Anybody have any experience with these? I've got a couple projects coming
up where these are probably the right tool for the job... NOT fine
furniture! LOL Biscuits would be way too slow and pocket screws would only
save me glue drying time over the biscuits. Mortise and tenon or lap joints
would be overkill... most of it's pretty rough work.
The Senco is pricy and way more than I need... the Rockler fasteners are too
narrow for my purposes--only a 1/2" rather than the more typical 1" or so. I
see tools by SpotNails and Air Locker are available. The Bostitch is
interesting... a brand I've got experience with... coil nailer for framing.
I didn't find Porter Cable, Harbor Freight, or others tools.
Recommendations? Thoughts?
Thanks,
John
"Artemus" <[email protected]> wrote in message
news:[email protected]...
>
> "John Grossbohlin" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "JayPique" <[email protected]> wrote in message
>> news:[email protected]...
>>
>> You've pretty much nailed what I need it for... hold pine frames
>> together that will be laminated with hardboard or 3/8" ply, i.e, torsion
>> boxes.
> I've used 1/2" staples for holding the interior pieces when building
> torsion boxes
> and they've worked satisfactorily for me. YMMV.
I do the same thing for the interior pieces... that works out just fine for
me too.
John
"John Grossbohlin" <[email protected]> wrote in message
news:[email protected]...
> Anybody have any experience with these? I've got a couple projects coming
> up where these are probably the right tool for the job... NOT fine
> furniture! LOL Biscuits would be way too slow and pocket screws would
> only save me glue drying time over the biscuits. Mortise and tenon or lap
> joints would be overkill... most of it's pretty rough work.
>
> The Senco is pricy and way more than I need... the Rockler fasteners are
> too narrow for my purposes--only a 1/2" rather than the more typical 1" or
> so. I see tools by SpotNails and Air Locker are available. The Bostitch is
> interesting... a brand I've got experience with... coil nailer for
> framing. I didn't find Porter Cable, Harbor Freight, or others tools.
>
> Recommendations? Thoughts?
>
It has been awhile, but I got some that were applied with a hammer. They
also had some kind of driver for them that was much neater. But this ain't
art.
You pound them in and it holds the joint together. I saw them a month or so
ago. I can't remember where I got them. If you just need them for a simple
job, no need to buy a special tool. I assume you have a hammer.
"John Grossbohlin" wrote:
> Anybody have any experience with these?
----------------------------------------
A little.
----------------------------------------
> I've got a couple projects coming up where these are probably the
> right tool for the job...
----------------------------------------
I doubt that.
----------------------------------------
> NOT fine furniture! LOL
----------------------------------------
Or much of anything else IMHO.
Don't expect them to carry much of a load.
I'd go back to the thinking chair and start over.
----------------------------------------
> would be overkill... most of it's pretty rough work.
----------------------------------------
Definitely not a rough work device.
Lew
"John Grossbohlin" wrote:
> You've pretty much nailed what I need it for... hold pine frames
> together that will be laminated with hardboard or 3/8" ply, i.e,
> torsion boxes.
--------------------------------
If this were metal, it would be akin to tack welding.
Since it is only temporary, should work.
Lew
On Jan 29, 11:45=A0am, "John Grossbohlin"
<[email protected]> wrote:
> "JayPique" <[email protected]> wrote in message
>
> news:[email protected]...
>
> > I've got a Senco corrugated fastener gun. =A0For some jobs it works
> > fine, others not at all. =A0Generally good for things like softwood
> > frames that need to be held together temporarily until they get
> > laminated or further attached to something. =A0The fasteners aren't
> > structural themselves - you can bend them with your fingers. =A0But if
> > you use glue they pull the joint closed reasonably well and hold it
> > until dry. =A0What is your actual application?
> > JP
>
> You've pretty much nailed what I need it for... =A0hold pine frames toget=
her
> that will be laminated with hardboard or 3/8" ply, i.e, =A0torsion boxes.
>
> I've been thinking about another project where I could use it with oak
> veneered mdf. It's a wall paneling/wainscot project (a room full). I've g=
ot
> a huge pile of oak veneer--old thick stuff--and by using a vacuum press I
> would make up rails and stiles and panels. This makes me think hooking th=
e
> rails and styles together is doable:http://www.youtube.com/watch?v=3Dx1rr=
X1EfVqY=A0It's non-structural... the
> panels will sit in a rabet.
>
> There are some other things along the lines of the first on the horizon
> coming along too...
>
> I am mostly known for doing all kinds of handcut dovetails in my woodwork=
ing
> club. This this may seem like an odd addition to my arsenal of tools but =
it
> seems to be the right tool...
>
> John
That'd be a perfect application for that fastener.
On Jan 29, 1:02=A0am, "Lew Hodgett" <[email protected]> wrote:
> "John Grossbohlin" wrote:
> > Anybody have any experience with these?
>
> ----------------------------------------
> A little.
> ----------------------------------------> I've got a couple projects comi=
ng up where these are probably the
> > right tool for the job...
>
> ----------------------------------------
> I doubt that.
> ----------------------------------------> NOT fine furniture! LOL
>
> ----------------------------------------
> Or much of anything else IMHO.
>
> Don't expect them to carry much of a load.
>
> I'd go back to the thinking chair and start over.
> ----------------------------------------> would be overkill... most of it=
's pretty rough work.
>
> ----------------------------------------
> Definitely not a rough work device.
>
> Lew
NOT a rough working device, Lew? I take that as a typo?
On Jan 28, 9:36=A0pm, "John Grossbohlin"
<[email protected]> wrote:
> Anybody have any experience with these? =A0I've got a couple projects com=
ing
> up where these are probably the right tool for the job... NOT fine
> furniture! LOL =A0Biscuits would be way too slow and pocket screws would =
only
> save me glue drying time over the biscuits. Mortise and tenon or lap join=
ts
> would be overkill... most of it's pretty rough work.
>
> The Senco is pricy and way more than I need... the Rockler fasteners are =
too
> narrow for my purposes--only a 1/2" rather than the more typical 1" or so=
. I
> see tools by SpotNails and Air Locker are available. The Bostitch is
> interesting... a brand I've got experience with... coil nailer for framin=
g.
> I didn't find Porter Cable, Harbor Freight, or others tools.
>
> Recommendations? Thoughts?
>
> Thanks,
>
> John
Spotnails is adequate, I use(d) a Paslode MC10(??) Sometimes nothing
else will work as well as a corrugated fastener.
I would buy the Spotnails as the Paslode must be stupid money by now.
Performance in plywood can be erratic (due to grain direction changes)
and can splinter the hell out of hardwoods.
Making frames and cases out of poplar works well as does lengthening
of particle board panels like countertops. (1/2" fastener into 11/16
PB backed by a block of granite (slab of steel) as a back-stop.) These
type of nailers can kick like a mule hence make sure your work is very
well supported and (backstopped??)
Also not a good idea to use on MDF.
HTH
I've got a Senco corrugated fastener gun. For some jobs it works
fine, others not at all. Generally good for things like softwood
frames that need to be held together temporarily until they get
laminated or further attached to something. The fasteners aren't
structural themselves - you can bend them with your fingers. But if
you use glue they pull the joint closed reasonably well and hold it
until dry. What is your actual application?
JP
"John Grossbohlin" <[email protected]> wrote in message
news:[email protected]...
>
> "JayPique" <[email protected]> wrote in message
> news:[email protected]...
>> I've got a Senco corrugated fastener gun. For some jobs it works
>> fine, others not at all. Generally good for things like softwood
>> frames that need to be held together temporarily until they get
>> laminated or further attached to something. The fasteners aren't
>> structural themselves - you can bend them with your fingers. But if
>> you use glue they pull the joint closed reasonably well and hold it
>> until dry. What is your actual application?
>> JP
>
> You've pretty much nailed what I need it for... hold pine frames together that
> will be laminated with hardboard or 3/8" ply, i.e, torsion boxes.
>
> I've been thinking about another project where I could use it with oak veneered
> mdf. It's a wall paneling/wainscot project (a room full). I've got a huge pile of
> oak veneer--old thick stuff--and by using a vacuum press I would make up rails and
> stiles and panels. This makes me think hooking the rails and styles together is
> doable: http://www.youtube.com/watch?v=x1rrX1EfVqY It's non-structural... the
> panels will sit in a rabet.
>
> There are some other things along the lines of the first on the horizon coming
> along too...
>
> I am mostly known for doing all kinds of handcut dovetails in my woodworking club.
> This this may seem like an odd addition to my arsenal of tools but it seems to be
> the right tool...
>
> John
I've used 1/2" staples for holding the interior pieces when building torsion boxes
and they've worked satisfactorily for me. YMMV.
Art
> "Robatoy" <[email protected]> wrote in message
> news:bbb1dbd6-fda0-402c-b42a [email protected]...
> On Jan 29, 1:02 am, "Lew Hodgett" <[email protected]> wrote:
> > "John Grossbohlin" wrote:
> > > Anybody have any experience with these?
> > ----------------------------------------
> > Definitely not a rough work device.
>
> > Lew
> NOT a rough working device, Lew? I take that as a typo?
I was wondering the same thing....
"JayPique" <[email protected]> wrote in message
news:[email protected]...
> I've got a Senco corrugated fastener gun. For some jobs it works
> fine, others not at all. Generally good for things like softwood
> frames that need to be held together temporarily until they get
> laminated or further attached to something. The fasteners aren't
> structural themselves - you can bend them with your fingers. But if
> you use glue they pull the joint closed reasonably well and hold it
> until dry. What is your actual application?
> JP
You've pretty much nailed what I need it for... hold pine frames together
that will be laminated with hardboard or 3/8" ply, i.e, torsion boxes.
I've been thinking about another project where I could use it with oak
veneered mdf. It's a wall paneling/wainscot project (a room full). I've got
a huge pile of oak veneer--old thick stuff--and by using a vacuum press I
would make up rails and stiles and panels. This makes me think hooking the
rails and styles together is doable:
http://www.youtube.com/watch?v=x1rrX1EfVqY It's non-structural... the
panels will sit in a rabet.
There are some other things along the lines of the first on the horizon
coming along too...
I am mostly known for doing all kinds of handcut dovetails in my woodworking
club. This this may seem like an odd addition to my arsenal of tools but it
seems to be the right tool...
John