> I know when hand planing one must go in the direction of the grain
> traveling up and away from the user of the plane... is there such a
> rule of any kind for either ripping or cross cutting on a table saw?
>
> Thanks all,
Not that I know of.
I'm only cautious of wood orientation to avoid cutting through knots were
possible or when trying to saw cupped boards etc.
If you are ripping, you are working with the grain. If you are corss
cutting, well you are cutting across the grain. You can get different blades
to perform each of those tasks better however, i.e. a rip blade for cutting
with the grain (has fewer teeth, 24 or so) and crosscut blade for cutting
across grain (has more teeth, 60 or so). You can get combination blades with
around 40 teeth that will both rip anjd crosscut to a reasonable finish if
you dont want to change blades frequently.
--
Regards,
Dean Bielanowski
Editor,
Online Tool Reviews
http://www.onlinetoolreviews.com
Over 70 woodworking product reviews online!
------------------------------------------------------------
Latest 6 Reviews:
- GMC BJ110 Biscuit Joiner
- Karcher NT361 Dust Extractor
- Ozito Electronic Ear Muffs
- Festool TDK Cordless Drills
- Infinity Kitchen Making Router Bit Set
- Jorgensen Cabinet Master Clamps
------------------------------------------------------------
"AAvK" <[email protected]> wrote in message
news:31xQd.96778$mt.82884@fed1read03...
>
> I know when hand planing one must go in the direction of the grain
> traveling up and away from the user of the plane... is there such a
> rule of any kind for either ripping or cross cutting on a table saw?
No rule that I know of however on some woods, Poplar for instance, I see a
difference when ripping one direction vs. another if my blade has not been
to the sharpener recently. From my experience the more dense and harder the
wood the less likely of a fuzz edge.
In article <[email protected]>,
"Woodcrafter" <[email protected]> wrote:
> > I know when hand planing one must go in the direction of the grain
> > traveling up and away from the user of the plane... is there such a
> > rule of any kind for either ripping or cross cutting on a table saw?
> >
> > Thanks all,
>
> Not that I know of.
> I'm only cautious of wood orientation to avoid cutting through knots were
> possible or when trying to saw cupped boards etc.
> If you are ripping, you are working with the grain. If you are corss
> cutting, well you are cutting across the grain. You can get different blades
> to perform each of those tasks better however, i.e. a rip blade for cutting
> with the grain (has fewer teeth, 24 or so) [snip]
A lot of people don't know what it is like to own a good ripping blade.
They would be surprised to discover how clean an edge those can leave
and how effortless they operate.
In my line of work (yea, yea, yea...countertops..*G*) I sometimes build
custom laminate tops with a wood edge. So long and skinny strips are
what I'm after. Cutting with the grain has a nice feel to it. No
sawdust. Just a bezillion small curls.
Mine is an Optima from Royce/Ayr. 10" 24 teeth... all rakers.
I think if Steve Knight were to design a sawblade, it would most likely
work like that.
A blade like that also makes a wonderful rabbet along the length of a
board, nice flat bottom.
0¿0
Rob
"Every time I close my eyes, I see spots."
.."Did you see a doctor?"
"Nope... just spots..."
In article <31xQd.96778$mt.82884@fed1read03>,
"AAvK" <[email protected]> wrote:
> I know when hand planing one must go in the direction of the grain
> traveling up and away from the user of the plane... is there such a
> rule of any kind for either ripping or cross cutting on a table saw?
>
> Thanks all,
If there is a rule, I have never observed it.
Jointers and planers, yes.... some router situations for sure, cuz there
is nothing like lifting a 6" sliver off an oak edge with a round-over
bit... or so I'm told. But in those situations I climb-cut if the bit
isn't too big.
I stand (or sit) to be corrected though....
This is one of those questions that makes me go mmmmmm.
0¿0
Rob
Would a drum sander give a shit about grain direction, he wonders out
loud?
"Every time I close my eyes, I see spots."
"Did you see a doctor?"
"No, just spots."
On Tue, 15 Feb 2005 17:07:13 -0800, "AAvK" <[email protected]> wrote:
>I know when hand planing one must go in the direction of the grain
>traveling up and away from the user of the plane... is there such a
>rule of any kind for either ripping or cross cutting on a table saw?
Not that I'm aware of.
I might rip one edge or the other if one side has a wild grain and I
know I need to join or route it. Otherwise I don't pay much attention
to grain direction when ripping.
Mike O.
In article <31xQd.96778$mt.82884@fed1read03>,
"AAvK" <[email protected]> wrote:
> I know when hand planing one must go in the direction of the grain
> traveling up and away from the user of the plane... is there such a
> rule of any kind for either ripping or cross cutting on a table saw?
I think it makes a difference. As a matter of fact I posted my opinion
on this a couple years ago when I "discovered" it through my own
testing. If the keeper piece is to the right of the blade, you will get
a smoother cut (on the keeper) if the grain is angling from the upper
right to lower left (12:30 to 6:30 or more clockwise). The off-cut will
have a noticeably rougher surface than the keeper. Test it for yourself.
--
Owen Lowe and his Fly-by-Night Copper Company
____
"Sure we'll have fascism in America, but it'll come disguised
as 100% Americanism." -- Huey P. Long