Starting a kitchen cabinet reface project (all cherry), doors will be tongue
and groove rail / stile with a 1/4" plywood panel. I didn't realize what a
problem it was going to be to find decent 1/4" plywood. Every local
supplier around here (San Diego) only carries imported MDF core junk. The
face veneer is so thin on that stuff I don't think it would ever hold up to
daily kitchen abuse. Plus it breaks really easily. I found one place in
San Diego (THH Hardwood) that said they could order 1/4" veneer core cherry
that was domestic, so I went for it. When I went to pickup the order the
plywood appeared to be MDF core, the face veneer was as thin as cheap toilet
paper - I refused it.
Has anyone had success using the mdf core stuff for cabinet doors? Any
suggestions for source for veneer core plywood in Southern California? I'm
willing to travel to get quality wood.
Thanks,
Carl
I too couldn't find decent 1/4" cherry ply in San Diego. Went up to
Cut and Dryed in Solona Beach and it was junk. I was also making
cabinet doors. Did not try TH&H or Frost because I didn't need a
whole sheet. Ended up using my PSA cherry ply veneer that is used on
the face frames on 1/4" birch ply and cutting the slots a tad bit wider
to fit the additional thickness. Works fine.
Carl wrote:
> Starting a kitchen cabinet reface project (all cherry), doors will be tongue
> and groove rail / stile with a 1/4" plywood panel. I didn't realize what a
> problem it was going to be to find decent 1/4" plywood. Every local
> supplier around here (San Diego) only carries imported MDF core junk. The
> face veneer is so thin on that stuff I don't think it would ever hold up to
> daily kitchen abuse. Plus it breaks really easily. I found one place in
> San Diego (THH Hardwood) that said they could order 1/4" veneer core cherry
> that was domestic, so I went for it. When I went to pickup the order the
> plywood appeared to be MDF core, the face veneer was as thin as cheap toilet
> paper - I refused it.
>
> Has anyone had success using the mdf core stuff for cabinet doors? Any
> suggestions for source for veneer core plywood in Southern California? I'm
> willing to travel to get quality wood.
>
> Thanks,
>
> Carl
I have scoured the San Diego suppliers, all with the same result. Do you
have any names and or contacts for suppliers in LA?
Thanks,
Carl
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> Carl wrote:
>
>
>> Any suggestions for source for veneer core plywood in Southern
>> California? I'm willing to travel to get quality wood.
>
>
> If you are willing to drive to L/A, there are several plywood distributors
> serving the cabinet makers.
>
> Should be at least a couple in San Diego.
>
> Forget the retailers.
>
> Lew
Carl wrote:
> Any
> suggestions for source for veneer core plywood in Southern California? I'm
> willing to travel to get quality wood.
If you are willing to drive to L/A, there are several plywood
distributors serving the cabinet makers.
Should be at least a couple in San Diego.
Forget the retailers.
Lew
I thought of applying veneer myself, it came out to >$100 per sheet. Did
you leave the Birch veneer on the inside of the door? Curious how it came
out, did you have to stain or dye the birch to match the cherry veneer?
Regards,
Carl
"Jerry" <[email protected]> wrote in message
news:[email protected]...
>I too couldn't find decent 1/4" cherry ply in San Diego. Went up to
> Cut and Dryed in Solona Beach and it was junk. I was also making
> cabinet doors. Did not try TH&H or Frost because I didn't need a
> whole sheet. Ended up using my PSA cherry ply veneer that is used on
> the face frames on 1/4" birch ply and cutting the slots a tad bit wider
> to fit the additional thickness. Works fine.
>
>
> Carl wrote:
>> Starting a kitchen cabinet reface project (all cherry), doors will be
>> tongue
>> and groove rail / stile with a 1/4" plywood panel. I didn't realize what
>> a
>> problem it was going to be to find decent 1/4" plywood. Every local
>> supplier around here (San Diego) only carries imported MDF core junk.
>> The
>> face veneer is so thin on that stuff I don't think it would ever hold up
>> to
>> daily kitchen abuse. Plus it breaks really easily. I found one place in
>> San Diego (THH Hardwood) that said they could order 1/4" veneer core
>> cherry
>> that was domestic, so I went for it. When I went to pickup the order the
>> plywood appeared to be MDF core, the face veneer was as thin as cheap
>> toilet
>> paper - I refused it.
>>
>> Has anyone had success using the mdf core stuff for cabinet doors? Any
>> suggestions for source for veneer core plywood in Southern California?
>> I'm
>> willing to travel to get quality wood.
>>
>> Thanks,
>>
>> Carl
>