Hello,
I had an unfortunate accident where I dropped the motor from my Delta
table saw (1 1/2 hp contractor saw 36-444) on the floor in the shop. I
dropped it on the opposite end to the shaft/pulley. Now I have an
issue with the motor. With the motor attached to the back of the table
saw, when I place the belt on the pulley, and power on the saw (as in
normal operation), the motor won't spin up and the protective circuit
on the motor trips. However, with no load on the motor, it will power
on and spin up with no problem.
I am able to use the saw by powering on the motor and letting it spin
up to speed, then slowly lowering it onto the belt. The saw cuts wood
with no problem once the motor has come up to speed.
Does anyone know what part of the motor got damaged when I dropped it
that would cause this behavior?
Thanks very much.
RCP127 wrote:
> Hello,
>
> I had an unfortunate accident where I dropped the motor from my Delta
> table saw (1 1/2 hp contractor saw 36-444) on the floor in the shop. I
> dropped it on the opposite end to the shaft/pulley. Now I have an
> issue with the motor. With the motor attached to the back of the table
> saw, when I place the belt on the pulley, and power on the saw (as in
> normal operation), the motor won't spin up and the protective circuit
> on the motor trips. However, with no load on the motor, it will power
> on and spin up with no problem.
>
> I am able to use the saw by powering on the motor and letting it spin
> up to speed, then slowly lowering it onto the belt. The saw cuts wood
> with no problem once the motor has come up to speed.
>
> Does anyone know what part of the motor got damaged when I dropped it
> that would cause this behavior?
>
> Thanks very much.
>
Does the motor have an external fan? If so, you can remove
the fan housing on that end and check for something binding.
Sometimes the fan will get knocked so that it rubs the
housing. Without the belt attached, can you feel friction
when the shaft is turned?
--
Gerald Ross
Cochran, GA
Chaste makes waste.
----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
I don't think that is the problem or it would make noise once it is running.
I think that either you damaged the capacitor, a wire came loose from the
capacitor, or if it is a RI motor the brush plate inside moved. If you take
the end bell off and there is a plate that can rotate when loosened, you
have to realign the marks.
max
> RCP127 wrote:
>
>> Hello,
>>
>> I had an unfortunate accident where I dropped the motor from my Delta
>> table saw (1 1/2 hp contractor saw 36-444) on the floor in the shop. I
>> dropped it on the opposite end to the shaft/pulley. Now I have an
>> issue with the motor. With the motor attached to the back of the table
>> saw, when I place the belt on the pulley, and power on the saw (as in
>> normal operation), the motor won't spin up and the protective circuit
>> on the motor trips. However, with no load on the motor, it will power
>> on and spin up with no problem.
>>
>> I am able to use the saw by powering on the motor and letting it spin
>> up to speed, then slowly lowering it onto the belt. The saw cuts wood
>> with no problem once the motor has come up to speed.
>>
>> Does anyone know what part of the motor got damaged when I dropped it
>> that would cause this behavior?
>>
>> Thanks very much.
>>
>
> Does the motor have an external fan? If so, you can remove
> the fan housing on that end and check for something binding.
> Sometimes the fan will get knocked so that it rubs the
> housing. Without the belt attached, can you feel friction
> when the shaft is turned?
"max" writes:
> I don't think that is the problem or it would make noise once it is
running.
> I think that either you damaged the capacitor, a wire came loose from the
> capacitor, or if it is a RI motor the brush plate inside moved. If you
take
> the end bell off and there is a plate that can rotate when loosened, you
> have to realign the marks.
I agree.
If you are unfamiliar with doing motor repair, take it to a motor rewind
shop and have them check it out.
You are probably looking at the minimum charge to get the motor inspected
and repaired.
BTW, start saving your pennies for a new motor.
Took me less than 6 months to burn up that cap start, cap run motor supplied
as original equipment.
HTH
Lew