Hello,
I'm in the process of rebuilding a deck and have posted some other
questions. Thanks again to those who responded.
In shopping around for decking material, I found a place called Uncle
Hilde's Lumber Outlet that is located in New Hampshire. Has anyone here had
any experience, either good, bad, or indifferent, with them?
Out of necessity, I'm shopping price and was surprised at the low prices
that they are showing for the ironwoods such as Ipe, Meranti, or Tigerwood.
I thought that I had read on their site that the reason for their low prices
was due to the fact that the decking only comes in 8 ft. lengths. Upon
closer scrutiny, I can't seem to find where I read that.
In my case, I need to cover a 16' wide X 20' long deck. The 20' dimension
runs parallel to the house. Ideally, 20' long deck boards would do the job,
but at a substantially higher cost. I believe that Advantage Lumber, another
site that I looked at, adds an up charge of $1 per linear ft. for boards
over 19' and 20'. Too much for my budget.
It was suggested that I split the area into basically two 16' X 10' sections
by installing a center deck board perpendicular to the house and then
covering the two sections with 10' long deck boards. Not a bad idea. Another
suggestion was to go with 12' and 8' deck boards and stagger the joints.
That would work too, I suppose, however, I like the first suggestion better.
I also looked for some sort of calculator to see if I could play around with
various deck board sizes (both lengths & widths) and layouts, but couldn't
find one. Perhaps one doesn't exist.
Any feedback posted to the group would be greatly appreciated. Thanks in
advance.
Peter.
"Peter Bogiatzidis" <[email protected]> wrote in
news:[email protected]:
> Hello,
>
> I'm in the process of rebuilding a deck and have posted some other
> questions. Thanks again to those who responded.
>
> In shopping around for decking material, I found a place called Uncle
> Hilde's Lumber Outlet that is located in New Hampshire. Has anyone
> here had any experience, either good, bad, or indifferent, with them?
>
> Out of necessity, I'm shopping price and was surprised at the low
> prices that they are showing for the ironwoods such as Ipe, Meranti,
> or Tigerwood. I thought that I had read on their site that the reason
> for their low prices was due to the fact that the decking only comes
> in 8 ft. lengths. Upon closer scrutiny, I can't seem to find where I
> read that.
>
> In my case, I need to cover a 16' wide X 20' long deck. The 20'
> dimension runs parallel to the house. Ideally, 20' long deck boards
> would do the job, but at a substantially higher cost. I believe that
> Advantage Lumber, another site that I looked at, adds an up charge of
> $1 per linear ft. for boards over 19' and 20'. Too much for my budget.
>
> It was suggested that I split the area into basically two 16' X 10'
> sections by installing a center deck board perpendicular to the house
> and then covering the two sections with 10' long deck boards. Not a
> bad idea. Another suggestion was to go with 12' and 8' deck boards and
> stagger the joints. That would work too, I suppose, however, I like
> the first suggestion better.
>
> I also looked for some sort of calculator to see if I could play
> around with various deck board sizes (both lengths & widths) and
> layouts, but couldn't find one. Perhaps one doesn't exist.
>
> Any feedback posted to the group would be greatly appreciated. Thanks
> in advance.
>
> Peter.
If I remember correctly, we made our first home's deck with 4 sections.
We had a kitchen door roughly in the middle, and there I laid the boards
diagonally in a V pattern going away from the door. Boards perpendicular
to the width separate the V-section from the 2 sides where the boards ran
parallel to the house. It provided a bit of a pattern to break the
monotony of the large deck.
--
Best regards
Han
email address is invalid
"Peter Bogiatzidis" wrote in message
news:[email protected]...
Hello,
I'm in the process of rebuilding a deck and have posted some other
questions. Thanks again to those who responded.
In shopping around for decking material, I found a place called Uncle
Hilde's Lumber Outlet that is located in New Hampshire. Has anyone here had
any experience, either good, bad, or indifferent, with them?
Out of necessity, I'm shopping price and was surprised at the low prices
that they are showing for the ironwoods such as Ipe, Meranti, or Tigerwood.
I thought that I had read on their site that the reason for their low prices
was due to the fact that the decking only comes in 8 ft. lengths. Upon
closer scrutiny, I can't seem to find where I read that.
In my case, I need to cover a 16' wide X 20' long deck. The 20' dimension
runs parallel to the house. Ideally, 20' long deck boards would do the job,
but at a substantially higher cost. I believe that Advantage Lumber, another
site that I looked at, adds an up charge of $1 per linear ft. for boards
over 19' and 20'. Too much for my budget.
It was suggested that I split the area into basically two 16' X 10' sections
by installing a center deck board perpendicular to the house and then
covering the two sections with 10' long deck boards. Not a bad idea. Another
suggestion was to go with 12' and 8' deck boards and stagger the joints.
That would work too, I suppose, however, I like the first suggestion better.
I also looked for some sort of calculator to see if I could play around with
various deck board sizes (both lengths & widths) and layouts, but couldn't
find one. Perhaps one doesn't exist.
Any feedback posted to the group would be greatly appreciated. Thanks in
advance.
Peter.
==================
One possibility is to vary the splits into regular pattern breaks
like:
16'+4', 4'+16', repeat giving one broken, but visually lined up cracks at
each
or better yet
16'+4', 8'+12', 12'+8', 4'+16' giving four regularly spaced cracks with
larger gaps between repetitive rows.
Do it in multiples of 4' and the lumber should work out economically an look
like it was meant to be that way by design.
--
Eric
"Morgans" wrote in message news:xWG%[email protected]...
"Eric" wrote
One possibility is to vary the splits into regular pattern breaks
like:
16'+4', 4'+16', repeat giving one broken, but visually lined up cracks at
each
or better yet
16'+4', 8'+12', 12'+8', 4'+16' giving four regularly spaced cracks with
larger gaps between repetitive rows.
Do it in multiples of 4' and the lumber should work out economically an look
like it was meant to be that way by design.
--
Eric
----------------------------------------------------------------------------------------
That is how I would do it. I have to admit that I am somewhat anal about
keeping the pattern breaks going.
-- Jim in NC
===============
Yeah start a pattern like that and have to break it! It looks like hell to
me.
(maybe `hell` should have a capital on it)
--
Eric
"Eric" wrote
One possibility is to vary the splits into regular pattern breaks
like:
16'+4', 4'+16', repeat giving one broken, but visually lined up cracks at
each
or better yet
16'+4', 8'+12', 12'+8', 4'+16' giving four regularly spaced cracks with
larger gaps between repetitive rows.
Do it in multiples of 4' and the lumber should work out economically an look
like it was meant to be that way by design.
--
Eric
----------------------------------------------------------------------------------------
That is how I would do it. I have to admit that I am somewhat anal about
keeping the pattern breaks going.
-- Jim in NC