Gizmofiddler wrote:
> What are some techniques to precisely bore a 1/4" to 1/2" hole in the
> end of a 3/4" section of a hardwood mop handle? I want the holes to
> be in the exact center so I can use them as rollers.
> I am new to woodworking and I'm sure there must be a trick to this.
1. Secure a piece of wood to the DP table
2. Drill a 3/4 hole in it
3. Replace the 3/4 bit with the 1/4 or 1/2
4. Put your mop handle section in the 3/4 hole
5. Drill
IMO, you would do better with rollers greater in diameter...1 1/2 PVC pipe
works well, just cut a plywood plug to fit each end. The holes in the
plywood ends can be bushed with pieces of copper pipe but it isn't
necessary.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Brilliant idea "dadiOH"!
"dadiOH" <[email protected]> wrote in message
news:%otpg.2490$JZ1.947@trnddc01...
> Gizmofiddler wrote:
>> What are some techniques to precisely bore a 1/4" to 1/2" hole in the
>> end of a 3/4" section of a hardwood mop handle? I want the holes to
>> be in the exact center so I can use them as rollers.
>> I am new to woodworking and I'm sure there must be a trick to this.
>
> 1. Secure a piece of wood to the DP table
>
> 2. Drill a 3/4 hole in it
>
> 3. Replace the 3/4 bit with the 1/4 or 1/2
>
> 4. Put your mop handle section in the 3/4 hole
>
> 5. Drill
>
> IMO, you would do better with rollers greater in diameter...1 1/2 PVC pipe
> works well, just cut a plywood plug to fit each end. The holes in the
> plywood ends can be bushed with pieces of copper pipe but it isn't
> necessary.
>
>
> --
>
> dadiOH
> ____________________________
>
> dadiOH's dandies v3.06...
> ...a help file of info about MP3s, recording from
> LP/cassette and tips & tricks on this and that.
> Get it at http://mysite.verizon.net/xico
>
>
>
Make a drill jig:
A variation on "dadiOH"'s really good idea is to fasten a thick piece of
hardwood onto the drill press table. Then drill a 3/4" diameter hole about
half way into the thickness of the hardwood. Without moving the table
position, replace with 1/4" or 1/2" hole and drill thru.
Now unfasten the hardwood piece and place it on the 3/4" dowel to use as a
drill jig. Use the smaller diameter hole as a guide to drill the smaller
hole into the drill jig.
"Gizmofiddler" <[email protected]> wrote in message
news:[email protected]...
> What are some techniques to precisely bore a 1/4" to 1/2" hole in the end
> of
> a 3/4" section of a hardwood mop handle? I want the
"Australopithecus scobis" <[email protected]> wrote in message
>
> That's for a couple of holes. If you're making a whole bunch of copies,
> get a guide bushing. Lee Valley sells them. The guide bushing goes where
> the narrow hole is drilled in Mr Arthur's description. The metal bushing
> keeps the drill centered. Without the bushing, your wooden guide hole
> will get chewed up gradually.
I bought some and they work quite well.
http://www.leevalley.com/wood/page.aspx?c=2&p=32317&cat=1,180,42311,42321&ap=1
In article <[email protected]>,
"Frank Arthur" <[email protected]> wrote:
> Make a drill jig:
> A variation on "dadiOH"'s really good idea is to fasten a thick piece of
> hardwood onto the drill press table. Then drill a 3/4" diameter hole about
> half way into the thickness of the hardwood. Without moving the table
> position, replace with 1/4" or 1/2" hole and drill thru.
> Now unfasten the hardwood piece and place it on the 3/4" dowel to use as a
> drill jig. Use the smaller diameter hole as a guide to drill the smaller
> hole into the drill jig.
That's for a couple of holes. If you're making a whole bunch of copies,
get a guide bushing. Lee Valley sells them. The guide bushing goes where
the narrow hole is drilled in Mr Arthur's description. The metal bushing
keeps the drill centered. Without the bushing, your wooden guide hole
will get chewed up gradually.
--
"Keep your ass behind you."
Gizmofiddler (in [email protected]) said:
| What are some techniques to precisely bore a 1/4" to 1/2" hole in
| the end of a 3/4" section of a hardwood mop handle? I want the
| holes to be in the exact center so I can use them as rollers.
| I am new to woodworking and I'm sure there must be a trick to this.
|
| anyone?
The easy way is to feed the roller through the headstock of a lathe
and clamp it in a 3-jaw chuck, mount a drill in a drill chuck in the
tailstock, and feed the non-rotating drill bit into the rotating
roller.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto