On Sat, 27 Jan 2007 20:36:20 +0000 (UTC), Bruce Barnett
<[email protected]> wrote:
>"EWCM" <[email protected]> writes:
>
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>
>While there, I noticed this one on a guy assembling his own Stonehenge
>using no machinery - not even a pulley - solo.
>
>http://www.youtube.com/watch?v=lRRDzFROMx0
What!? You mean it wasn't aliens with anti-gravity rays? Next you'll be
telling us that the ancient Egyptians understood the principles of rollers,
pulleys, and leverage.
+--------------------------------------------------------------------------------+
If you're gonna be dumb, you better be tough
+--------------------------------------------------------------------------------+
And you wonder why there are so many safty stickers on tools!
"EWCM" <[email protected]> wrote in message
news:[email protected]...
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
>
I did not read most of the other posts but this is dangerous, no
question about it. However, I used to start my neighbors concrete
mixer - belt driven - by rotating the drum and then flipping the
switch. Otherwise the motor just hummed. It would run empty but this
method was necessary when components where in the drum.
Marc
On Jan 26, 5:05 pm, "EWCM" <[email protected]> wrote:
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
On Jan 26, 2:05 pm, "EWCM" <[email protected]> wrote:
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an old Craftsman saw with a bad starter cap.
Not really. The early scene shows the motor, the rotor clearly has
a centrifugal switch built in. He just has a bit of dirt/sawdust
in the start switch contacts. If he finds them, and burnishes them,
like by rubbing with a strip of paper, it all starts working like new.
It isn't a capacitor-start motor.
As for the bad bearing, perhaps that's a misattribution of
dried out grease, which can be fixed with solvent/heat and new grease).
In article <[email protected]>, J. Clarke <[email protected]> wrote:
>On Sun, 28 Jan 2007 04:21:04 GMT, "CW" <[email protected]> wrote:
>
>>Recent findings are that they understood how to make and pour concrete.
>
>Considering that the last Pharaoh was doing some guy named Caesar and
>the Romans most assuredly knew concrete (knew something we don't
>apparently if the longevity of their concrete structures vs ours is
>any indicator) it seems very likely that the Egyptians if they didn't
>know before picked it up from the Romans.
>
My guess is it may have been the other way around.
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.
"EWCM" <[email protected]> wrote in message
news:[email protected]...
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
And the chance for disaster continues with his practice of crosscutting with
the board against the fence.
Dumb & dumber.
Max
On Sat, 27 Jan 2007 15:52:13 GMT, tomcarlson(REMOVE)@sbcglobal.net
(Tom) wrote:
>On Fri, 26 Jan 2007 17:05:09 -0500, "EWCM" <[email protected]>
>wrote:
>
>>http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>>This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>>with disaster as he starts it.
>>
>I think he should just crank the blade all the way up, spin it as fast
>as he can by hand then kick in the motor. If it doesn't catch, he can
>keep spinning until it does. If he's pretty quick he shouldn't lose
>too much blood and meat.
He should just hit the power _then_ give it a spin. (How did I _ever_
survive my youth?)
"Mark & Juanita" <[email protected]> wrote in message
news:[email protected]...
>
> Second, cross-cutting with a rip fence. If this were a higher powered
> saw, there is absolutely no doubt that the danger of kickback and other
> disaster is way high, especially with no splitter. However, this is a
> small, 40-year old Craftsman table-top table saw (My dad has an
equivalent
> 60+ year old Wards PowerKraft saw). These saws are tremendously
> low-powered, as you can hear as he is trying to cut that piece of plywood.
It looked to me to be a Craftsman Model 10 which is neither small (10"), nor
were they under powered, even with the original motors. That said, I
largely agree with the intent of your post Mark. As I watched the video, it
just was not clear to me that the plywood was up against the fence. Just
could not tell from the video. If it was, it's unlikely the cutoff would
have simply laid there as it did. I suspect the fence was over to the right
side of the table and the wood was not really up against it.
> Kickback is highly unlikely -- what is going to happen is he is going to
> jam the blade and stall the motor.
I'd disagree with you on this point Mark. Kickback could be very likely
even with an underpowered motor. He never stalled the saw and as long as
the blade is spinning at speed or near speed, kickback from pinching the
wood into the rising teeth is likely. That said - I'll repeat myself by
saying I'm not sure that was really a problem or a potential for this
fellow.
--
-Mike-
[email protected]
On Fri, 26 Jan 2007 17:05:09 -0500, "EWCM" <[email protected]>
wrote:
>http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
>This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>with disaster as he starts it.
>
I think he should just crank the blade all the way up, spin it as fast
as he can by hand then kick in the motor. If it doesn't catch, he can
keep spinning until it does. If he's pretty quick he shouldn't lose
too much blood and meat.
On Fri, 26 Jan 2007 17:05:09 -0500, "EWCM" <[email protected]>
wrote:
>http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
>This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>with disaster as he starts it.
>
This guy is going to have a very serious accident in the not too
distant future. He must be bucking for a Darwin Award.
"EWCM" <[email protected]> wrote in message
news:[email protected]...
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
Why would he post the video? Is he proud of his accomplishment?
"George Max" wrote in message
> On Sat, 27 Jan 2007 11:31:20 -0500, J. Clarke
> wrote:
>
> >
> >He should just hit the power _then_ give it a spin. (How did I _ever_
> >survive my youth?)
>
> Thinking back, how did *any* of us survive our youth?
At 64, it's too early to be making predictions.
--
www.e-woodshop.net
Last update: 1/06/07
Recent findings are that they understood how to make and pour concrete.
"Mark & Juanita" <[email protected]> wrote in message
news:[email protected]...
> Next you'll be
> telling us that the ancient Egyptians understood the principles of
rollers,
> pulleys, and leverage.
>
On Sat, 27 Jan 2007 11:31:20 -0500, J. Clarke <[email protected]>
wrote:
>
>He should just hit the power _then_ give it a spin. (How did I _ever_
>survive my youth?)
Thinking back, how did *any* of us survive our youth?
On Sat, 27 Jan 2007 20:36:20 +0000 (UTC), Bruce Barnett
<[email protected]> wrote:
>"EWCM" <[email protected]> writes:
>
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>
>While there, I noticed this one on a guy assembling his own Stonehenge
>using no machinery - not even a pulley - solo.
>
>http://www.youtube.com/watch?v=lRRDzFROMx0
Dayum! I thought that I knew how to move stuff. That's impressive as
Hell. Did you check out his Web site
<http://www.theforgottentechnology.com/>?
"Mark & Juanita" <[email protected]> wrote in message
news:[email protected]...
Snip
>
> Second, cross-cutting with a rip fence. If this were a higher powered
> saw, there is absolutely no doubt that the danger of kickback and other
> disaster is way high, especially with no splitter. However, this is a
> small, 40-year old Craftsman table-top table saw (My dad has an
> equivalent
> 60+ year old Wards PowerKraft saw). These saws are tremendously
> low-powered, as you can hear as he is trying to cut that piece of plywood.
> Kickback is highly unlikely --
Wrong! Just as likely as with any other saw used in this manor. Power has
nothing to do with the likely hood of kick back.
"Mark & Juanita" <[email protected]> wrote in message
news:[email protected]...
>
> What!? You mean it wasn't aliens with anti-gravity rays? Next you'll
be
> telling us that the ancient Egyptians understood the principles of
rollers,
> pulleys, and leverage.
>
That's just too far fetched. I'm sticking with the alien theory.
--
-Mike-
[email protected]
Hopefully the daughter is not in the same room with him and the table saw.
Its so bad I wonder if its an act and he's just trying to look
dumb/dangerous and stir up some reaction !
"Leuf" <[email protected]> wrote in message
news:[email protected]...
> On Fri, 26 Jan 2007 22:18:38 GMT, "Max"
> <[email protected]> wrote:
>>
>>"EWCM" <[email protected]> wrote in message
>>news:[email protected]...
>>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>>
>>> This guy has an olf Craftsman saw with a bad starter cap. Watch him
>>> flirt
>>> with disaster as he starts it.
>>
>>And the chance for disaster continues with his practice of crosscutting
>>with
>>the board against the fence.
>>Dumb & dumber.
>
> I hope he's at least had the foresight to teach his daughter how to
> dial 911..
>
>
> -Leuf
On Sun, 28 Jan 2007 04:21:04 GMT, "CW" <[email protected]> wrote:
>Recent findings are that they understood how to make and pour concrete.
Considering that the last Pharaoh was doing some guy named Caesar and
the Romans most assuredly knew concrete (knew something we don't
apparently if the longevity of their concrete structures vs ours is
any indicator) it seems very likely that the Egyptians if they didn't
know before picked it up from the Romans.
>"Mark & Juanita" <[email protected]> wrote in message
>news:[email protected]...
>> Next you'll be
>> telling us that the ancient Egyptians understood the principles of
>rollers,
>> pulleys, and leverage.
>>
>
On Fri, 26 Jan 2007 23:48:51 GMT, "Toller" <[email protected]> wrote:
>
>"EWCM" <[email protected]> wrote in message
>news:[email protected]...
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>Why would he post the video? Is he proud of his accomplishment?
If you look at his other videos you can watch him try to frame a wall.
He's apparently just recording the progress of his project, but in
video instead of the pictures.
-Leuf
On Sat, 27 Jan 2007 08:54:16 -0500, "Mike Marlow" <[email protected]>
wrote:
... snip
>
>
>> Kickback is highly unlikely -- what is going to happen is he is going to
>> jam the blade and stall the motor.
>
>I'd disagree with you on this point Mark. Kickback could be very likely
>even with an underpowered motor. He never stalled the saw and as long as
>the blade is spinning at speed or near speed, kickback from pinching the
>wood into the rising teeth is likely. That said - I'll repeat myself by
>saying I'm not sure that was really a problem or a potential for this
>fellow.
I'll retract that part of my comment.
+--------------------------------------------------------------------------------+
If you're gonna be dumb, you better be tough
+--------------------------------------------------------------------------------+
In article <[email protected]>, "Max" <[email protected]> wrote:
>
>"EWCM" <[email protected]> wrote in message
>news:[email protected]...
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>
>And the chance for disaster continues with his practice of crosscutting with
>the board against the fence.
>Dumb & dumber.
No ear or eye protection either. Wearing sandals besides.
What a dummy.
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.
On Fri, 26 Jan 2007 22:18:38 GMT, "Max" <[email protected]>
wrote:
>
>"EWCM" <[email protected]> wrote in message
>news:[email protected]...
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>
>And the chance for disaster continues with his practice of crosscutting with
>the board against the fence.
>Dumb & dumber.
>
>Max
>
Let's look at this a little closer.
First, his starting method -- it ain't pretty, but I think you are
assigning way more hysteria to it than the situation warrants. Possible
failure mechanisms? 1) bucket falls down, motor falls onto belt, motor
fails to start. 2) foot slips on outside shaft -- motor fails to start 3)
He screws up and pliers hits pulley, pulley pulls pliers away from him,
smacks plier inside table saw. Of all the scenarios, this has the most
possibility for disaster by having stuff thrown back at him, but that's
pretty low probability. The way his is holding the pliers shows that he
isn't going to get grabbed with the pliers, they will be pulled from his
hand. As I said, it's not pretty, but it's not going to turn him into a
quadrapalegic either.
Second, cross-cutting with a rip fence. If this were a higher powered
saw, there is absolutely no doubt that the danger of kickback and other
disaster is way high, especially with no splitter. However, this is a
small, 40-year old Craftsman table-top table saw (My dad has an equivalent
60+ year old Wards PowerKraft saw). These saws are tremendously
low-powered, as you can hear as he is trying to cut that piece of plywood.
Kickback is highly unlikely -- what is going to happen is he is going to
jam the blade and stall the motor. One of the dangers of these small saws
is that people get used to using them with all of their warts, including
stalling the blade when doing something dumb. Then they buy a
higher-powered saw, use the same techniques and wind up with real kickback.
That said, for this particular case, this is really not going to result in
bad things happening on *that* particular saw as long as the guy maintains
a strong grip.
Finally, yep not using hearing protection is a bad idea, and he will most
likely pay for that down the road. OTOH, there are car stereo systems out
there that put out more dB sound than that tablesaw.
In short, this video is certainly not a safety campaign poster example,
but it is not the spinning blades o' death folks are making it out to be.
Would I do those things? Nope, nor would I recommend them. However, I'm
not going to get spun up in a tizzy over them either.
+--------------------------------------------------------------------------------+
If you're gonna be dumb, you better be tough
+--------------------------------------------------------------------------------+
That idiot is fortunate beyond belief! Good thing the cut off piece didn't
jam between the blade and the fence fly back and knock his daughter out
cold!
"EWCM" <[email protected]> wrote in message
news:[email protected]...
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
>
>
On Fri, 26 Jan 2007 22:18:38 GMT, "Max"
<[email protected]> wrote:
>
>"EWCM" <[email protected]> wrote in message
>news:[email protected]...
>> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>>
>> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
>> with disaster as he starts it.
>
>And the chance for disaster continues with his practice of crosscutting with
>the board against the fence.
>Dumb & dumber.
I hope he's at least had the foresight to teach his daughter how to
dial 911..
-Leuf
"EWCM" <[email protected]> writes:
> http://www.youtube.com/watch?v=Yp-bQQl3FWY
>
> This guy has an olf Craftsman saw with a bad starter cap. Watch him flirt
> with disaster as he starts it.
While there, I noticed this one on a guy assembling his own Stonehenge
using no machinery - not even a pulley - solo.
http://www.youtube.com/watch?v=lRRDzFROMx0
--
Sending unsolicited commercial e-mail to this account incurs a fee of
$500 per message, and acknowledges the legality of this contract.
"Mike Marlow" <[email protected]> wrote in message
news:[email protected]...
>
> It looked to me to be a Craftsman Model 10 which is neither small (10"),
> nor
> were they under powered, even with the original motors. That said, I
> largely agree with the intent of your post Mark. As I watched the video,
> it
> just was not clear to me that the plywood was up against the fence. Just
> could not tell from the video. If it was, it's unlikely the cutoff would
> have simply laid there as it did. I suspect the fence was over to the
> right
> side of the table and the wood was not really up against it.
I wondered the same thing about the fence. However, the way he had to pull
the piece off the end of the saw after the cut made me think he was up
against the fence... the whole thing was pretty dangerous. As was his other
clip with him sitting on top of the wall with the circular saw held between
his knees and then on top of a ladder holding the wall with his left hand
behind and his arm under the saw while cutting. A kick back there would have
sent the blade right through his forearm...
John