I am making a potting shed for my wife. As many of us know, these
things must be cute instead of utilitarian. For me that means custom
windows. They must be 6 or eight light in pairs. Window will be about
18-20" wide and about 36 or so tall. Anyone ever took on such a
project? This does not have to be a fancy window like a double hung.
More like a "wall of glass". A frame with the glass panes in it and to
open the window you can just tilt it inside 6 or 8 inches and hold it
with a chain. Any ideas how to do this? Making the "window" part of
the window that is.
I have all the regular shop cast of characters. Hand and power tools,
and a decent amount of ability to use them should I know how to start
at least. Any websites or book dedicated to homemade windows? I
checked my local Barnes and noble with no luck as well as my library.
Thanks for any help.
[email protected] wrote:
> I am making a potting shed for my wife. As many of us know, these
> things must be cute instead of utilitarian. For me that means custom
> windows. They must be 6 or eight light in pairs. Window will be about
> 18-20" wide and about 36 or so tall. Anyone ever took on such a
> project? This does not have to be a fancy window like a double hung.
> More like a "wall of glass". A frame with the glass panes in it and to
> open the window you can just tilt it inside 6 or 8 inches and hold it
> with a chain. Any ideas how to do this? Making the "window" part of
> the window that is.
<snip>
Cope and stick construction is used for an actual lighted window. For a
potting shed I'd make a simulated lighted window with just an overlay over
the full pane to obtain the desired look. The overlay could be as simple
as some half lapped slats.
--
Jack Novak
Buffalo, NY - USA
(Remove "SPAM" from email address to reply)
[email protected] wrote:
>
> I am making a potting shed for my wife. As many of us know, these
> things must be cute instead of utilitarian. For me that means custom
> windows. They must be 6 or eight light in pairs. Window will be about
> 18-20" wide and about 36 or so tall. Anyone ever took on such a
> project? This does not have to be a fancy window like a double hung.
> More like a "wall of glass". A frame with the glass panes in it and to
> open the window you can just tilt it inside 6 or 8 inches and hold it
> with a chain. Any ideas how to do this? Making the "window" part of
> the window that is.
...
There's an article in a recent FWW showing a simplified way of making
divided light transom windows...all required is to change the size to
whatever you want.
I've built a large number of replacement windows for the
barn...traditional cope and stick is simple w/ either the Whiteside or
other combination router bits if you don't want the through tenon. CMT
and Amana also make a set, I'm sure there are others as well.
Delta has quit making their line of 1/2" spindle shaper cutters
entirely, unfortunately, which is the only place I know of to get the
stub-shaft cutter required to make the relief cut in order to make the
full tenon. As I have another set of sixteen to go, I'm thinking I'll
get a custom one made to match the profile of the Whiteside router
set...
But, for just one or two and if you're looking for simple, look for the
FWW article--I'll see if I can find and post the particular issue...
Duane Bozarth wrote:
>
> Duane Bozarth wrote:
> ...
> > There's an article in a recent FWW showing a simplified way of making
> > divided light transom windows...all required is to change the size to
> > whatever you want.
>
> Sorry, that was FHB, not FWW...
And, it was #165, Sept '04...
His technique used separate tack-on moulding on both sides for an
interior window. For an exterior window I'd suggest standard glazing for
the outside instead.
> [email protected] wrote:
>>
>> A frame with the glass panes in it and to
>> open the window you can just tilt it inside 6 or 8 inches and hold it
>> with a chain.
You may want a plan "b" for opening the window. That much glass in the sun
can get awfully hot inside of a shed.
I made 2 simple replacement windows by making the frames out of scraps
butted together. Then I used 1/2" quarter-round moulding mitered inside
to hold the plexiglas.
Hope this helps.
Joe
[email protected] wrote:
> I am making a potting shed for my wife. As many of us know, these
> things must be cute instead of utilitarian. For me that means custom
> windows. They must be 6 or eight light in pairs. Window will be about
> 18-20" wide and about 36 or so tall. Anyone ever took on such a
> project? This does not have to be a fancy window like a double hung.
> More like a "wall of glass". A frame with the glass panes in it and to
> open the window you can just tilt it inside 6 or 8 inches and hold it
> with a chain. Any ideas how to do this? Making the "window" part of
> the window that is.
>
> I have all the regular shop cast of characters. Hand and power tools,
> and a decent amount of ability to use them should I know how to start
> at least. Any websites or book dedicated to homemade windows? I
> checked my local Barnes and noble with no luck as well as my library.
> Thanks for any help.
>