This seems so obvious that I can't imagine others haven't done it, but while
researching bandsaws in the google archives, I saw many posts where people had
problems putting the frame up on the stand and needing 2-3 people to help. So
I thought at least a few people would benefit from this procedure. I just put
together my Ridgid bandsaw and was able to do it easily on my own.
Basically, I just left the frame sitting horizontally on it's side in the box.
I removed all the other parts, and cut off the side of the box and the packing
which would be below the frame if it were standing up. I then assembled the
stand and laid it horizontally on the floor next to the bottom of the frame,
which was now peaking out of the box. I had to prop the frame up a little by
putting some twoby's underneath the remains of the box, then was able to line
up the holes in the stand with the bottom of the frame. Then I just tightened
the bolts horizontally.
I walked around the saw, tilted it up from the top, and it went right up. I
was worried about tilting it like that because I didn't know if two legs
diagonally would support the frame whlie it was going up, but there really was
no problem and it felt sturdy the whole time. Took almost no effort at all.
Jon
Tina wrote:
> Thanks for that post...I plan with a neighbor to get my New Jet 16" bandsaw
> assembled this weekend and this info helps
> Tina
>
> "Jon Shelley" <[email protected]> wrote in message
> news:[email protected]...
> > This seems so obvious that I can't imagine others haven't done it, but
> while
> > researching bandsaws in the google archives, I saw many posts where people
> had
> > problems putting the frame up on the stand and needing 2-3 people to help.
> So
> > I thought at least a few people would benefit from this procedure. I just
> put
> > together my Ridgid bandsaw and was able to do it easily on my own.
> >
> > Basically, I just left the frame sitting horizontally on it's side in the
> box.
> > I removed all the other parts, and cut off the side of the box and the
> packing
> > which would be below the frame if it were standing up. I then assembled
> the
> > stand and laid it horizontally on the floor next to the bottom of the
> frame,
> > which was now peaking out of the box. I had to prop the frame up a little
> by
> > putting some twoby's underneath the remains of the box, then was able to
> line
> > up the holes in the stand with the bottom of the frame. Then I just
> tightened
> > the bolts horizontally.
> >
> > I walked around the saw, tilted it up from the top, and it went right up.
> I
> > was worried about tilting it like that because I didn't know if two legs
> > diagonally would support the frame whlie it was going up, but there really
> was
> > no problem and it felt sturdy the whole time. Took almost no effort at
> all.
> >
> >
> > Jon
Actually, this info helps not at all with the Jet 16", which is a
European pattern unit, not a two part unit with a cast iron top. Your
Jet will come almost completely assembled, except possible for the
table and the motor (the motor will probably already be mounted, but
may not). It will arrive standing up, and if it doesn't, you had better
talk to the shipper. All you should need to do is install the table
(and, maybe, the motor). No lifting of heavy items is needed (not that
the table and motor are light, but in cast iron bandsaws, the upper,
cast iron, part is much heavier than the lower stand).
"dicko" <[email protected]> wrote in message
news:[email protected]...
> On 19 Aug 2005 11:17:05 -0700, "Charlie Self" <[email protected]>
> wrote:
>
> >
> >Tina wrote:
> >> Thanks for that post...I plan with a neighbor to get my New Jet 16"
bandsaw
> >> assembled this weekend and this info helps
> >> Tina
> >>
> >> "Jon Shelley" <[email protected]> wrote in message
> >> news:[email protected]...
> >> > This seems so obvious that I can't imagine others haven't done it,
but
> >> while
> >> > researching bandsaws in the google archives, I saw many posts where
people
> >> had
> >> > problems putting the frame up on the stand and needing 2-3 people to
help.
> >> So
> >> > I thought at least a few people would benefit from this procedure. I
just
> >> put
> >> > together my Ridgid bandsaw and was able to do it easily on my own.
> >> >
> >> > Basically, I just left the frame sitting horizontally on it's side in
the
> >> box.
> >> > I removed all the other parts, and cut off the side of the box and
the
> >> packing
> >> > which would be below the frame if it were standing up. I then
assembled
> >> the
> >> > stand and laid it horizontally on the floor next to the bottom of the
> >> frame,
> >> > which was now peaking out of the box. I had to prop the frame up a
little
> >> by
> >> > putting some twoby's underneath the remains of the box, then was able
to
> >> line
> >> > up the holes in the stand with the bottom of the frame. Then I just
> >> tightened
> >> > the bolts horizontally.
> >> >
> >> > I walked around the saw, tilted it up from the top, and it went right
up.
> >> I
> >> > was worried about tilting it like that because I didn't know if two
legs
> >> > diagonally would support the frame whlie it was going up, but there
really
> >> was
> >> > no problem and it felt sturdy the whole time. Took almost no effort
at
> >> all.
> >> >
> >> >
> >> > Jon
> >
> >Actually, this info helps not at all with the Jet 16", which is a
> >European pattern unit, not a two part unit with a cast iron top. Your
> >Jet will come almost completely assembled, except possible for the
> >table and the motor (the motor will probably already be mounted, but
> >may not). It will arrive standing up, and if it doesn't, you had better
> >talk to the shipper. All you should need to do is install the table
> >(and, maybe, the motor). No lifting of heavy items is needed (not that
> >the table and motor are light, but in cast iron bandsaws, the upper,
> >cast iron, part is much heavier than the lower stand).
>
> I just assembled my Jet 16" bandsaw.
>
> It came lying down.
> It came with a big dent in the upper door.
> The motor is already attached.
> You have to attach the table
> You have to unbolt the plywood shipping base
> You have to bolt on two cast iron feet about 2 inches tall.
> Its easy (but not real easy) to stand the saw upright yourself and
> tilt it to fasten the feet.
>
> Overall, 6 bolts and its assembled. 2 on the table, 4 on the feet.
>
> dickm
Well my neighbor and I (mostly him) assembed the jet 16' in about an hour,
came on a pallet lying on it's side, styrofoam and box, motor was mounted,
only thing we did was put the feet on, stand it up, and assemble the table
and fence...works like a champ and is sooooooooooooooo quiet, gonna get a
rubber matt to put under it to take out more vibration, it was level and
plumb to boot! and I had free delivery to the inside of my garage! Empire
machinery is where I bought my from. I couldn't be happier!
Tina
Thanks for that post...I plan with a neighbor to get my New Jet 16" bandsaw
assembled this weekend and this info helps
Tina
"Jon Shelley" <[email protected]> wrote in message
news:[email protected]...
> This seems so obvious that I can't imagine others haven't done it, but
while
> researching bandsaws in the google archives, I saw many posts where people
had
> problems putting the frame up on the stand and needing 2-3 people to help.
So
> I thought at least a few people would benefit from this procedure. I just
put
> together my Ridgid bandsaw and was able to do it easily on my own.
>
> Basically, I just left the frame sitting horizontally on it's side in the
box.
> I removed all the other parts, and cut off the side of the box and the
packing
> which would be below the frame if it were standing up. I then assembled
the
> stand and laid it horizontally on the floor next to the bottom of the
frame,
> which was now peaking out of the box. I had to prop the frame up a little
by
> putting some twoby's underneath the remains of the box, then was able to
line
> up the holes in the stand with the bottom of the frame. Then I just
tightened
> the bolts horizontally.
>
> I walked around the saw, tilted it up from the top, and it went right up.
I
> was worried about tilting it like that because I didn't know if two legs
> diagonally would support the frame whlie it was going up, but there really
was
> no problem and it felt sturdy the whole time. Took almost no effort at
all.
>
>
> Jon
On Fri, 19 Aug 2005 00:32:23 GMT, [email protected] (Jon Shelley) wrote:
>This seems so obvious that I can't imagine others haven't done it, but while
>researching bandsaws in the google archives, I saw many posts where people had
>problems putting the frame up on the stand and needing 2-3 people to help. So
>I thought at least a few people would benefit from this procedure. I just put
>together my Ridgid bandsaw and was able to do it easily on my own.
>
>Basically, I just left the frame sitting horizontally on it's side in the box.
>I removed all the other parts, and cut off the side of the box and the packing
>which would be below the frame if it were standing up. I then assembled the
>stand and laid it horizontally on the floor next to the bottom of the frame,
>which was now peaking out of the box. I had to prop the frame up a little by
>putting some twoby's underneath the remains of the box, then was able to line
>up the holes in the stand with the bottom of the frame. Then I just tightened
>the bolts horizontally.
>
>I walked around the saw, tilted it up from the top, and it went right up. I
>was worried about tilting it like that because I didn't know if two legs
>diagonally would support the frame whlie it was going up, but there really was
>no problem and it felt sturdy the whole time. Took almost no effort at all.
>
>
>Jon
I considered doing just that with my Rigid, since the instructions say GET
HELP..*g*
My concern was alignment, but I guess that it could be re-alighned after you
stood the assembled unit up..
I decided to leave the box in the truck during assembly and put the beast
together next to the tail gate... worked pretty good when it was time to put the
top assembly on, since it was just a matter of sliding it over and lifting a few
inches..
NOTE: if you're working alone, use a board or block to support the blade guide
side, so that the side that the bolt is in is level, or have a third hand..
DAMHIK
mac
Please remove splinters before emailing
On 19 Aug 2005 11:17:05 -0700, "Charlie Self" <[email protected]>
wrote:
>
>Tina wrote:
>> Thanks for that post...I plan with a neighbor to get my New Jet 16" bandsaw
>> assembled this weekend and this info helps
>> Tina
>>
>> "Jon Shelley" <[email protected]> wrote in message
>> news:[email protected]...
>> > This seems so obvious that I can't imagine others haven't done it, but
>> while
>> > researching bandsaws in the google archives, I saw many posts where people
>> had
>> > problems putting the frame up on the stand and needing 2-3 people to help.
>> So
>> > I thought at least a few people would benefit from this procedure. I just
>> put
>> > together my Ridgid bandsaw and was able to do it easily on my own.
>> >
>> > Basically, I just left the frame sitting horizontally on it's side in the
>> box.
>> > I removed all the other parts, and cut off the side of the box and the
>> packing
>> > which would be below the frame if it were standing up. I then assembled
>> the
>> > stand and laid it horizontally on the floor next to the bottom of the
>> frame,
>> > which was now peaking out of the box. I had to prop the frame up a little
>> by
>> > putting some twoby's underneath the remains of the box, then was able to
>> line
>> > up the holes in the stand with the bottom of the frame. Then I just
>> tightened
>> > the bolts horizontally.
>> >
>> > I walked around the saw, tilted it up from the top, and it went right up.
>> I
>> > was worried about tilting it like that because I didn't know if two legs
>> > diagonally would support the frame whlie it was going up, but there really
>> was
>> > no problem and it felt sturdy the whole time. Took almost no effort at
>> all.
>> >
>> >
>> > Jon
>
>Actually, this info helps not at all with the Jet 16", which is a
>European pattern unit, not a two part unit with a cast iron top. Your
>Jet will come almost completely assembled, except possible for the
>table and the motor (the motor will probably already be mounted, but
>may not). It will arrive standing up, and if it doesn't, you had better
>talk to the shipper. All you should need to do is install the table
>(and, maybe, the motor). No lifting of heavy items is needed (not that
>the table and motor are light, but in cast iron bandsaws, the upper,
>cast iron, part is much heavier than the lower stand).
I just assembled my Jet 16" bandsaw.
It came lying down.
It came with a big dent in the upper door.
The motor is already attached.
You have to attach the table
You have to unbolt the plywood shipping base
You have to bolt on two cast iron feet about 2 inches tall.
Its easy (but not real easy) to stand the saw upright yourself and
tilt it to fasten the feet.
Overall, 6 bolts and its assembled. 2 on the table, 4 on the feet.
dickm