I have a router that is on a fairly large, nice, aluminum router table.
That, in turn, is mounted on a frame made out of 2 x 4 and other materials.
The top of the thing is around 48" high, and is tippy. It does have
lockable wheels, but they are mounted in much too small of a rectangle,
IMHO. Is there a standard height to put a router table, or is it up to the
person, as heights vary.
I have a wash sink that I wash my dogs in. The height is such that I cannot
wash one of them without severe back cramping. Obviously, I want to make it
higher or lower than that.
But, is there a standard height, is it up to the user, is it good to have
more than one height so that different work can be done differently?
Thanks.
Steve
" But, is there a standard height, is it up to the user, is it good to
have
more than one height so that different work can be done differently?"
******************************************************************
Indeed the task and your anatomy determine the height of a stationary.
And the best height must be determined experimentally.
How? With the variable height of the drill press table.
Mimic the intended procedure on the press and adjust the table height
until comfortable.
Build your stand accordingly.
http://www.patwarner.com Routers
****************************************
In article <X%[email protected]>,
Steve B <[email protected]> wrote:
> I have a router that is on a fairly large, nice, aluminum router table.
> That, in turn, is mounted on a frame made out of 2 x 4 and other
> materials. The top of the thing is around 48" high, and is tippy. It
> does have lockable wheels, but they are mounted in much too small of a
> rectangle, IMHO. Is there a standard height to put a router table, or
> is it up to the person, as heights vary.
Height is going to be down to what you are comfortable with but 48" does
sound a bit high.
As far as being "tippy" that is down to getting the centre of gravity
lower.
My shop is small so I cannot afford any wasted space so I fill the
underneath of benches and tables with draws or cupboards.
My router table is based on one I purchased from B&Q some years ago. The
Aluminium top was fine but the support was ill conceived and badly
designed. Two plastic mouldings supported the top each side of the router
space and these sat on a sheet steel base with curved uprights at each
corner and two shelves. A panel stretched across the front below the edge
of the table and carried the switch and a socket outlet to feed the
router, restricting access to the router. The whole thing was very
wasteful of space so I built a new wooden base. It has adjustable feet at
each corner to level it up because the floor is uneven and slopes.
http://s298.photobucket.com/albums/mm256/stuartwinsor/Router%20table/
The lower draws contain my hand power tools, the bottom one has three
circular saws and several other items. It is quite full and heavy
requiring a bit of effort to pull it out. This low down weight ensures
stability.
The top LH small draw is fitted out for those router cutters which do not
have their own packets/cases. Normally when I buy cutters I keep them in
the manufacturers supplied packaging but some were bought in boxed sets.
The Aluminium top is 680x450mm and it is 880mm off the floor. There is
additional space behind the aluminium table, almost like the tool well on
a bench, making the overall front to back measurement 600mm
--
Stuart Winsor
Only plain text for emails
http://www.asciiribbon.org
Many things to consider, back, vision etc. I try to keep most work areas
between my belly button and my elbows. Just a thought
Joe M.
"Steve B" <[email protected]> wrote in message
news:X%[email protected]...
>I have a router that is on a fairly large, nice, aluminum router table.
>That, in turn, is mounted on a frame made out of 2 x 4 and other materials.
>The top of the thing is around 48" high, and is tippy. It does have
>lockable wheels, but they are mounted in much too small of a rectangle,
>IMHO. Is there a standard height to put a router table, or is it up to the
>person, as heights vary.
>
> I have a wash sink that I wash my dogs in. The height is such that I
> cannot wash one of them without severe back cramping. Obviously, I want
> to make it higher or lower than that.
>
> But, is there a standard height, is it up to the user, is it good to have
> more than one height so that different work can be done differently?
>
> Thanks.
>
> Steve
>
In article <46fdf730-bf26-4368-9965-5c1cfa3c7d48
@t15g2000yqi.googlegroups.com>, [email protected] says...
>
> " But, is there a standard height, is it up to the user, is it good to
> have
> more than one height so that different work can be done differently?"
> ******************************************************************
> Indeed the task and your anatomy determine the height of a stationary.
> And the best height must be determined experimentally.
> How? With the variable height of the drill press table.
> Mimic the intended procedure on the press and adjust the table height
> until comfortable.
> Build your stand accordingly.
> http://www.patwarner.com Routers
> ****************************************
Now that is one of those "why didn't I think of that" approaches.
On 2/23/2012 3:15 PM, Steve B wrote:
> I have a router that is on a fairly large, nice, aluminum router table.
> That, in turn, is mounted on a frame made out of 2 x 4 and other materials.
> The top of the thing is around 48" high, and is tippy. It does have
> lockable wheels, but they are mounted in much too small of a rectangle,
> IMHO. Is there a standard height to put a router table, or is it up to the
> person, as heights vary.
>
> I have a wash sink that I wash my dogs in. The height is such that I cannot
> wash one of them without severe back cramping. Obviously, I want to make it
> higher or lower than that.
>
> But, is there a standard height, is it up to the user, is it good to have
> more than one height so that different work can be done differently?
>
> Thanks.
>
> Steve
>
>
Typically router table height is the same as your, TS.
On Thu, 23 Feb 2012 13:15:36 -0800, "Steve B" <[email protected]>
wrote:
>I have a router that is on a fairly large, nice, aluminum router table.
>That, in turn, is mounted on a frame made out of 2 x 4 and other materials.
>The top of the thing is around 48" high, and is tippy. It does have
>lockable wheels, but they are mounted in much too small of a rectangle,
>IMHO. Is there a standard height to put a router table, or is it up to the
>person, as heights vary.
>
>I have a wash sink that I wash my dogs in. The height is such that I cannot
>wash one of them without severe back cramping. Obviously, I want to make it
>higher or lower than that.
>
>But, is there a standard height, is it up to the user, is it good to have
>more than one height so that different work can be done differently?
>
>Thanks.
>
>Steve
>
Most are about 32" or so, but since we all come in different heights,
what works best for you may not for me. Mine is the same as my table
saw so if I have a long piece to put through it, the table saw can act
as an extra support.
You want it low enough that you can keep a downward pressure on the
part while feeding it across the bit. Too high you lose leverage.