I'm finally getting around to pulling my 12" Record vise out of storage and
installing it on a workbench. I have a question about suitable jaw liners
for the thing. Any suggestions on the best wood for this? Maple, something a
little softer? I'd even consider using magnetic jaws with rubber liners
except that the biggest I've seen are 6" wide, way too small for this 12"
vise.
Thanks for any suggestions.
"Upscale" wrote:
> I'm finally getting around to pulling my 12" Record vise out of
> storage and installing it on a workbench. I have a question about
> suitable jaw liners for the thing. Any suggestions on the best wood
> for this? Maple, something a little softer?
-------------------------------
Got some 1/2" (9 ply) Birch ply?
I'd use 2 layers (1" total thickness) per face.
Strong, stable and flat.
Lew
"J. Clarke" <[email protected]> wrote in message
> Just a thought but you can get 8-1/2 x 11 magnetic inkjet sheets at
> Staples, intended to make refrigerator magnets, at 15 bucks for a package
> of four. They're a little resilient with a paper facing--you should be
> able to glue a piece of rubber or whatever to them, they may even be OK as
> is--they're a little bit resilient but not very thic
I was thinking of adapting a pair of magnetic tool bars. The next time I'm
in Lee Valley, I'll check them out.
http://www.leevalley.com/en/wood/page.aspx?p=32153&cat=1,42363,42356
Like on my 8" wide monster metal vice - one jaw is Al, the other hard steel.
I talked to Dad about that - remember him making the Al on the lathe (no mill)
and now I can mill steel - he mentioned a soft jaw can save something under
compression. Hard materials will imprint while soft stuff will get marred.
So for softer stuff - use soft stuff and harder stuff - harder.
I have rubber inserts and Al inserts in my Gun vice. I use rubber mostly.
Martin
Martin H. Eastburn
@ home at Lions' Lair with our computer lionslair at consolidated dot net
"Our Republic and the Press will Rise or Fall Together": Joseph Pulitzer
TSRA: Endowed; NRA LOH & Patron Member, Golden Eagle, Patriot's Medal.
NRA Second Amendment Task Force Originator & Charter Founder
IHMSA and NRA Metallic Silhouette maker & member. http://lufkinced.com/
On 9/16/2010 8:13 PM, Upscale wrote:
> I'm finally getting around to pulling my 12" Record vise out of storage and
> installing it on a workbench. I have a question about suitable jaw liners
> for the thing. Any suggestions on the best wood for this? Maple, something a
> little softer? I'd even consider using magnetic jaws with rubber liners
> except that the biggest I've seen are 6" wide, way too small for this 12"
> vise.
>
> Thanks for any suggestions.
>
>
On 9/16/2010 9:37 PM, tiredofspam wrote:
> I would go with a smaller vise. You can send the 12" record to me.
>
> 8>)
>
> Maple is fine... Beech. You can line the moveable maple face with a
> piece of leather.
>
>
> On 9/16/2010 9:13 PM, Upscale wrote:
>> I'm finally getting around to pulling my 12" Record vise out of
>> storage and
>> installing it on a workbench. I have a question about suitable jaw liners
>> for the thing. Any suggestions on the best wood for this? Maple,
>> something a
>> little softer? I'd even consider using magnetic jaws with rubber liners
>> except that the biggest I've seen are 6" wide, way too small for this 12"
>> vise.
>>
>> Thanks for any suggestions.
>>
>>
Just a thought but you can get 8-1/2 x 11 magnetic inkjet sheets at
Staples, intended to make refrigerator magnets, at 15 bucks for a
package of four. They're a little resilient with a paper facing--you
should be able to glue a piece of rubber or whatever to them, they may
even be OK as is--they're a little bit resilient but not very thick.
"Upscale" <[email protected]> wrote in message
news:[email protected]...
> I'm finally getting around to pulling my 12" Record vise out of storage
> and installing it on a workbench. I have a question about suitable jaw
> liners for the thing. Any suggestions on the best wood for this? Maple,
> something a little softer? I'd even consider using magnetic jaws with
> rubber liners except that the biggest I've seen are 6" wide, way too small
> for this 12" vise.
>
> Thanks for any suggestions.
I guess it depends on what you are going to use it for. I used to have a
simple square 6" bench vise that I used for everything (before I broke it).
I used to cut a dozen or so jaws out of plywood at a time and leave them
stacked on the shelf above the bench. Whenever I needed to put something in
the vise I didn't want marred by the steels jaws I would drop a pair of
these in. They were great for things like aluminum motorcycle forks, etc.
I would cut them to be an exact match for the jaws at one end and loosely
fit over the center extension of the vise at the other. Worked great for
me. I would just throw them away as they got tore up, and I could get
amazing holding force out of them by crushing them around a work piece if
needed.
Now I have an aluminum vise, and I have prismatic plastic jaws for odd
shaped pieces at the other end of the work bench from my new(er) steel vise.
______
|_____|
| | | |
| | | |
On Thu, 16 Sep 2010 21:37:01 -0400, tiredofspam wrote:
> Maple is fine... Beech. You can line the moveable maple face with a
> piece of leather.
I've used some of the nonskid stuff they sell for shelf liners with good
results - the solid stuff, not the fancy open grid type.
--
Intelligence is an experiment that failed - G. B. Shaw
I would go with a smaller vise. You can send the 12" record to me.
8>)
Maple is fine... Beech. You can line the moveable maple face with a
piece of leather.
On 9/16/2010 9:13 PM, Upscale wrote:
> I'm finally getting around to pulling my 12" Record vise out of storage and
> installing it on a workbench. I have a question about suitable jaw liners
> for the thing. Any suggestions on the best wood for this? Maple, something a
> little softer? I'd even consider using magnetic jaws with rubber liners
> except that the biggest I've seen are 6" wide, way too small for this 12"
> vise.
>
> Thanks for any suggestions.
>
>
J. Clarke wrote the following:
> On 9/16/2010 9:37 PM, tiredofspam wrote:
>> I would go with a smaller vise. You can send the 12" record to me.
>>
>> 8>)
>>
>> Maple is fine... Beech. You can line the moveable maple face with a
>> piece of leather.
>>
>>
>> On 9/16/2010 9:13 PM, Upscale wrote:
>>> I'm finally getting around to pulling my 12" Record vise out of
>>> storage and
>>> installing it on a workbench. I have a question about suitable jaw
>>> liners
>>> for the thing. Any suggestions on the best wood for this? Maple,
>>> something a
>>> little softer? I'd even consider using magnetic jaws with rubber liners
>>> except that the biggest I've seen are 6" wide, way too small for
>>> this 12"
>>> vise.
>>>
>>> Thanks for any suggestions.
>>>
>>>
>
> Just a thought but you can get 8-1/2 x 11 magnetic inkjet sheets at
> Staples, intended to make refrigerator magnets, at 15 bucks for a
> package of four.
$14.00 for a pack of 5.
http://www.staples.com/Avery-Personal-Creations-Inkjet-Magnet-Sheets/product_46771
> They're a little resilient with a paper facing--you should be able to
> glue a piece of rubber or whatever to them, they may even be OK as
> is--they're a little bit resilient but not very thick.
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @