All:
Sounds silly, I realize, but I'm having a bit of a problem replacing a
damanged power cord on my Delta Contractor's Saw. (Discovered quite by
accident that the cord had been resting on the drive belt (!!!), and
the black insulating jacket had been reduced to a pile of powder
leaving about 2" of fully exposed wire. For a small slit, I'd consider
just wrapping electrical tape around it, but I thought this damage was
too severe for that).
The problem arises with removal of the cord at the front switch. The
cord attaches to the switch at three terminals, two of which are
simple push-terminals and were pulled off easily with a pair of pliers.
The third terminal, however, is an o-ring secured to a rectangular
metal bracket via a small screw. That screw, despite much gnashing of
teeth and attempts by several people, will NOT budge.
Could someone advise if that screw post is secured by some type of
fixative or compound that purposely prevents removal? Or am I just the
unfortunate recpient of a cross-threaded screw? Or does Delta intend
for me to replace the whole thing - switch and cord - if the cord
becomes damaged? I suppose I could just cut the cord at the screw
terminal post and splice a new cord in its place, but that seems like a
sloppy repair..
Thanks for your help.
-David
<[email protected]> wrote in message
news:[email protected]...
> All:
>
> Sounds silly, I realize, but I'm having a bit of a problem replacing a
> damanged power cord on my Delta Contractor's Saw. (Discovered quite by
> accident that the cord had been resting on the drive belt (!!!), and
> the black insulating jacket had been reduced to a pile of powder
> leaving about 2" of fully exposed wire. For a small slit, I'd consider
> just wrapping electrical tape around it, but I thought this damage was
> too severe for that).
>
> The problem arises with removal of the cord at the front switch. The
> cord attaches to the switch at three terminals, two of which are
> simple push-terminals and were pulled off easily with a pair of pliers.
> The third terminal, however, is an o-ring secured to a rectangular
> metal bracket via a small screw. That screw, despite much gnashing of
> teeth and attempts by several people, will NOT budge.
>
> Could someone advise if that screw post is secured by some type of
> fixative or compound that purposely prevents removal? Or am I just the
> unfortunate recpient of a cross-threaded screw? Or does Delta intend
> for me to replace the whole thing - switch and cord - if the cord
> becomes damaged? I suppose I could just cut the cord at the screw
> terminal post and splice a new cord in its place, but that seems like a
> sloppy repair..
Grounding terminal, and probably a star washer? Crank hard. Especially in
a bi or tri-metallic situation you may have some major corrosion in the
area.
Get the new switch, discover what it wants and get the appropriate
connector. That way, even if you have to take out your dremel cutoff wheel
and saw the screw off, you'll be ready to rewire. Shortening by an inch or
two won't hurt, surely.
"Dave" <[email protected]> wrote in message
news:MvDye.15730$Hw5.7911@trndny09...
> that happened to me too. I cut out the damage and used wire nuts to wire
> it back together, along with some electrical tape. works fine. seems to
> me that delta needs to relocate their power cords.
They included tie wraps in my old beast. As well as directions. Maybe I
should look to see if any have snapped.
(3)Butt connectors, #33 Scotch Electrical Tape & a (1) piece of heavy duty
heat shrink . . . .
It will look professional and be very safe / sturdy.
Need details, post a request . . .
Steve
<[email protected]> wrote in message
news:[email protected]...
> All:
>
> Sounds silly, I realize, but I'm having a bit of a problem replacing a
> damanged power cord on my Delta Contractor's Saw. (Discovered quite by
> accident that the cord had been resting on the drive belt (!!!), and
> the black insulating jacket had been reduced to a pile of powder
> leaving about 2" of fully exposed wire. For a small slit, I'd consider
> just wrapping electrical tape around it, but I thought this damage was
> too severe for that).
>
> The problem arises with removal of the cord at the front switch. The
> cord attaches to the switch at three terminals, two of which are
> simple push-terminals and were pulled off easily with a pair of pliers.
> The third terminal, however, is an o-ring secured to a rectangular
> metal bracket via a small screw. That screw, despite much gnashing of
> teeth and attempts by several people, will NOT budge.
>
> Could someone advise if that screw post is secured by some type of
> fixative or compound that purposely prevents removal? Or am I just the
> unfortunate recpient of a cross-threaded screw? Or does Delta intend
> for me to replace the whole thing - switch and cord - if the cord
> becomes damaged? I suppose I could just cut the cord at the screw
> terminal post and splice a new cord in its place, but that seems like a
> sloppy repair..
>
> Thanks for your help.
>
> -David
>
What I have done is shortened & replaced with twist-lok female. Then made up
a real nice heavy SO12/3 Cord that can be removed when the saw is not in
use. Sort of like the new Bosch Tools have.
Steve
[email protected]> wrote in message
news:[email protected]...
> All:
>
> Sounds silly, I realize, but I'm having a bit of a problem replacing a
> damanged power cord on my Delta Contractor's Saw. (Discovered quite by
> accident that the cord had been resting on the drive belt (!!!), and
> the black insulating jacket had been reduced to a pile of powder
> leaving about 2" of fully exposed wire. For a small slit, I'd consider
> just wrapping electrical tape around it, but I thought this damage was
> too severe for that).
>
> The problem arises with removal of the cord at the front switch. The
> cord attaches to the switch at three terminals, two of which are
> simple push-terminals and were pulled off easily with a pair of pliers.
> The third terminal, however, is an o-ring secured to a rectangular
> metal bracket via a small screw. That screw, despite much gnashing of
> teeth and attempts by several people, will NOT budge.
>
> Could someone advise if that screw post is secured by some type of
> fixative or compound that purposely prevents removal? Or am I just the
> unfortunate recpient of a cross-threaded screw? Or does Delta intend
> for me to replace the whole thing - switch and cord - if the cord
> becomes damaged? I suppose I could just cut the cord at the screw
> terminal post and splice a new cord in its place, but that seems like a
> sloppy repair..
>
> Thanks for your help.
>
> -David
>
[email protected] wrote:
> All:
>
> Sounds silly, I realize, but I'm having a bit of a problem replacing a
> damanged power cord on my Delta Contractor's Saw. (Discovered quite by
> accident that the cord had been resting on the drive belt (!!!), and
> the black insulating jacket had been reduced to a pile of powder
> leaving about 2" of fully exposed wire. For a small slit, I'd consider
> just wrapping electrical tape around it, but I thought this damage was
> too severe for that).
>
> The problem arises with removal of the cord at the front switch. The
> cord attaches to the switch at three terminals, two of which are
> simple push-terminals and were pulled off easily with a pair of pliers.
> The third terminal, however, is an o-ring secured to a rectangular
> metal bracket via a small screw. That screw, despite much gnashing of
> teeth and attempts by several people, will NOT budge.
>
> Could someone advise if that screw post is secured by some type of
> fixative or compound that purposely prevents removal? Or am I just the
> unfortunate recpient of a cross-threaded screw? Or does Delta intend
> for me to replace the whole thing - switch and cord - if the cord
> becomes damaged? I suppose I could just cut the cord at the screw
> terminal post and splice a new cord in its place, but that seems like a
> sloppy repair..
>
> Thanks for your help.
>
> -David
>
that happened to me too. I cut out the damage and used wire nuts to wire
it back together, along with some electrical tape. works fine. seems to
me that delta needs to relocate their power cords.
Cut that stubborn wire off about 2inches from the terminal, then
attach a quick connect of some kind and avoid maybe messing something
up at the terminal
John
On 5 Jul 2005 08:13:12 -0700, [email protected] wrote:
>All:
>
>Sounds silly, I realize, but I'm having a bit of a problem replacing a
>damanged power cord on my Delta Contractor's Saw. (Discovered quite by
>accident that the cord had been resting on the drive belt (!!!), and
>the black insulating jacket had been reduced to a pile of powder
>leaving about 2" of fully exposed wire. For a small slit, I'd consider
>just wrapping electrical tape around it, but I thought this damage was
>too severe for that).
>
>The problem arises with removal of the cord at the front switch. The
>cord attaches to the switch at three terminals, two of which are
>simple push-terminals and were pulled off easily with a pair of pliers.
>The third terminal, however, is an o-ring secured to a rectangular
>metal bracket via a small screw. That screw, despite much gnashing of
>teeth and attempts by several people, will NOT budge.
>
>Could someone advise if that screw post is secured by some type of
>fixative or compound that purposely prevents removal? Or am I just the
>unfortunate recpient of a cross-threaded screw? Or does Delta intend
>for me to replace the whole thing - switch and cord - if the cord
>becomes damaged? I suppose I could just cut the cord at the screw
>terminal post and splice a new cord in its place, but that seems like a
>sloppy repair..
>
>Thanks for your help.
>
>-David