I want to restore the front door on my new house, which at some point
had its external mouldings ripped off and plywood slapped on top.
However I can't find anywhere that sells the bolection moulding with
the right dimensions. Judging from the paint markings on the door, the
moulding needs to cover about 1 inch of the recessed panel, the depth
of which is about 2/3". Does anyone know a UK source which might sell
such a moulding? Or will it probably be necessary to build up something
from two or more mouldings?
Here's a diagram, to be viewed in a monospaced font, showing depth A
(2/3") and coverage distance B (1"), with the rough profile of the
required moulding marked with x's:
xxx
xxxxxxx
========|xxxxxxx
^|xxxxxxxxx
A|xxxxxxxxxxxxx
v|xxxxxxxxxxxxxxxxxx
========================---
< B >
Thanks in advance for any advice.
[email protected] wrote:
> Lobster wrote:
>
>> (I though that was brilliant bit of ASCII-art actually!)
>
> Thanks :)
>
>> Why does the moulding have to be that specific profile? I've restored
>> several doors in the past which have been "Barrybucknellised" like yours
>> in the past; I've just used whatever moulding I could obtain and that
>> looked good.
>
> There's no exact profile I'm after - whatever looks good, but I would
> like a projecting moulding that extends out a bit onto the door
> stiles/rails (called a bolection moulding I believe). Just because
> that's what was there before and it looks a bit more solid than an
> inset moulding, IMO.
OK, I've certainly seen that stuff (projection moulding?) around, but
can't recall exactly where... I'd have guessed at simply somewhere like
B&Q or Wickes, but presumably you've tried them?
Have you looked at the Richard Burbridge range? Might be worth a phone
call:
<http://www.richardburbidge.co.uk/main.asp?page=183>
David
[email protected] wrote:
> I want to restore the front door on my new house, which at some point
> had its external mouldings ripped off and plywood slapped on top.
> However I can't find anywhere that sells the bolection moulding with
> the right dimensions. Judging from the paint markings on the door, the
> moulding needs to cover about 1 inch of the recessed panel, the depth
> of which is about 2/3". Does anyone know a UK source which might sell
> such a moulding? Or will it probably be necessary to build up something
> from two or more mouldings?
>
>
> Here's a diagram, to be viewed in a monospaced font, showing depth A
> (2/3") and coverage distance B (1"), with the rough profile of the
> required moulding marked with x's:
>
> xxx
> xxxxxxx
> ========|xxxxxxx
> ^|xxxxxxxxx
> A|xxxxxxxxxxxxx
> v|xxxxxxxxxxxxxxxxxx
> ========================---
> < B >
>
>
> Thanks in advance for any advice.
>
See a joiner and get a few meters run up.
Stuart wrote:
> Sorry but that doesn't do it for me .Any chance of posting a pic somewhere . I
> know of a place near Glasgow but that might not be practical for you .
Here's a hopefully clearer image:
http://img151.imageshack.us/img151/9930/bolectionmouldingdimensaz2.png
Obviously, the outer profile of the moulding is just roughed in - it's
an illustration of the dimensions that matter for fitting the moulding
on the door. Glasgow would be doable. I dont suppose they have a
website showing available mouldings? :-)
Re: the other suggestion of getting some custom made - neighbours doors
could be used as a template, but I'm concerned that it might be a bit
expensive to go down that route.
An alternative would be to form the moulding from two pieces (see red
line on diagram). Might be easier to do and give more flexibility in
choosing profiles to combine.
Lobster wrote:
> (I though that was brilliant bit of ASCII-art actually!)
Thanks :)
> Why does the moulding have to be that specific profile? I've restored
> several doors in the past which have been "Barrybucknellised" like yours
> in the past; I've just used whatever moulding I could obtain and that
> looked good.
There's no exact profile I'm after - whatever looks good, but I would
like a projecting moulding that extends out a bit onto the door
stiles/rails (called a bolection moulding I believe). Just because
that's what was there before and it looks a bit more solid than an
inset moulding, IMO.
I might end up applying an inset moulding that's flush with the door
stile/rail, and then cap the join with another moulding. Achieves the
same ultimate effect, but with a bit more hassle.
It's interesting to see how the detailing in my new house varies
according to how visible it is to 'the public', so cornicing is
fanciest in the sitting room - where the door has bolection mouldings,
and elsewhere the cornicing gets less ornate, and doors get inset
mouldings. Victorians were clearly a bunch of cheapskates interested in
spending as little as possible to project an image of wealth. :)
Stuart wrote:
> Here is a pic of the profile of the moulding I used .
>
> http://img.photobucket.com/albums/v487/molley/Moulding/IMG_6226.jpg
>
> It's 37mm x 20mm with a bit that overhangs ( the red part) that is 5mm wide .
> The bit below the red part is about 12mm deep
> The company is Express Timber Products of Abercorn Street,Paisley .Tel 0141
> 848 0102 . I don't think they have a website .
> As I said in an e-mail if you want a sample of this particular moulding posted
> to you let me know .
> cheers
> Stuart .
Thanks Stuart, but in this case the rebate depth (12mm) would be too
shallow for it to be suitable by itself. Perhaps it could be packed out
underneath to raise it to the full 2/3 inch or so.
I did already find a bolection/raised panel moulding at 'Build Center'
but the dimensions were not right.
Stuart wrote:
> A suitable thickess piece of timber would do the job I'm sure . How many mm do
> you mean by 2/3rd inch ?
That was the closest imperial measurement to the mm measurement that I
made. Since it's Victorian the original moulding would have been in
inches. After perusing the internets it looks like it might be 11/16"
as that is a measurement which crops up in moulding dimensions.
Alternatively it could be 3/4" and I've not measured it accurately!
It's looking like an off-the-shelf solution is probably not available,
but building up from more than one piece is more 'interesting' anyway,
so no worries.
The moulding I found at Build Center (sic) has a rebate of 12mm depth.
Get 4mm stripwood... buy router table... increase rebate depth... put
nice edge on stripwood... This option has the benefit of making me buy
a router table.
Lobster wrote:
> OK, I've certainly seen that stuff (projection moulding?) around, but
> can't recall exactly where... I'd have guessed at simply somewhere like
> B&Q or Wickes, but presumably you've tried them?
Either they didnt stock any such moulding, or they did, but with the
wrong dimensions, IIRC.
> Have you looked at the Richard Burbridge range? Might be worth a phone
> call:
Thanks, I'll try that - it would be useful if they had an online
brochure of their range.
[email protected] wrote:
> Thanks in advance for any advice.
Many thanks to everyone who took the time to reply.
It seems that the possible answers are:
1) Keep looking at retailers for a moulding with the right dimensions
2) Build something up from 2+ pieces, maybe with some modifications.
3) Get a joiner to run up a custom-made batch of moulding
4) "Dado Rail"
On 2006-12-05 10:50:41 +0000, [email protected] said:
> I want to restore the front door on my new house, which at some point
> had its external mouldings ripped off and plywood slapped on top.
> However I can't find anywhere that sells the bolection moulding with
> the right dimensions. Judging from the paint markings on the door, the
> moulding needs to cover about 1 inch of the recessed panel, the depth
> of which is about 2/3". Does anyone know a UK source which might sell
> such a moulding? Or will it probably be necessary to build up something
> from two or more mouldings?
>
>
> Here's a diagram, to be viewed in a monospaced font, showing depth A
> (2/3") and coverage distance B (1"), with the rough profile of the
> required moulding marked with x's:
>
> xxx
> xxxxxxx
> ========|xxxxxxx
> ^|xxxxxxxxx
> A|xxxxxxxxxxxxx
> v|xxxxxxxxxxxxxxxxxx
> ========================---
> < B >
>
>
> Thanks in advance for any advice.
The best solution for this would be to take a sample or a dimensioned
drawing to a joinery firm and ask them to run the section for you on a
spindle moulder.
For a short run like this, tooling could be made for £20-30 to work
with a universal cutter block
Look at
http://www.wealdentool.com/acatalog/Spindle_Tooling_91.html
as an example. A joinery firm should have the blocks already and will
be able to have knives made quite easily from a sample of the profile
or the drawing.
<[email protected]> wrote in message
news:[email protected]...
>I want to restore the front door on my new house, which at some point
> had its external mouldings ripped off and plywood slapped on top.
Try
Thames Moulding Co
16b Whytecliffe Rd South
Purley Surrey CR8 2AU
Tel: 020 8668 0332
Their catalogue shows 21 bolections.
Toby
Stuart wrote:
> On 5 Dec 2006 02:50:41 -0800, [email protected] wrote:
>
>> I want to restore the front door on my new house, which at some point
>> had its external mouldings ripped off and plywood slapped on top.
>> However I can't find anywhere that sells the bolection moulding with
>> the right dimensions. Judging from the paint markings on the door, the
>> moulding needs to cover about 1 inch of the recessed panel, the depth
>> of which is about 2/3". Does anyone know a UK source which might sell
>> such a moulding? Or will it probably be necessary to build up something
>>from two or more mouldings?
>
> Sorry but that doesn't do it for me .Any chance of posting a pic somewhere . I
> know of a place near Glasgow but that might not be practical for you .
(I though that was brilliant bit of ASCII-art actually!)
Why does the moulding have to be that specific profile? I've restored
several doors in the past which have been "Barrybucknellised" like yours
in the past; I've just used whatever moulding I could obtain and that
looked good.
David
On 5 Dec 2006 02:50:41 -0800, [email protected] wrote:
>I want to restore the front door on my new house, which at some point
>had its external mouldings ripped off and plywood slapped on top.
>However I can't find anywhere that sells the bolection moulding with
>the right dimensions. Judging from the paint markings on the door, the
>moulding needs to cover about 1 inch of the recessed panel, the depth
>of which is about 2/3". Does anyone know a UK source which might sell
>such a moulding? Or will it probably be necessary to build up something
>from two or more mouldings?
Well, I'm not in the UK, but I've been known to give a good price for
millwork from time to time. If you're willing to pay for overseas
shipping, I imagine I could make you a set of door moulding from any
US domestic hardwood for much less than you might expect (our wood is
not quite as expensive over here, and a door's worth of moulding in
that profile wouldn't take me long at all.)
So if you can't find anything on your side of the big pond, e-mail me
at prometheus<at>charter.net, and I'll work you up a quote.
On 5 Dec 2006 10:09:58 -0800, [email protected] wrote:
>
>Stuart wrote:
>
>> Here is a pic of the profile of the moulding I used .
>>
>> http://img.photobucket.com/albums/v487/molley/Moulding/IMG_6226.jpg
>>
>> It's 37mm x 20mm with a bit that overhangs ( the red part) that is 5mm wide .
>> The bit below the red part is about 12mm deep
>> The company is Express Timber Products of Abercorn Street,Paisley .Tel 0141
>> 848 0102 . I don't think they have a website .
>> As I said in an e-mail if you want a sample of this particular moulding posted
>> to you let me know .
>> cheers
>> Stuart .
>
>Thanks Stuart, but in this case the rebate depth (12mm) would be too
>shallow for it to be suitable by itself. Perhaps it could be packed out
>underneath to raise it to the full 2/3 inch or so.
>I did already find a bolection/raised panel moulding at 'Build Center'
>but the dimensions were not right.
A suitable thickess piece of timber would do the job I'm sure . How many mm do
you mean by 2/3rd inch ?
S
On 5 Dec 2006 02:50:41 -0800, [email protected] wrote:
>I want to restore the front door on my new house, which at some point
>had its external mouldings ripped off and plywood slapped on top.
>However I can't find anywhere that sells the bolection moulding with
>the right dimensions. Judging from the paint markings on the door, the
>moulding needs to cover about 1 inch of the recessed panel, the depth
>of which is about 2/3". Does anyone know a UK source which might sell
>such a moulding? Or will it probably be necessary to build up something
>from two or more mouldings?
>
>
>Here's a diagram, to be viewed in a monospaced font, showing depth A
>(2/3") and coverage distance B (1"), with the rough profile of the
>required moulding marked with x's:
>
> xxx
> xxxxxxx
>========|xxxxxxx
> ^|xxxxxxxxx
> A|xxxxxxxxxxxxx
> v|xxxxxxxxxxxxxxxxxx
> ========================---
> < B >
>
>
>Thanks in advance for any advice.
Sorry but that doesn't do it for me .Any chance of posting a pic somewhere . I
know of a place near Glasgow but that might not be practical for you .
[email protected] wrote:
> [email protected] wrote:
>> Thanks in advance for any advice.
>
> Many thanks to everyone who took the time to reply.
> It seems that the possible answers are:
>
> 1) Keep looking at retailers for a moulding with the right dimensions
Yes, but timber merchants rather than sheds or BMs. You're more likely
to find it in a posh area where big front doors are the norm
> 2) Build something up from 2+ pieces, maybe with some modifications.
For exterior, probably not a good idea. The smaller the section, the
quicker it rots
> 3) Get a joiner to run up a custom-made batch of moulding
Very expensive for one door, and you're not trying to match anything
exactly.
> 4) "Dado Rail"
Doesn't matter what the moulding is called. Sounds like depth is the key
dimension for you, so just look for something close.
On 5 Dec 2006 05:21:47 -0800, [email protected] wrote:
>Stuart wrote:
>> Sorry but that doesn't do it for me .Any chance of posting a pic somewhere . I
>> know of a place near Glasgow but that might not be practical for you .
>
>Here's a hopefully clearer image:
>
>http://img151.imageshack.us/img151/9930/bolectionmouldingdimensaz2.png
>
>Obviously, the outer profile of the moulding is just roughed in - it's
>an illustration of the dimensions that matter for fitting the moulding
>on the door. Glasgow would be doable. I dont suppose they have a
>website showing available mouldings? :-)
>
>
Here is a pic of the profile of the moulding I used .
http://img.photobucket.com/albums/v487/molley/Moulding/IMG_6226.jpg
It's 37mm x 20mm with a bit that overhangs ( the red part) that is 5mm wide .
The bit below the red part is about 12mm deep
The company is Express Timber Products of Abercorn Street,Paisley .Tel 0141
848 0102 . I don't think they have a website .
As I said in an e-mail if you want a sample of this particular moulding posted
to you let me know .
cheers
Stuart .
Lobster wrote:
> [email protected] wrote:
>> Lobster wrote:
>>
>>> (I though that was brilliant bit of ASCII-art actually!)
>>
>> Thanks :)
>>
>>> Why does the moulding have to be that specific profile? I've restored
>>> several doors in the past which have been "Barrybucknellised" like yours
>>> in the past; I've just used whatever moulding I could obtain and that
>>> looked good.
>>
>> There's no exact profile I'm after - whatever looks good, but I would
>> like a projecting moulding that extends out a bit onto the door
>> stiles/rails (called a bolection moulding I believe). Just because
>> that's what was there before and it looks a bit more solid than an
>> inset moulding, IMO.
>
> OK, I've certainly seen that stuff (projection moulding?) around, but
> can't recall exactly where... I'd have guessed at simply somewhere like
> B&Q or Wickes, but presumably you've tried them?
>
> Have you looked at the Richard Burbridge range? Might be worth a phone
> call:
> <http://www.richardburbidge.co.uk/main.asp?page=183>
>
> David
All the major merchants do their own range of mouldings. Travis Perkins
etc. Depends who's in your area
On 6 Dec 2006 02:52:07 -0800, [email protected] wrote:
>Stuart wrote:
>> A suitable thickess piece of timber would do the job I'm sure . How many mm do
>> you mean by 2/3rd inch ?
>
>That was the closest imperial measurement to the mm measurement that I
>made. Since it's Victorian the original moulding would have been in
>inches. After perusing the internets it looks like it might be 11/16"
>as that is a measurement which crops up in moulding dimensions.
>Alternatively it could be 3/4" and I've not measured it accurately!
>It's looking like an off-the-shelf solution is probably not available,
>but building up from more than one piece is more 'interesting' anyway,
>so no worries.
>The moulding I found at Build Center (sic) has a rebate of 12mm depth.
>Get 4mm stripwood... buy router table... increase rebate depth... put
>nice edge on stripwood... This option has the benefit of making me buy
>a router table.
LOL...Just because the original was made in Imperial doesn't mean you have to
measure it now in that .LOL
Building the moulding from more than one piece might well be more interesting
when you only have one door to do but luckily the moulding I have fitted my
doors and I had 9 door sides to do ,each with 4 panels ( 16 mitres to each
door).
I reckon you should use a "near enough" moulding like the one I suggested and
slip a thin piece of wood beneath to give you the correct depth of the recessed
part. No point in giving yourself unnecessary work or causing you additional
expense.
Stuart