I've been thinking... a band clamp is essentially a ratcheting truck tie
down with blocks to hold the corners, right? So is there anything special
to the band clamp that would preclude the use of a tie down as a band
clamp? (Besides the blocks, but they're easily made.)
Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as some
writers are incorrigible.
To email me directly, send a message to puckdropper (at) fastmail.fm
"-MIKE-" wrote
>
> There was a dude who was pushing the stock behind the blade, his sleeve
> got between the wood and the anti-kickback claw, lifting the claw off
> the wood, while at the same time the sleeve got caught in the wood.
>
> Take a guess what happened next. :-)
> --
Is this the guy who got abducted by aliens?
Or attacked by a band of rabid drummers?
Or the table saw chewed his entire arm off with its safety equiment?
Or....... ?
Limp Arbor <[email protected]> wrote in news:6452602d-575d-4f4c-b796-
[email protected]:
*snip*
>
> Then cats will start sleeping with dogs...
And we'll see the 300' tall StayPuft Marshmallow Man! (That /was/ a
Ghostbusters reference, wasn't it?)
Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as some
writers are incorrigible.
To email me directly, send a message to puckdropper (at) fastmail.fm
"[email protected]" <[email protected]> wrote in news:4271afab-
[email protected]:
> I have used the truck tie downs for band clamps many times. I use
> them with cauls when gluing/repairing odd shaped pieces. Not my
> idea... I read about it somewhere a while back.
>
> Then I got the idea of using the ratchet style tie downs to glue
> bigger things. Doors, gluing long trims to surfaces, indoor/outdoor
> furniture repairs, etc. Anything I couldn't quite get easily with my
> current clamps. For me, the ratcheting tie downs turned out to be
> much more handy as clamps than they did tie downs.
>
> See if you can find the small ones that don't have the hooks on them.
> I had some with 1" wide light weight straps (500# work load / 750#
> break) and they were flexible enough to work great.
>
> One of the first things I glued back together with was an oversized
> door.
> I didn't have by big clamps with me and this was a custom made entry
> door that was 40 inches wide or some such. As the main entry it was
> beat to hell and the bottom rail/kick panel was loose and coming off.
>
> With the door laying flat on the horses, I glued up the joint, and put
> a straight piece of 2x4 that spanned stile to stile on edge on both
> sides (loose, I had a helper). The 2x4 on each side was there to make
> sure I didn't bow or cup the door, or make a crooked joint. That's
> why it was on both sides spanning the stiles.
>
> I put the nylon ribbon of the clamp on the edge of the 2x4 on both
> sides. Clamped it up with the ratchet, then ran a couple of 3 1/2"
> deck screws from the bottom of the kick panel into the stiles and left
> it overnight.
>
> It didn't flex or move a bit. The 2X4 spines did the trick.
>
> The best thing about these little ratchet clamps as opposed to
> something they sell to wood workers is the price. I paid something
> like $4 a piece in a four pack at a hardware store. If the same
> clamp, a "multipurpose flexible band style clamp for fine woodworking"
> is sold to the woodworking community, they would surely be $20 a
> piece.
>
> Robert
Thanks Robert. The hooks would seem to be a bit of an issue, but a few
well placed cauls would take care of that.
Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as
some writers are incorrigible.
To email me directly, send a message to puckdropper (at) fastmail.fm
On Mar 31, 3:19=A0pm, "Upscale" <[email protected]> wrote:
> http://www.leevalley.com/wood/page.aspx?c=3D1&p=3D31160&cat=3D1,43838
Wow.. good eye!
Those are the EXACT clamps.... uh... er.... tie downs that I have,
even down to the cadmium plating.
Add shipping into the price and I wasn't off too much on the price,
either!
Robert
On Mar 31, 4:41=A0pm, "Lee Michaels" <leemichaels*[email protected]>
wrote:
> "-MIKE-" =A0wrote
>
> > There was a dude who was pushing the stock behind the blade, his sleeve
> > got between the wood and the anti-kickback claw, lifting the claw off
> > the wood, while at the same time the sleeve got caught in the wood.
>
> > Take a guess what happened next. =A0 :-)
> > --
>
> Is this the guy who got abducted by aliens?
>
> Or attacked by a band of rabid drummers?
>
> Or the table saw chewed his entire arm off with its safety equiment?
>
> Or....... =A0?
Gettin' a chuckle out of that one....
I usually try to work zombies in somewhere myself ;^)
Robert
I have used the truck tie downs for band clamps many times. I use
them with cauls when gluing/repairing odd shaped pieces. Not my
idea... I read about it somewhere a while back.
Then I got the idea of using the ratchet style tie downs to glue
bigger things. Doors, gluing long trims to surfaces, indoor/outdoor
furniture repairs, etc. Anything I couldn't quite get easily with my
current clamps. For me, the ratcheting tie downs turned out to be
much more handy as clamps than they did tie downs.
See if you can find the small ones that don't have the hooks on them.
I had some with 1" wide light weight straps (500# work load / 750#
break) and they were flexible enough to work great.
One of the first things I glued back together with was an oversized
door.
I didn't have by big clamps with me and this was a custom made entry
door that was 40 inches wide or some such. As the main entry it was
beat to hell and the bottom rail/kick panel was loose and coming off.
With the door laying flat on the horses, I glued up the joint, and put
a straight piece of 2x4 that spanned stile to stile on edge on both
sides (loose, I had a helper). The 2x4 on each side was there to make
sure I didn't bow or cup the door, or make a crooked joint. That's
why it was on both sides spanning the stiles.
I put the nylon ribbon of the clamp on the edge of the 2x4 on both
sides. Clamped it up with the ratchet, then ran a couple of 3 1/2"
deck screws from the bottom of the kick panel into the stiles and left
it overnight.
It didn't flex or move a bit. The 2X4 spines did the trick.
The best thing about these little ratchet clamps as opposed to
something they sell to wood workers is the price. I paid something
like $4 a piece in a four pack at a hardware store. If the same
clamp, a "multipurpose flexible band style clamp for fine woodworking"
is sold to the woodworking community, they would surely be $20 a
piece.
Robert
On Mar 31, 3:19=A0pm, Puckdropper <puckdropper(at)yahoo(dot)com> wrote:
> I've been thinking... a band clamp is essentially a ratcheting truck tie
> down with blocks to hold the corners, right? =A0So is there anything spec=
ial
> to the band clamp that would preclude the use of a tie down as a band
> clamp? =A0
Yes, it is a tie down not a clamp.
Next thing you'll be saying is:
You don't need to use gold-plated Monster cables for your AV
equipment.
or
You can use SS screws from a hardware store on your boat instead of
the ones sold at the marine supply house.
or
...
Then cats will start sleeping with dogs...
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Upscale wrote:
>> <[email protected]> wrote in message
>>> See if you can find the small ones that don't have the hooks on them.
>>> I had some with 1" wide light weight straps (500# work load / 750#
>>> break) and they were flexible enough to work great.
>>
>> http://www.leevalley.com/wood/page.aspx?c=1&p=31160&cat=1,43838
>>
>
> Check out the gap in the joint in pic above.
>
> I love how pictures in ads for tools always show poor results or
> technique and/or egregious safety no-no's.
>
> May favorite was a guy using a table saw with thick cotton gloves and a
> long flannel shirt sleeves down to his wrists.
While I don't advocate wearing either while operating any power tool. The
lathe, drill press and such tools are far more dangerous to wear loose
clothing and or gloves around than a TS. The TS blade will actually cut
though the cotton with no exciting results. This conversation went around
about 8 years ago and I conducted an experiment with a cotton and leather
glove. I pushed the glove into a spinning TS blade with a stick. The blade
left a 1/8" wide kerf in a finger. The finger did not bounce, flutter, or
get dragged into the blade. The glove stopped proceeding and sat with the
blade spinning through the finger when I stopped pushing.
Again I don't recommend the use of gloves with a TS, there are several other
things that could happen.
<[email protected]> wrote in message
> See if you can find the small ones that don't have the hooks on them.
> I had some with 1" wide light weight straps (500# work load / 750#
> break) and they were flexible enough to work great.
http://www.leevalley.com/wood/page.aspx?c=1&p=31160&cat=1,43838
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>> While I don't advocate wearing either while operating any power tool.
>> The lathe, drill press and such tools are far more dangerous to wear
>> loose clothing and or gloves around than a TS. The TS blade will
>> actually cut though the cotton with no exciting results. This
>> conversation went around about 8 years ago and I conducted an experiment
>> with a cotton and leather glove. I pushed the glove into a spinning TS
>> blade with a stick. The blade left a 1/8" wide kerf in a finger. The
>> finger did not bounce, flutter, or get dragged into the blade. The glove
>> stopped proceeding and sat with the blade spinning through the finger
>> when I stopped pushing.
>>
>> Again I don't recommend the use of gloves with a TS, there are several
>> other things that could happen.
>
> There was a dude who was pushing the stock behind the blade, his sleeve
> got between the wood and the anti-kickback claw, lifting the claw off
> the wood, while at the same time the sleeve got caught in the wood.
>
> Take a guess what happened next. :-)
>
YEAH! That is one of those "several other things" that could happen.
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>>
>>
>> YEAH! That is one of those "several other things" that could happen.
>
> Dude, you went through this whole schpeal about how it's not dangerous,
> then you say it's dangerous. :-p
>
Reread all of what I originally posted concerning the glove and saw
experiment. I just repeated what I said.
Puckdropper wrote:
> I've been thinking... a band clamp is essentially a ratcheting truck tie
> down with blocks to hold the corners, right? So is there anything special
> to the band clamp that would preclude the use of a tie down as a band
> clamp? (Besides the blocks, but they're easily made.)
Nothing other than size/bulkiness. Some are pretty unhandy, some
reasonably decently designed for the use.
--
"dpb" <[email protected]> wrote in message news:[email protected]...
> Puckdropper wrote:
> > I've been thinking... a band clamp is essentially a ratcheting truck =
tie=20
> > down with blocks to hold the corners, right? So is there anything =
special=20
> > to the band clamp that would preclude the use of a tie down as a =
band=20
> > clamp? (Besides the blocks, but they're easily made.)
>=20
> Nothing other than size/bulkiness. Some are pretty unhandy, some=20
> reasonably decently designed for the use.
>=20
> --
Beyond this, will only add one more caution:
Truck tie downs can generate a lot of pressure (the good ones).
A lot more than a wooddorkers band clamp.
Be gentle and only use a modicum of pressure.
P D Q
Upscale wrote:
> <[email protected]> wrote in message
>> See if you can find the small ones that don't have the hooks on them.
>> I had some with 1" wide light weight straps (500# work load / 750#
>> break) and they were flexible enough to work great.
>
> http://www.leevalley.com/wood/page.aspx?c=1&p=31160&cat=1,43838
>
Check out the gap in the joint in pic above.
I love how pictures in ads for tools always show poor results or
technique and/or egregious safety no-no's.
May favorite was a guy using a table saw with thick cotton gloves and a
long flannel shirt sleeves down to his wrists.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Leon wrote:
> While I don't advocate wearing either while operating any power tool. The
> lathe, drill press and such tools are far more dangerous to wear loose
> clothing and or gloves around than a TS. The TS blade will actually cut
> though the cotton with no exciting results. This conversation went around
> about 8 years ago and I conducted an experiment with a cotton and leather
> glove. I pushed the glove into a spinning TS blade with a stick. The blade
> left a 1/8" wide kerf in a finger. The finger did not bounce, flutter, or
> get dragged into the blade. The glove stopped proceeding and sat with the
> blade spinning through the finger when I stopped pushing.
>
> Again I don't recommend the use of gloves with a TS, there are several other
> things that could happen.
>
There was a dude who was pushing the stock behind the blade, his sleeve
got between the wood and the anti-kickback claw, lifting the claw off
the wood, while at the same time the sleeve got caught in the wood.
Take a guess what happened next. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Lee Michaels wrote:
> "-MIKE-" wrote
>> There was a dude who was pushing the stock behind the blade, his sleeve
>> got between the wood and the anti-kickback claw, lifting the claw off
>> the wood, while at the same time the sleeve got caught in the wood.
>>
>> Take a guess what happened next. :-)
>> --
> Is this the guy who got abducted by aliens?
>
> Or attacked by a band of rabid drummers?
>
> Or the table saw chewed his entire arm off with its safety equiment?
>
> Or....... ?
>
LMAO!
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Leon wrote:
>
>
> YEAH! That is one of those "several other things" that could happen.
>
>
Dude, you went through this whole schpeal about how it's not dangerous,
then you say it's dangerous. :-p
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
Puckdropper wrote:
> I've been thinking... a band clamp is essentially a ratcheting truck tie
> down with blocks to hold the corners, right? So is there anything special
> to the band clamp that would preclude the use of a tie down as a band
> clamp? (Besides the blocks, but they're easily made.)
My shop band clamps ARE ratchet straps...
I hook the ends together in a spot that doesn't interfere with the work,
pull it tight, and ratchet in the pressure.
"Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
news:[email protected]...
> I've been thinking... a band clamp is essentially a ratcheting truck tie
> down with blocks to hold the corners, right? So is there anything special
> to the band clamp that would preclude the use of a tie down as a band
> clamp? (Besides the blocks, but they're easily made.)
>
You certainly can. In fact, this one time, at band clamp.....
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>> While I don't advocate wearing either while operating any power tool.
>> The lathe, drill press and such tools are far more dangerous to wear
>> loose clothing and or gloves around than a TS. The TS blade will
>> actually cut though the cotton with no exciting results. This
>> conversation went around about 8 years ago and I conducted an experiment
>> with a cotton and leather glove. I pushed the glove into a spinning TS
>> blade with a stick. The blade left a 1/8" wide kerf in a finger. The
>> finger did not bounce, flutter, or get dragged into the blade. The glove
>> stopped proceeding and sat with the blade spinning through the finger
>> when I stopped pushing.
>>
>> Again I don't recommend the use of gloves with a TS, there are several
>> other things that could happen.
>
> There was a dude who was pushing the stock behind the blade, his sleeve
> got between the wood and the anti-kickback claw, lifting the claw off
> the wood, while at the same time the sleeve got caught in the wood.
>
> Take a guess what happened next. :-)
He can no longer count to ten?
Just my guess, Rich
"Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
news:[email protected]...
> I've been thinking... a band clamp is essentially a ratcheting truck tie
> down with blocks to hold the corners, right? So is there anything special
> to the band clamp that would preclude the use of a tie down as a band
> clamp? (Besides the blocks, but they're easily made.)
>
> Puckdropper
> --
> On Usenet, no one can hear you laugh. That's a good thing, though, as
> some
> writers are incorrigible.
>
> To email me directly, send a message to puckdropper (at) fastmail.fm
Yes you can use them and they will provide the same pressure provided you do
not get the pull to tighten style. You want the ratchet style.