Hello:
When bulding my workbench (truss rod construstion), I made the mistake
of tapping the stubborn truss rod ends with a hammer to move them in
place. As a result, the threads on the ends were smashed and will not
accept a nut. I tried to use a triangular file to "recreate" the
grooves, but this only made it stripped! Is there any way for me to
repair the ends or rethread them? I know this is not rec.metalworking,
but I figured someone here has done the same thing. Please list
multiple solutions if there are any. Thanks in advance!
Bob
If possible cut 1/8 in or so off the end with a hacksaw then file the end or
go the hardware store and get a threading die and run that down the threads.
Good luck Russ
<[email protected]> wrote in message
news:[email protected]...
> Hello:
>
> When bulding my workbench (truss rod construstion), I made the mistake
> of tapping the stubborn truss rod ends with a hammer to move them in
> place. As a result, the threads on the ends were smashed and will not
> accept a nut. I tried to use a triangular file to "recreate" the
> grooves, but this only made it stripped! Is there any way for me to
> repair the ends or rethread them? I know this is not rec.metalworking,
> but I figured someone here has done the same thing. Please list
> multiple solutions if there are any. Thanks in advance!
>
> Bob
>
They make a thread restoring file you could try or you can possibly clean up
the threads by running a die over them.
Describe the rod you are using for a truss.
--
Roger Shoaf
About the time I had mastered getting the toothpaste back in the tube, then
they come up with this striped stuff.
<[email protected]> wrote in message
news:[email protected]...
> Hello:
>
> When bulding my workbench (truss rod construstion), I made the mistake
> of tapping the stubborn truss rod ends with a hammer to move them in
> place. As a result, the threads on the ends were smashed and will not
> accept a nut. I tried to use a triangular file to "recreate" the
> grooves, but this only made it stripped! Is there any way for me to
> repair the ends or rethread them? I know this is not rec.metalworking,
> but I figured someone here has done the same thing. Please list
> multiple solutions if there are any. Thanks in advance!
>
> Bob
>
If you have access to a tap & die set, you can 'chase' the threads back
into their original condition (or so) with the appropriatly sized die--
to find out the size, you can use the supplied nut & test - by hand &
gently with various sized taps until the correct one will easily screw
on to the tap. You may have to round over the peened end of the rod
slightly with a file. Most dies have an end that is larger than the
finished thread size. Screw that end on first. If you don't have a
die set, any decent machine shop can rethread the end for you on the
lathe. Hope this helps.
Duane Bozarth wrote:
> "Phil at small (vs at large)" wrote:
> >
> ...
> > .... any decent machine shop can rethread the end for you on the
lathe.
>
> Don't think they would have a die? :)
>
> By the time he pays the machine setup fee, he'll have bought the rod
> several times over...
Or the start of a nice little die/tap set--always good to have around.
Dan
[email protected] wrote:
>
> Hello:
>
> When bulding my workbench (truss rod construstion), I made the mistake
> of tapping the stubborn truss rod ends with a hammer to move them in
> place. As a result, the threads on the ends were smashed and will not
> accept a nut. I tried to use a triangular file to "recreate" the
> grooves, but this only made it stripped! Is there any way for me to
> repair the ends or rethread them? I know this is not rec.metalworking,
> but I figured someone here has done the same thing. Please list
> multiple solutions if there are any. Thanks in advance!
1. Get a die and re-cut them...
2. If you've not torn them up too badly, file off enough to get past the
bad portion and go on..
3. Thread-cutting file...
4. Variations on above...
As a "trick", next time you need to do such an "adjustment", thread a
nut on the bolt/rod first and use either a wood block or a soft-face
mallet to drive...
"Phil at small (vs at large)" wrote:
>
> Thought of that after I posted-- and you were so kind to remind me. I
> always think most people have more bucks than me lol-- Anyway, I like
> the post below yours best-- simple simple simple.
As long as there is enough extra length to implement it, of course... :)
It's steel. Re-thread the end with a thread chaser or a thread restoration
file.
Worst case, have it cut, weld a new section on.
Dave
<[email protected]> wrote in message
news:[email protected]...
> Hello:
>
> When bulding my workbench (truss rod construstion), I made the mistake
> of tapping the stubborn truss rod ends with a hammer to move them in
> place. As a result, the threads on the ends were smashed and will not
> accept a nut. I tried to use a triangular file to "recreate" the
> grooves, but this only made it stripped! Is there any way for me to
> repair the ends or rethread them? I know this is not rec.metalworking,
> but I figured someone here has done the same thing. Please list
> multiple solutions if there are any. Thanks in advance!
>
> Bob
>
On 17 Jan 2005 08:18:08 -0800, [email protected] wrote:
>Hello:
>
>When bulding my workbench (truss rod construstion), I made the mistake
>of tapping the stubborn truss rod ends with a hammer to move them in
>place. As a result, the threads on the ends were smashed and will not
>accept a nut. I tried to use a triangular file to "recreate" the
>grooves, but this only made it stripped! Is there any way for me to
>repair the ends or rethread them? I know this is not rec.metalworking,
>but I figured someone here has done the same thing. Please list
>multiple solutions if there are any. Thanks in advance!
>
>Bob
rethreading file.
Try tapering the end of the rod. I've done that in similar situations
with success.
[email protected] wrote:
> Hello:
>
> When bulding my workbench (truss rod construstion), I made the mistake
> of tapping the stubborn truss rod ends with a hammer to move them in
> place. As a result, the threads on the ends were smashed and will not
> accept a nut. I tried to use a triangular file to "recreate" the
> grooves, but this only made it stripped! Is there any way for me to
> repair the ends or rethread them? I know this is not rec.metalworking,
> but I figured someone here has done the same thing. Please list
> multiple solutions if there are any. Thanks in advance!
>
> Bob
>
On 17 Jan 2005 08:18:08 -0800, [email protected] wrote:
>Hello:
>
>When bulding my workbench (truss rod construstion), I made the mistake
>of tapping the stubborn truss rod ends with a hammer to move them in
>place. As a result, the threads on the ends were smashed and will not
>accept a nut. I tried to use a triangular file to "recreate" the
>grooves, but this only made it stripped! Is there any way for me to
>repair the ends or rethread them? I know this is not rec.metalworking,
>but I figured someone here has done the same thing. Please list
>multiple solutions if there are any. Thanks in advance!
>
>Bob
Simplest way is to file or grind the end that is damaged flat until
the damaged area is cleaned up. Forget about "triangular files" they
are generally the wrong pitch angle anyway. You could always remove
the rod and start a die nut of the appropriate size from the opposite
end and run it the entire lenght of the rod but you will likely still
be faced with grinding/filing the damaged end done because the die nut
won't cut new thred in rod that is grossly swelled oversize.