Cutting 5 piece Padauk for a box the blade didn't want to retrace the
kerf to exit the block. I removed one drawer blank and started to try
to get the blade out. No luck with back of blade so turned teeth
first but still too much resistance. Turned on the saw and tried to
carefully follow the kerf but didn't quite make it without a couple of
gouges where the kerf wasn't followed.
Idea popped up this morning of removing the upper wheel cover with saw
unplugged and turn the wheel in reverse with teeth oriented so they
point opposite to the direction to make the cut while facing the kerf.
Thinking is the teeth points will be in the kerf but not cutting as
the blade will travel UP from the table and hopefully knock the
sawdust out of the kerf allowing the blade to be extracted without
risking the gouges made with the blade traveling in the cutting
direction.
Hoping someone has "plowed this row" and will share their experience.
How do BS box makers get the blade out after completing the first cut?
Have seen reference to slipping a wedge into the kerf to open it up
but that didn't work for me.
<[email protected]> wrote in message
> Cutting 5 piece Padauk for a box the blade didn't want to retrace the
> kerf to exit the block. snip
>
> Hoping someone has "plowed this row" and will share their experience.
> How do BS box makers get the blade out after completing the first cut?
> Have seen reference to slipping a wedge into the kerf to open it up
> but that didn't work for me.
If a wedge won't open the cut enough to allow an exit, you only have two
choices.
Cut through the Padauk, start over or cut the blade. BTW, this is not that
big a deal. Any competent blade shop can weld it back.
In the future, round and polish the back of the blade. It makes exiting the
kerf easy.
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com
Will round and polish the back of the blade prior to next box! Thanks.
On Thu, 29 Jun 2006 07:52:48 -0700, "Teamcasa" <[email protected]>
wrote:
><[email protected]> wrote in message
>> Cutting 5 piece Padauk for a box the blade didn't want to retrace the
>> kerf to exit the block. snip
>>
>> Hoping someone has "plowed this row" and will share their experience.
>> How do BS box makers get the blade out after completing the first cut?
>> Have seen reference to slipping a wedge into the kerf to open it up
>> but that didn't work for me.
>
>If a wedge won't open the cut enough to allow an exit, you only have two
>choices.
>Cut through the Padauk, start over or cut the blade. BTW, this is not that
>big a deal. Any competent blade shop can weld it back.
>In the future, round and polish the back of the blade. It makes exiting the
>kerf easy.
>
>Dave
>
>
>
> Posted Via Usenet.com Premium Usenet Newsgroup Services
>----------------------------------------------------------
> ** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
>----------------------------------------------------------
> http://www.usenet.com
Make an EXIT cut in an inconspicuous area. You should plan your cuts so
that you do not end up at a dead end.
<[email protected]> wrote in message
news:[email protected]...
> Cutting 5 piece Padauk for a box the blade didn't want to retrace the
> kerf to exit the block. I removed one drawer blank and started to try
> to get the blade out. No luck with back of blade so turned teeth
> first but still too much resistance. Turned on the saw and tried to
> carefully follow the kerf but didn't quite make it without a couple of
> gouges where the kerf wasn't followed.
>
> Idea popped up this morning of removing the upper wheel cover with saw
> unplugged and turn the wheel in reverse with teeth oriented so they
> point opposite to the direction to make the cut while facing the kerf.
> Thinking is the teeth points will be in the kerf but not cutting as
> the blade will travel UP from the table and hopefully knock the
> sawdust out of the kerf allowing the blade to be extracted without
> risking the gouges made with the blade traveling in the cutting
> direction.
>
> Hoping someone has "plowed this row" and will share their experience.
> How do BS box makers get the blade out after completing the first cut?
> Have seen reference to slipping a wedge into the kerf to open it up
> but that didn't work for me.
In article <[email protected]>, [email protected] wrote:
>Cutting 5 piece Padauk for a box the blade didn't want to retrace the
>kerf to exit the block. I removed one drawer blank and started to try
>to get the blade out. No luck with back of blade so turned teeth
>first but still too much resistance. Turned on the saw and tried to
>carefully follow the kerf but didn't quite make it without a couple of
>gouges where the kerf wasn't followed.
[...]
>Hoping someone has "plowed this row" and will share their experience.
>How do BS box makers get the blade out after completing the first cut?
My first guess is that you're using too wide a blade.
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.