I need to make a lot of small hourglass-shaped rollers and I don't
have a lathe. The finished roller will be 3/4" long, 3/4" outer
diameter, and taper in about 3/32", so a net 9/16" diam at the middle,
if I have the math right.
I am thinking of starting with a 3/4" diam dowel and then using a
router with a core box bit
http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/bt_core.html
maybe 1 1/2" diameter. I think that geometry about works, and
precision is not critical. I'd run a bunch of profiles and then chop
them off at 3/4" lengths.
Does this sound workable and safe? Alternate suggestions? Any tips
for how to secure the dowel, start the cut, and rotate the dowel?
While I am fine with some shop tools (TS, DP), I am a router newbie.
OTOH, if anyone knows where I can buy such things ready-made in wood
or plastic or even rubber (no luck at McMaster-Carr), please let me
know. I think such things exist, but I don't even know what they are
called.
TIA. -- Jesse
On May 14, 9:21=A0pm, Jesse <[email protected]> wrote:
> I need to make a lot of small hourglass-shaped rollers and I don't
> have a lathe. =A0The finished roller will be 3/4" long, 3/4" outer
> diameter, and taper in about 3/32", so a net 9/16" diam at the middle,
> if I have the math right.
>
> I am thinking of starting with a 3/4" diam dowel and then using a
> router with a core box bithttp://www.mlcswoodworking.com/shopsite_sc/store=
/html/smarthtml/pages...
> maybe 1 1/2" diameter. =A0I think that geometry about works, and
> precision is not critical. =A0I'd run a bunch of profiles and then chop
> them off at 3/4" lengths.
>
> Does this sound workable and safe? =A0Alternate suggestions? Any tips
> for how to secure the dowel, start the cut, and rotate the dowel?
> While I am fine with some shop tools (TS, DP), I am a router newbie. =A0
>
> OTOH, if anyone knows where I can buy such things ready-made in wood
> or plastic or even rubber (no luck at McMaster-Carr), please let me
> know. =A0I think such things exist, but I don't even know what they are
> called. =A0
>
> TIA. -- Jesse
Do you have a drill press?
Might be safer to mount in a drill press and use a file ot 60 grit
sand paper to get your profile..
Randy
http://nokeswoodworks.com
Jesse wrote:
> I need to make a lot of small hourglass-shaped rollers and I don't
> have a lathe. The finished roller will be 3/4" long, 3/4" outer
> diameter, and taper in about 3/32", so a net 9/16" diam at the middle,
> if I have the math right.
>
> I am thinking of starting with a 3/4" diam dowel and then using a
> router with a core box bit
> http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/bt_core.html
> maybe 1 1/2" diameter. I think that geometry about works, and
> precision is not critical. I'd run a bunch of profiles and then chop
> them off at 3/4" lengths.
>
> Does this sound workable and safe? Alternate suggestions? Any tips
> for how to secure the dowel, start the cut, and rotate the dowel?
> While I am fine with some shop tools (TS, DP), I am a router newbie.
I'd probably do what you are thinking. I would...
1. Cut a "V" notch lengthwise into a board to contain the dowel while
allowing it to be rotated.
2. Drill a hole somewhat larger in diameter then the bit thru the board
centered on the "V" groove
3. Rig some sort of moveable stop on the board.
To use...
1. Secure board on router table with bit thru hole
2. Position dowel end stop
3. Turn on router
4. Hold dowel at an angle so end is at the stop but doesn't contact bit
5. Lower dowel to contact bit, hold down with left hand, rotate with right.
6. Reposition stop and repeat.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico