I have The New Router Handbook by Patrick Spielman. On page 307 therein, the keys for
the dovetailed mitre cut are shown inserted into the dovetail cut across the corner
of the glued mitre joint. I wish to make that joint and the keys. Actually I wish to
make the key *stock* from which to cut the individual keys. Looking at their ends,
the keys appear to be truncated triangles with their bases deep into the glued mitre
joint. I do not have a good router table, but I do have a Crapsman metal table-top
affair for my old Crapsman 1/4" router. I hope to be able to make the stock with my
TS. Is there a 1/4" router bit which looks like this: > < to make the key stock?
That would appear to be dangerous though. Any suggestions will be appreciated.
Hoyt W.
patriarch <<patriarch>[email protected]> wrote in message news:<[email protected]>...
> It takes a standard router table and fence to do this safely, in my
> opinion.
I do it without. It certainly needs a jig, but given the size of
picture frames, I'm happier about clamping the jig to the frame and
using that as the guide than I am trying to feed a frame through my
table, whilst resting one corner on a sliding jig.
My jig is simply a triangle of MDF with two guide bars underneath and
a couple of stopped slots in the top for the cutter. I clamp it to the
outside of the frame, butted against the bars, and slide my router
along another bar on the top at 45 degrees. There are two slots, to
permit different frame stock widths (there's a bar either side, which
also makes it a very solid jig). Mine is dedicated to one router and
one baseplate size, but you could easily make it to run against the
edge with a router fence, rather than fit the guide bars.
For making the key stock, I just use a block plane. I'd probably make
up batches on the router table (many frames' worth) if I did this
regularly, but it's an easy enough task to hand-plane them from a
strip. It's only a short length, so keeping the size accurate over
that distance isn't too difficult.
"patriarch <" wrote:
<sniped>
> I think that the router method is covered in one of Doug Stowe's box making
> books, as well as in Gary Rogowski's Joinery book in the new Taunton
> Complete Illustrated Guide series. I'd go look it up, but those volumes
> are boxed right now, until I finish the new bookshelves for the den.
>
> It takes a standard router table and fence to do this safely, in my
> opinion. Yours may be up to it, but you'd have to be the judge.
> Essentially, you are making the inverse of the cut that the DT bit cut in
> the miter corner, so you want to use the same bit.
>
> Square up a piece of the key stock on your TS, then set your table to cut
> the first side of the key stock. The cut will be less than full height of
> the key stock, and look somewhat like the number 7. The excess height is
> important for holding the stock safely, and guiding against the fence, so
> don't trim it until the last. Now turn the stock around, adjust your fence
> for a light cut, and cut the '7' again. Sneak up on the fence adjustments,
> and take light passes, until your key stock fits your miter dovetail slot.
>
> Or you can do this with hand tools. That's how I often make the key stock
> for the mitered boxes I build. There's just not enough gain to be had in
> the setting up of all of the machines to do a small batch. The work is
> quiet, and, while I HAVE cut myself with a sharp plane iron, it only took a
> bandaid and a day to heal.
>
> Patriarch,
> enjoying the quiet
Thank you Patriarch. You helped me a lot. I only need to do a 7 cut on *both* sides
of the work piece with the TS. Or I could just use a the same 1/4" dovetail router
bit I use to cut the the opening, flip the stock and do it again. That should work -
perhaps.
Hoyt W.
Hoyt Weathers <[email protected]> wrote in
news:[email protected]:
> I have The New Router Handbook by Patrick Spielman. On page 307
> therein, the keys for the dovetailed mitre cut are shown inserted into
> the dovetail cut across the corner of the glued mitre joint. I wish to
> make that joint and the keys. Actually I wish to make the key *stock*
> from which to cut the individual keys. Looking at their ends, the keys
> appear to be truncated triangles with their bases deep into the glued
> mitre joint. I do not have a good router table, but I do have a
> Crapsman metal table-top affair for my old Crapsman 1/4" router. I
> hope to be able to make the stock with my TS. Is there a 1/4" router
> bit which looks like this: > < to make the key stock? That would
> appear to be dangerous though. Any suggestions will be appreciated.
>
> Hoyt W.
>
>
I think that the router method is covered in one of Doug Stowe's box making
books, as well as in Gary Rogowski's Joinery book in the new Taunton
Complete Illustrated Guide series. I'd go look it up, but those volumes
are boxed right now, until I finish the new bookshelves for the den.
It takes a standard router table and fence to do this safely, in my
opinion. Yours may be up to it, but you'd have to be the judge.
Essentially, you are making the inverse of the cut that the DT bit cut in
the miter corner, so you want to use the same bit.
Square up a piece of the key stock on your TS, then set your table to cut
the first side of the key stock. The cut will be less than full height of
the key stock, and look somewhat like the number 7. The excess height is
important for holding the stock safely, and guiding against the fence, so
don't trim it until the last. Now turn the stock around, adjust your fence
for a light cut, and cut the '7' again. Sneak up on the fence adjustments,
and take light passes, until your key stock fits your miter dovetail slot.
Or you can do this with hand tools. That's how I often make the key stock
for the mitered boxes I build. There's just not enough gain to be had in
the setting up of all of the machines to do a small batch. The work is
quiet, and, while I HAVE cut myself with a sharp plane iron, it only took a
bandaid and a day to heal.
Patriarch,
enjoying the quiet
Hoyt Weathers <[email protected]> wrote in
news:[email protected]:
> "patriarch <" wrote:
>
> <sniped>
>
>> I think that the router method is covered in one of Doug Stowe's box
>> making books, as well as in Gary Rogowski's Joinery book in the new
>> Taunton Complete Illustrated Guide series. I'd go look it up, but
>> those volumes are boxed right now, until I finish the new bookshelves
>> for the den.
>>
>> It takes a standard router table and fence to do this safely, in my
>> opinion. Yours may be up to it, but you'd have to be the judge.
>> Essentially, you are making the inverse of the cut that the DT bit
>> cut in the miter corner, so you want to use the same bit.
>>
>> Square up a piece of the key stock on your TS, then set your table to
>> cut the first side of the key stock. The cut will be less than full
>> height of the key stock, and look somewhat like the number 7. The
>> excess height is important for holding the stock safely, and guiding
>> against the fence, so don't trim it until the last. Now turn the
>> stock around, adjust your fence for a light cut, and cut the '7'
>> again. Sneak up on the fence adjustments, and take light passes,
>> until your key stock fits your miter dovetail slot.
>>
>> Or you can do this with hand tools. That's how I often make the key
>> stock for the mitered boxes I build. There's just not enough gain to
>> be had in the setting up of all of the machines to do a small batch.
>> The work is quiet, and, while I HAVE cut myself with a sharp plane
>> iron, it only took a bandaid and a day to heal.
>>
>> Patriarch,
>> enjoying the quiet
>
> Thank you Patriarch. You helped me a lot. I only need to do a 7 cut on
> *both* sides of the work piece with the TS. Or I could just use a the
> same 1/4" dovetail router bit I use to cut the the opening, flip the
> stock and do it again. That should work - perhaps.
>
> Hoyt W.
>
I was thinking the router method. I haven't tried the tablesaw approach,
but I consider the router to be somewhat more precise when I'm nudging a
piece to a very close fit.
But yeah, that's the ticket.
Patriarch