I'm not whining, I'm asking if anyone else has the same problem or if
there is an easy solution.
I got some square drive screws today. I noticed they stick to the
screw driver and thought that was cool since it would be like a
magnetic tip screwdriver with a much stronger grip. Then I drove some
into a 2 x 4 and had trouble removing the drill from the screw head.
Well, I guess the obvious solution is to file the screw head. Any
other suggestions/clues/hints would be appreciated.
I don't don't do much fastening, so it's no big deal in any case.
Thank you.
On Jul 14, 1:54 am, John Doe <[email protected]> wrote:
> I'm not whining, I'm asking if anyone else has the same problem or if
> there is an easy solution.
>
> I got some square drive screws today. I noticed they stick to the
> screw driver and thought that was cool since it would be like a
> magnetic tip screwdriver with a much stronger grip. Then I drove some
> into a 2 x 4 and had trouble removing the drill from the screw head.
>
> Well, I guess the obvious solution is to file the screw head. Any
> other suggestions/clues/hints would be appreciated.
>
> I don't don't do much fastening, so it's no big deal in any case.
> Thank you.
Ahhh, the stickiness of a fresh bit. Give it a few screws and it will
loosen up soon enough.
Then you'll be looking for a fresh bit that's sticky again.
r
I always roll off when I'm done screwing.
On Jul 13, 11:11 pm, "Mike Dobony" <[email protected]> wrote:
> "John Doe" <[email protected]> wrote in message
>
> news:[email protected]...
>
>
>
>
>
>
>
> > I'm not whining, I'm asking if anyone else has the same problem or if
> > there is an easy solution.
>
> > I got some square drive screws today. I noticed they stick to the
> > screw driver and thought that was cool since it would be like a
> > magnetic tip screwdriver with a much stronger grip. Then I drove some
> > into a 2 x 4 and had trouble removing the drill from the screw head.
>
> > Well, I guess the obvious solution is to file the screw head. Any
> > other suggestions/clues/hints would be appreciated.
>
> > I don't don't do much fastening, so it's no big deal in any case.
> > Thank you.
>
> Roll the tip off the screw instead of just pulling it off straight.- Hide quoted text -
>
> - Show quoted text -
On Sat, 14 Jul 2007 06:11:45 GMT, "Mike Dobony"
<[email protected]> wrote:
>
>Roll the tip off the screw instead of just pulling it off straight.
What he said, with the addition that the motion quickly becomes second
nature. You won't even think about it after a few more screws!
---------------------------------------------
** http://www.bburke.com/woodworking.html **
---------------------------------------------
"John Doe" <[email protected]> wrote in message
news:[email protected]...
>
> I'm not whining, I'm asking if anyone else has the same problem or if
> there is an easy solution.
>
> I got some square drive screws today. I noticed they stick to the
> screw driver and thought that was cool since it would be like a
> magnetic tip screwdriver with a much stronger grip. Then I drove some
> into a 2 x 4 and had trouble removing the drill from the screw head.
>
> Well, I guess the obvious solution is to file the screw head. Any
> other suggestions/clues/hints would be appreciated.
>
> I don't don't do much fastening, so it's no big deal in any case.
> Thank you.
I find they stick on occassion, particularly if driving into harder
materials requiring a little torque. My guess is the driver tip slightly
cuts into the screw head making it stick a little. I usually just wiggle the
drill a little and it pops off whenever it happens.
--
Regards,
Dean Bielanowski
Editor
OnlineToolReviews.com
http://www.onlinetoolreviews.com
Over 150+ free tool reviews online!
"Edwin Pawlowski" <[email protected]> wrote in message
news:[email protected]...
>
> "B A R R Y" <[email protected]> wrote in message
>>
>>
>> What he said, with the addition that the motion quickly becomes second
>> nature. You won't even think about it after a few more screws!
>>
>
> How many times do you figure for the minimum number of screws before you get the motion down right?
> Personally, I don't recall ever having a screw where the motion was not acceptable.
Like the boy who fell in the sewer and couldn't swim, how long before he'll just be going through the
motions....
You're wife must be feeling old age creep on... ;-)
"SonomaProducts.com" <[email protected]> wrote in message
news:[email protected]...
>I always roll off when I'm done screwing.
>
>
> On Jul 13, 11:11 pm, "Mike Dobony" <[email protected]> wrote:
>> "John Doe" <[email protected]> wrote in message
>>
>> news:[email protected]...
>>
>>
>>
>>
>>
>>
>>
>> > I'm not whining, I'm asking if anyone else has the same problem or if
>> > there is an easy solution.
>>
>> > I got some square drive screws today. I noticed they stick to the
>> > screw driver and thought that was cool since it would be like a
>> > magnetic tip screwdriver with a much stronger grip. Then I drove some
>> > into a 2 x 4 and had trouble removing the drill from the screw head.
>>
>> > Well, I guess the obvious solution is to file the screw head. Any
>> > other suggestions/clues/hints would be appreciated.
>>
>> > I don't don't do much fastening, so it's no big deal in any case.
>> > Thank you.
>>
>> Roll the tip off the screw instead of just pulling it off straight.- Hide quoted text -
>>
>> - Show quoted text -
>
>
"John Doe" <[email protected]> wrote in message
news:[email protected]...
>
> I'm not whining, I'm asking if anyone else has the same problem or if
> there is an easy solution.
>
> I got some square drive screws today. I noticed they stick to the
> screw driver and thought that was cool since it would be like a
> magnetic tip screwdriver with a much stronger grip. Then I drove some
> into a 2 x 4 and had trouble removing the drill from the screw head.
>
> Well, I guess the obvious solution is to file the screw head. Any
> other suggestions/clues/hints would be appreciated.
>
> I don't don't do much fastening, so it's no big deal in any case.
> Thank you.
>
>
Roll the tip off the screw instead of just pulling it off straight.
"B A R R Y" <[email protected]> wrote in message
>
>
> What he said, with the addition that the motion quickly becomes second
> nature. You won't even think about it after a few more screws!
>
How many times do you figure for the minimum number of screws before you get
the motion down right? Personally, I don't recall ever having a screw where
the motion was not acceptable.
"John Doe" <[email protected]> wrote in message
news:[email protected]...
>
> I'm not whining, I'm asking if anyone else has the same problem or if
> there is an easy solution.
>
> I got some square drive screws today. I noticed they stick to the
> screw driver and thought that was cool since it would be like a
> magnetic tip screwdriver with a much stronger grip. Then I drove some
> into a 2 x 4 and had trouble removing the drill from the screw head.
>
> Well, I guess the obvious solution is to file the screw head. Any
> other suggestions/clues/hints would be appreciated.
>
> I don't don't do much fastening, so it's no big deal in any case.
> Thank you.
>
>
Just wiggle the drill back and forth and the bit will come out of the screw.
Better to have the screw stick than to fall off. This is great for starting
screws in hard to reach places.
On Sat, 14 Jul 2007 13:30:10 GMT, "Edwin Pawlowski" <[email protected]>
wrote:
>
>"B A R R Y" <[email protected]> wrote in message
>>
>>
>> What he said, with the addition that the motion quickly becomes second
>> nature. You won't even think about it after a few more screws!
>>
>
>How many times do you figure for the minimum number of screws before you get
>the motion down right?
2. <G>
---------------------------------------------
** http://www.bburke.com/woodworking.html **
---------------------------------------------
On Sat, 14 Jul 2007 11:00:42 GMT, B A R R Y <[email protected]> wrote:
>On Sat, 14 Jul 2007 06:11:45 GMT, "Mike Dobony"
><[email protected]> wrote:
>
>>
>>Roll the tip off the screw instead of just pulling it off straight.
>
>
>What he said, with the addition that the motion quickly becomes second
>nature. You won't even think about it after a few more screws!
>
That's what my wife keeps saying...
and I think she's right...
mac
Please remove splinters before emailing