> http://www.iedu.com/DeSoto/solar.html
tom wrote:
> It's possible, but I think it'll get a little scary at the ends of your
> stock, without both fences in play. Maybe rough cut the stock extra
> long/wide to avoid the teetering, and give your fingers some extra
> room? Is there a bearing somewhere on this bit? Tom
Yep, that's the way to do it. With enough extra length, I won't have
to get the end of the piece (or my fingers) any where near the bit and
it will always be indexed on two points. The bit has a bearing, but the
fence will control the distance from the cutters.
Great suggestion, thanks!
It will actually be half an arch, because two mirror-image pieces will
comprise the full arch (spaced apart slightly). Each half will be about
24" long.
Imagine the board laying flat against the wall. I'll describe the
left-hand piece. The bottom will be straight (24") and right-hand edge
will be straight (6") and the arched top will curve from the top right
down to a point on the bottom left. There is no left edge because the
arched top meets the bottom edge on the left. The arch is quite
gradual.
Tom
[email protected] wrote:
> Hi all,
>
> I have an upcoming project that's still in the "thinking stage", which
> is to say that I'm trying yo figure out all of the operations that I'll
> need to do and finding ways to do it with my existing skills and
> equipment.
>
> I'm using a large ogee bit (1 3/8" radius) to creat a moulding effect.
> So far I've done this exclusively on straight stock using the router
> table. The upcoming project will need the same moulding edge on an
> arched panel. This bit is large, almost like a panel bit, plus I have
> very little experience routing freehand so I don't think that's a
> viable option.
>
> I'm thinking that I could do this on the table if I position the fence
> such that the curve of the piece indexes on the inside edges of the
> split fence. i.e. "bridging the gap" with the bit inside the gap as
> would be normal. I could easily adjust the depth of cut for multiple
> passes and could still use a featherboardd to provide downward
> pressure. I would still have to "freehand" the work maintaining
> pressure towards the fence.
>
> Any thoughts on this technique or alternate ideas?
>
> Thanks,
> Tom
>
Tom:
Here's how I approached a similar effort with routing small, curved
raised panel pieces in 4/4 cherry for built-in bookcases:
1. Make MDF templates of everything you need to route.
2. Glue 2 handles to back of each template piece.
3. Cut cherry to slightly larger than template.
4. Screw template to back of cherry.
5. Route free-hand (with guide pin) in router table to flush trim cherry
to template with flush trim bit.
6. Mount raised panel bit, crank router speed *waaaaay down* and route
raised, irregular pieces.
Note:
- You'll have to make 3-4 (or more passes) with the raised panel bit.
- Route across the grain first and then with the grain last.
- For some curve pieces, it may make sense to route half the curve and
then do a climb cut to get the second half.
- Make the last pass *very* shallow (1/16" or 1/32") to remove any burn
marks.
This effort was perhaps the scariest work I've done with power tools.
Watching a 3" panel bit inches from your hands is a bit unnerving. Take
your time and stay alert. You can do this safely, just think things through.
~Mark.
[email protected] (in
[email protected]) said:
| Morris Dovey wrote:
|| [email protected] (in
|| [email protected]) said:
||
||| Hi all,
|||
||| I have an upcoming project that's still in the "thinking stage",
||| which is to say that I'm trying yo figure out all of the
||| operations that I'll need to do and finding ways to do it with my
||| existing skills and equipment.
|||
||| I'm using a large ogee bit (1 3/8" radius) to creat a moulding
||| effect. So far I've done this exclusively on straight stock using
||| the router table. The upcoming project will need the same moulding
||| edge on an arched panel. This bit is large, almost like a panel
||| bit, plus I have very little experience routing freehand so I
||| don't think that's a viable option.
|||
||| I'm thinking that I could do this on the table if I position the
||| fence such that the curve of the piece indexes on the inside edges
||| of the split fence. i.e. "bridging the gap" with the bit inside
||| the gap as would be normal. I could easily adjust the depth of
||| cut for multiple passes and could still use a featherboardd to
||| provide downward pressure. I would still have to "freehand" the
||| work maintaining pressure towards the fence.
|||
||| Any thoughts on this technique or alternate ideas?
||
|| There's some important information you didn't provide:
||
| Good questions, and answers below:
|| [1] Is arch circular?
| No, it's irregular (parabolic).
|| [2] Width and height of arch?
| The piece to be worked will be about 24" along the curved edge. The
| curve is very gradual.
|| [3] Material to be routed?
| Spanish Cedar - one of the softest hardwoods.
|| [4] Thickness of stock to be routed?
| Thickness is 1". I was planning to cut the curve with a sabre saw
| and then route the edge. The deepest cut of the full profile
| amounts to about halfway through the stock (1/2").
|| [5] Are you routing inside, outside, or both curves?
| Outside only.
|| [6] What does "existing skills and equipment" mean?
| Without getting too long winded, I was referring to the thought
| process we all go through ahead of a project to plan how were going
| to create the individual components with the tools we have. Skill
| comes into the equation as well, for example cutting large sheet
| goods. Some people are skilled enough to cut large pieces on the
| table saw. I'm not, so I'd choose a circular saw with a guide. In
| the case of my current challenge, I'm very inexperienced with
| hand-held routing, so I hope to avoid attempting it with this large
| bit.
|| [7] Can you pre-cut the desired arch with a band saw and/or
|| straight router bit?
| I was planning to use a saber saw.
|| [8] Have you considered making a template to be used with a bit
|| incorporating a ball bearing guide?
| That's a possibility.
You're right - that /is/ a big bit to freehand safely (too big for me,
at any rate). If I'm understanding you correctly, I think you'd do
best to cut a template from tempered hardboard and use that in
conjunction with a 1/2" straight (with pilot bearing) bit to shape the
parabolic arch. This should permit a good smooth arch for appearance
and for use as a bearing surface for a second pass with an ogee bit
(again, with a pilot bearing).
In my shop I'd cut this arch on a CNC router - but I'd still do it
with the same two passes with a straight bit and an ogee bit. The only
difference would be that I wouldn't (couldn't) use bits with pilot
bearings. A 1/4" tempered hardboard template is fairly easy to cut and
is inexpensive. If you can, cut it just a "skosh" large and use a
sanding block to produce a smooth, true edge - it'll be less work than
truing the 1" workpiece.
Oh yes (I almost forgot to mention) - I've used carpet tape (kind of a
web with adhesive on both sides - available from lumber yard or
hardware store) to fasten templates to workpieces for this kind of
operation. Remove tape gently (solvent may help) so as not to tear
fibers from the face of your soft cedar.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/solar.html
With a 2-3/4" Bit? By hand? On the end of a long lever (edge guide)? I
wouldn't try it.
"Steve Peterson" <[email protected]> wrote in message
news:[email protected]...
> Do you have a fence for your router? If so, use it with a curved piece
that
> matches the curve of the arch. Use it to follow the curve of the arch, in
> incremental cuts. Slow down the router, if you can. Good luck.
>
> Steve
>
> "tom" <[email protected]> wrote in message
> news:[email protected]...
> > It's possible, but I think it'll get a little scary at the ends of your
> > stock, without both fences in play. Maybe rough cut the stock extra
> > long/wide to avoid the teetering, and give your fingers some extra
> > room? Is there a bearing somewhere on this bit? Tom
> >
>
Do you have a fence for your router? If so, use it with a curved piece that
matches the curve of the arch. Use it to follow the curve of the arch, in
incremental cuts. Slow down the router, if you can. Good luck.
Steve
"tom" <[email protected]> wrote in message
news:[email protected]...
> It's possible, but I think it'll get a little scary at the ends of your
> stock, without both fences in play. Maybe rough cut the stock extra
> long/wide to avoid the teetering, and give your fingers some extra
> room? Is there a bearing somewhere on this bit? Tom
>
[email protected] (in
[email protected]) said:
| Hi all,
|
| I have an upcoming project that's still in the "thinking stage",
| which is to say that I'm trying yo figure out all of the operations
| that I'll need to do and finding ways to do it with my existing
| skills and equipment.
|
| I'm using a large ogee bit (1 3/8" radius) to creat a moulding
| effect. So far I've done this exclusively on straight stock using
| the router table. The upcoming project will need the same moulding
| edge on an arched panel. This bit is large, almost like a panel
| bit, plus I have very little experience routing freehand so I don't
| think that's a viable option.
|
| I'm thinking that I could do this on the table if I position the
| fence such that the curve of the piece indexes on the inside edges
| of the split fence. i.e. "bridging the gap" with the bit inside the
| gap as would be normal. I could easily adjust the depth of cut for
| multiple passes and could still use a featherboardd to provide
| downward pressure. I would still have to "freehand" the work
| maintaining pressure towards the fence.
|
| Any thoughts on this technique or alternate ideas?
There's some important information you didn't provide:
[1] Is arch circular?
[2] Width and height of arch?
[3] Material to be routed?
[4] Thickness of stock to be routed?
[5] Are you routing inside, outside, or both curves?
[6] What does "existing skills and equipment" mean?
[7] Can you pre-cut the desired arch with a band saw and/or straight
router bit?
[8] Have you considered making a template to be used with a bit
incorporating a ball bearing guide?
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/solar.html
Like this: http://www.woodsmith.com/main/ws145toc.html
or
http://store.yahoo.com/backissuesstore/wsback67.html
(no longer available)
I know the #67 copy uses a template to cut out the arch.
[email protected] wrote:
> It will actually be half an arch, because two mirror-image pieces will
> comprise the full arch (spaced apart slightly). Each half will be about
> 24" long.
>
> Imagine the board laying flat against the wall. I'll describe the
> left-hand piece. The bottom will be straight (24") and right-hand edge
> will be straight (6") and the arched top will curve from the top right
> down to a point on the bottom left. There is no left edge because the
> arched top meets the bottom edge on the left. The arch is quite
> gradual.
>
> Tom
>
On 25 Sep 2005 09:52:12 -0700, [email protected] wrote:
>Hi all,
>
>I have an upcoming project that's still in the "thinking stage", which
>is to say that I'm trying yo figure out all of the operations that I'll
>need to do and finding ways to do it with my existing skills and
>equipment.
>
>I'm using a large ogee bit (1 3/8" radius) to creat a moulding effect.
>So far I've done this exclusively on straight stock using the router
>table. The upcoming project will need the same moulding edge on an
>arched panel. This bit is large, almost like a panel bit, plus I have
>very little experience routing freehand so I don't think that's a
>viable option.
>
>I'm thinking that I could do this on the table if I position the fence
>such that the curve of the piece indexes on the inside edges of the
>split fence. i.e. "bridging the gap" with the bit inside the gap as
>would be normal. I could easily adjust the depth of cut for multiple
>passes and could still use a featherboardd to provide downward
>pressure. I would still have to "freehand" the work maintaining
>pressure towards the fence.
>
>Any thoughts on this technique or alternate ideas?
>
>Thanks,
>Tom
make a curved fence.
I think everybody needs to know the length of the arch and
the degree of the arch if possible.
There are several methods to make arched molding, and some
are easier than others. The length of the piece is a
"must have" before folks can be more helpful.
[email protected] wrote:
> Hi all,
>
> I have an upcoming project that's still in the "thinking stage", which
> is to say that I'm trying yo figure out all of the operations that I'll
> need to do and finding ways to do it with my existing skills and
> equipment.
>
> I'm using a large ogee bit (1 3/8" radius) to creat a moulding effect.
> So far I've done this exclusively on straight stock using the router
> table. The upcoming project will need the same moulding edge on an
> arched panel. This bit is large, almost like a panel bit, plus I have
> very little experience routing freehand so I don't think that's a
> viable option.