Nuke wrote:
> Just built a pine blanket chest and for the top joined three boards
> together. The Pine was kiln dried and now it is warping, the top is
> approximately 4' x 3' , any ideas how I can undo the warping?
Have you recently started using air conditioning, opening windows,
or have you put damp items in the chest?
I'm guessing that this is a flat lid and the warping is a large scale
cupping of the top. I'm also guessing that the lid is only finished
on the outside.
If so, then the warping is likely to have been caused by a change
in ambient humidity that has caused moisture to enter or leave
the wood faster through the unfinished side. If so, it will correct
itself if it is expsoed to a prolonged period of stable humidity.
Or, if the unfinihsed side of the lid is concave you you can carefully
moisten it by wiping once day or so with a damp rag. If it is
convex, you can carefully dry it as with a hair drier. You have
to go slowly to avoid splitting the wood. You can also take the
top off and lay it convex side up in the sun or on cement.
The idea here is that the moister face of the llid has expanded
more than the other making that side convex, so that you need
to dry it, or moisten the concave side to even it out, or both.
When the lid is flat again, finish the inside just like the outside is
finished and it should remain fairly stable. Wood finishes do
not stop moisture from diffusing into or out of wood, they slow
the rate of diffusion through the surface. That way the higher
diffusion rate thorugh the bulk of the wood prevents the formation
of a moisure gradient which is what causes major warping.
It also helps, when edge gluing boards to make a wide panel,
to alternate the orientation of the cupping of the grain so that
as one board cups up the adjacent ones cup down. That is,
arrange the boards so that what was the bark side of the tree
is down on one board and up on the adjacent boards. Like this:
unu
That makes for a panel with better overall stablity but
limits your options regarding matching for appearance and
control of tearout should you wish to plane the panel
after gluing.
--
FF
Nuke wrote:
> Just built a pine blanket chest and for the top joined three boards
> together. The Pine was kiln dried and now it is warping, the top is
> approximately 4' x 3' , any ideas how I can undo the warping?
Have you recently started using air conditioning, opening windows,
or have you put damp items in the chest?
I'm guessing that this is a flat lid and the warping is a large scale
cupping of the top. I'm also guessing that the lid is only finished
on the outside.
If so, then the warping is likely to have been caused by a change
in ambient humidity that has caused moisture to enter or leave
the wood faster through the unfinished side. If so, it will correct
itself if it is expsoed to a prolonged period of stable humidity.
Or, if the unfinihsed side of the lid is concave you you can carefully
moisten it by wiping once day or so with a damp rag. If it is
convex, you can carefully dry it as with a hair drier. You have
to go slowly to avoid splitting the wood. You can also take the
top off and lay it convex side up in the sun or on cement.
The idea here is that the moister face of the llid has expanded
more than the other making that side convex, so that you need
to dry it, or moisten the concave side to even it out, or both.
When the lid is flat again, finish the inside just like the outside is
finished and it should remain fairly stable. Wood finishes do
not stop moisture from diffusing into or out of wood, they slow
the rate of diffusion through the surface. That way the higher
diffusion rate thorugh the bulk of the wood prevents the formation
of a moisure gradient which is what causes major warping.
It also helps, when edge gluing boards to make a wide panel,
to alternate the orientation of the cupping of the grain so that
as one board cups up the adjacent ones cup down. That is,
arrange the boards so that what was the bark side of the tree
is down on one board and up on the adjacent boards. Like this:
unu
That makes for a panel with better overall stablity but
limits your options regarding matching for appearance and
control of tearout should you wish to plane the panel
after gluing.
--
FF
"Nuke" <[email protected]> wrote in message
news:[email protected]...
> Just built a pine blanket chest and for the top joined three boards
> together. The Pine was kiln dried and now it is warping, the top is
> approximately 4' x 3' , any ideas how I can undo the warping?
>
Are both side finished?
Add hardwood cleats under the lid. - Elongated screw holes, glue only the
center board.
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com
To stop that on my cabinet doors I put two pieces that go length wise then
two that go across. the two that are going across are only 1 1/2 in thick
but it has kept them from warping for 8 years. I live in the Portland
Oregon area and it is wet here. :) Don;t know if that helps but try to put
some wood under the top going across the grain to suck it down.
Al
"Nuke" <[email protected]> wrote in message
news:[email protected]...
> Just built a pine blanket chest and for the top joined three boards
> together. The Pine was kiln dried and now it is warping, the top is
> approximately 4' x 3' , any ideas how I can undo the warping?
>
"Nuke" <[email protected]> wrote in message
news:[email protected]...
> Just built a pine blanket chest and for the top joined three boards
> together. The Pine was kiln dried and now it is warping, the top is
> approximately 4' x 3' , any ideas how I can undo the warping?
If this is "new" pine you'd be hard pressed to keep a single one of those 3
foot-wide boards flat let alone all three flat as a unit. I'd be inclined to
rip the top into at least six pieces, nine wouldn't be too many, and glue it
back together. The ripping would relieve some of the stresses in the wood
and may help keep the top flat. Additionally, cleats on the bottom side of
the top would help--screwed through elongated holes or attached via a
sliding dovetail across the width, unglued, would be two approaches.
John