Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch width.
Now I'm thinking that maybe a 5/8" would be great when cutting would produce
results with less drift, and straighter cuts. If this is the case which
blades do you recommend in brand, number of teeth, and type of teeth? Also,
what about going to 3/4"?
regards
"Woodchuck" <[email protected]> wrote in message
news:[email protected]...
> Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch
> width. Now I'm thinking that maybe a 5/8" would be great when cutting
> would produce results with less drift, and straighter cuts. If this is the
> case which blades do you recommend in brand, number of teeth, and type of
> teeth? Also, what about going to 3/4"?
>
> regards
Many bandsaw specs say then can take a 3/4" blade. Truth is, it will fit
the wheels, but it will not cut any better, maybe even worse.
Instead of a wider blade, look for Duginski's bandsaw book and read it. You
will learn how to set it up properly, how to adjust it so the blade tracks
better, and you will find that a 1/4" blade will do most of the general
cutting you'll ever do. Save the 1/2" for resawing and use the 1/8" for
more intricate work. Better yet, buy two more saws and save that pesky
blade changing.
--
Ed
http://pages.cthome.net/edhome/
On Sun, 19 Dec 2004 20:53:16 -0500, "Woodchuck"
<[email protected]> wrote:
>Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch width.
>Now I'm thinking that maybe a 5/8" would be great
No, probably worse.
Try reading Duginske - lots of good stuff on blade choice in there.
It also helps to find a clueful blade supplier - most aren't, and
don't even know what tooth pattern they're selling you.
For a typical 14" machine, 5/8" is tops, 3/4" is clearly too much and
1/2" is about as wide as it's sensible to go. There's a minimal
theoretical benefit to the wider blade, but only if your machine can
tension it - which it probably can't.
--
Smert' spamionam
Call Suffolk Machinery,
http://www.suffolkmachinery.com/
and ask them your questions. They are the supplier of Timberwolf blades and
know much more about your saw then any of us. And they are very helpful.
No affiliation, just a very satisfied repeat customer.
Michael Latcha - at home in Redford, MI
"Woodchuck" <[email protected]> wrote in message
news:[email protected]...
> Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch
> width. Now I'm thinking that maybe a 5/8" would be great when cutting
> would produce results with less drift, and straighter cuts. If this is the
> case which blades do you recommend in brand, number of teeth, and type of
> teeth? Also, what about going to 3/4"?
>
> regards
>
>
On Mon, 20 Dec 2004 02:20:25 +0000, Andy Dingley <[email protected]> wrote:
Strongly recommended. He could try the local library on Duginske's books and
videos. Last week I borrowed a dozen videos and books on various woodworking
topics. I prefer video and see exactly how it was done and replay as many times
as necessary.
>On Sun, 19 Dec 2004 20:53:16 -0500, "Woodchuck"
><[email protected]> wrote:
>
>>Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch width.
>
>>Now I'm thinking that maybe a 5/8" would be great
>
>No, probably worse.
>
>
>Try reading Duginske - lots of good stuff on blade choice in there.
>It also helps to find a clueful blade supplier - most aren't, and
>don't even know what tooth pattern they're selling you.
>
>For a typical 14" machine, 5/8" is tops, 3/4" is clearly too much and
>1/2" is about as wide as it's sensible to go. There's a minimal
>theoretical benefit to the wider blade, but only if your machine can
>tension it - which it probably can't.
FWIW, I am using an Olson 5/8, 3 TPI. .025, hook tooth blade in my 60 year
old 14" delta BS.
Blade runs true with no wobble, and I cut 1/8 inch veneer from
hardwoods with great results.
However, I make no claims that a narrower, sharp, coarse blade
will not also do a great job. Jim
Woodchuck <[email protected]> wrote in message
news:[email protected]...
> Got a 14inch Rigid BS and have a few blades already in 1/4 & 1/2 inch
width.
> Now I'm thinking that maybe a 5/8" would be great when cutting would
produce
> results with less drift, and straighter cuts. If this is the case which
> blades do you recommend in brand, number of teeth, and type of teeth?
Also,
> what about going to 3/4"?
>
> regards
>
>
>