Folks -
Okay, the router wasn't stout enough to draw the plate down flat, so I put a
couple of threaded inserts in the table and pulled it down flat... I know,
not as clean as I'd like, but I've got some edges to profile tonight.
I got to thinking about chips falling/being sucked into the inverted router
motor and got to thinking. Rather than a shield that just clears the arbor
nuts and keeps debris out, what about a thin piece of plastic (think milk
jug) that pushes onto the shank of the bit, spinning along with it and
throwing debris clear of the motor vents? What gave me the idea was the big
"washers" for lack of a better term, that you would find behind an oil seal
on a crankshaft or pinion shaft... They throw the bulk of the oil away from
the seal and seal lip so that it doesn't have as much to contend with...
If I cut the flexible plastic round and had it centered, I don't see that
balance could be affected. Whatcha all thimk?
John
PS: I will NOT be mounting a wire wheel on the router, in case any of you
smarty-pants type were going to chime in.
"John Moorhead" <[email protected]> wrote in message
> what about a thin piece of plastic (think milk jug) that pushes onto the
> shank of the bit, spinning along with it and throwing debris clear of the
> motor vents? What gave me the idea was the big "washers" for lack of a
> better term, that you would find behind an oil seal on a crankshaft or
> pinion shaft... They throw the bulk of the oil away from the seal and seal
> lip so that it doesn't have as much to contend with...
>
> If I cut the flexible plastic round and had it centered, I don't see that
> balance could be affected. Whatcha all thimk?
Plastic at 22,000 rpm scares me.
Wed, Dec 15, 2004, 11:53pm (EST+5) [email protected]
(John=A0Moorhead) started thinking:
<snip> I got to thinking about chips falling/being sucked into the
inverted router motor and got to thinking. <snip>
Thinking? Danger, danger, danger. LMAO
My router table has an opening of better than an inch across. My
previous router quit, so when I pulled it, I opened it up to check for
sawdust, etc. Totally clean, not even dust. It doesn't suck anything
in, it blows it out. So, I wouldn't worry about it.
JOAT
We cannot direct the wind, but we can adjust the sails.
- unknown
On Thu, 16 Dec 2004 17:06:56 GMT, [email protected] (Lawrence
Wasserman) wrote:
>On the routers that I've looked at, the internal cooling fan is
>designed to exhaust through the opening at the shaft end of the motor,
>in other words, whatever air the tiny fan pulls through is exhausted
>in such a way that it helps blow chips & dust away from the insides of
>the motor. Aside from spinning a piece of plastic at 23000 RPM you
>might also cause the router motor to overheat.
I had a problem with my plenum box collection router table where the
motor would suck chips in the "top" and clog the airflow. I ended up
collecting above the table and directing airflow up through the table
insert.
In article <[email protected]>,
John Moorhead <[email protected]> wrote:
>Folks -
>
>Okay, the router wasn't stout enough to draw the plate down flat, so I put a
>couple of threaded inserts in the table and pulled it down flat... I know,
>not as clean as I'd like, but I've got some edges to profile tonight.
>
>I got to thinking about chips falling/being sucked into the inverted router
>motor and got to thinking. Rather than a shield that just clears the arbor
>nuts and keeps debris out, what about a thin piece of plastic (think milk
>jug) that pushes onto the shank of the bit, spinning along with it and
>throwing debris clear of the motor vents? What gave me the idea was the big
>"washers" for lack of a better term, that you would find behind an oil seal
>on a crankshaft or pinion shaft... They throw the bulk of the oil away from
>the seal and seal lip so that it doesn't have as much to contend with...
>
>If I cut the flexible plastic round and had it centered, I don't see that
>balance could be affected. Whatcha all thimk?
>
>John
>
>PS: I will NOT be mounting a wire wheel on the router, in case any of you
>smarty-pants type were going to chime in.
>
>
On the routers that I've looked at, the internal cooling fan is
designed to exhaust through the opening at the shaft end of the motor,
in other words, whatever air the tiny fan pulls through is exhausted
in such a way that it helps blow chips & dust away from the insides of
the motor. Aside from spinning a piece of plastic at 23000 RPM you
might also cause the router motor to overheat.
--
Larry Wasserman Baltimore, Maryland
[email protected]
On Wed, 15 Dec 2004 23:53:24 GMT, "John Moorhead"
<[email protected]> wrote:
>Folks -
>
>Okay, the router wasn't stout enough to draw the plate down flat, so I put a
>couple of threaded inserts in the table and pulled it down flat... I know,
>not as clean as I'd like, but I've got some edges to profile tonight.
>
>I got to thinking about chips falling/being sucked into the inverted router
>motor and got to thinking. Rather than a shield that just clears the arbor
>nuts and keeps debris out, what about a thin piece of plastic (think milk
>jug) that pushes onto the shank of the bit, spinning along with it and
>throwing debris clear of the motor vents?
that's a lot of RPMs. I don't think it's gonna last long.
>What gave me the idea was the big
>"washers" for lack of a better term, that you would find behind an oil seal
>on a crankshaft or pinion shaft... They throw the bulk of the oil away from
>the seal and seal lip so that it doesn't have as much to contend with...
>
>If I cut the flexible plastic round and had it centered, I don't see that
>balance could be affected. Whatcha all thimk?
>
>John
>
>PS: I will NOT be mounting a wire wheel on the router, in case any of you
>smarty-pants type were going to chime in.
>
I had a problem with chips fouling the vents on my table router. I
solved it nicely by reversing the air flow. I put a fan blowing air
into the cabinet of the router table and set up dust extraction above
the bit.
On Wed, 15 Dec 2004 23:53:24 GMT, "John Moorhead"
<[email protected]> wrote:
>Folks -
>
>Okay, the router wasn't stout enough to draw the plate down flat, so I put a
>couple of threaded inserts in the table and pulled it down flat... I know,
>not as clean as I'd like, but I've got some edges to profile tonight.
>
>I got to thinking about chips falling/being sucked into the inverted router
>motor and got to thinking. Rather than a shield that just clears the arbor
>nuts and keeps debris out, what about a thin piece of plastic (think milk
>jug) that pushes onto the shank of the bit, spinning along with it and
>throwing debris clear of the motor vents? What gave me the idea was the big
>"washers" for lack of a better term, that you would find behind an oil seal
>on a crankshaft or pinion shaft... They throw the bulk of the oil away from
>the seal and seal lip so that it doesn't have as much to contend with...
>
>If I cut the flexible plastic round and had it centered, I don't see that
>balance could be affected. Whatcha all thimk?
>
>John
>
>PS: I will NOT be mounting a wire wheel on the router, in case any of you
>smarty-pants type were going to chime in.
>
John.. don't mount a saw blade on it either.. *g*
Your protector may or may not be a good idea...
if it stops a chip from trashing your router, it's a great thing..
if it comes loose and hits you, or deflects a chip away from the
router and at you, it's not as great..
Bottom line for me is that my ol' craftsman router has been hangin'
upside down for about 12 or 15 years and still runs when I flip the
remote switch...
John,
My routers have a small fan attached to the shaft as probably most other
routers also. The fan causes air to be drawn in from the top of the router
and blown downwards toward the bit. Even with the router inverted, the
airflow is enough on my 3hp model to keep it from being clogged. Really
don't see what purpose your shield would serve.
Bob S.
"John Moorhead" <[email protected]> wrote in message
news:[email protected]...
> Folks -
>
> Okay, the router wasn't stout enough to draw the plate down flat, so I put
a
> couple of threaded inserts in the table and pulled it down flat... I know,
> not as clean as I'd like, but I've got some edges to profile tonight.
>
> I got to thinking about chips falling/being sucked into the inverted
router
> motor and got to thinking. Rather than a shield that just clears the
arbor
> nuts and keeps debris out, what about a thin piece of plastic (think milk
> jug) that pushes onto the shank of the bit, spinning along with it and
> throwing debris clear of the motor vents? What gave me the idea was the
big
> "washers" for lack of a better term, that you would find behind an oil
seal
> on a crankshaft or pinion shaft... They throw the bulk of the oil away
from
> the seal and seal lip so that it doesn't have as much to contend with...
>
> If I cut the flexible plastic round and had it centered, I don't see that
> balance could be affected. Whatcha all thimk?
>
> John
>
> PS: I will NOT be mounting a wire wheel on the router, in case any of you
> smarty-pants type were going to chime in.
>
>
John, you are trying to solve a problem where no exists. Your router
will do fine in a table without jury rigging a shield.
David
John Moorhead wrote:
> Folks -
>
> Okay, the router wasn't stout enough to draw the plate down flat, so I put a
> couple of threaded inserts in the table and pulled it down flat... I know,
> not as clean as I'd like, but I've got some edges to profile tonight.
>
> I got to thinking about chips falling/being sucked into the inverted router
> motor and got to thinking. Rather than a shield that just clears the arbor
> nuts and keeps debris out, what about a thin piece of plastic (think milk
> jug) that pushes onto the shank of the bit, spinning along with it and
> throwing debris clear of the motor vents? What gave me the idea was the big
> "washers" for lack of a better term, that you would find behind an oil seal
> on a crankshaft or pinion shaft... They throw the bulk of the oil away from
> the seal and seal lip so that it doesn't have as much to contend with...
>
> If I cut the flexible plastic round and had it centered, I don't see that
> balance could be affected. Whatcha all thimk?
>
> John
>
> PS: I will NOT be mounting a wire wheel on the router, in case any of you
> smarty-pants type were going to chime in.
>
>
On Thu, 16 Dec 2004 00:28:07 GMT, "BobS" <[email protected]> wrote:
>John,
>
>My routers have a small fan attached to the shaft as probably most other
>routers also. The fan causes air to be drawn in from the top of the router
>and blown downwards toward the bit. Even with the router inverted, the
>airflow is enough on my 3hp model to keep it from being clogged. Really
>don't see what purpose your shield would serve.
>
>Bob S.
>
>
i had a crapsman years ago that was killed by a peice o debris falling
in the fan. what a noise it made! not a total loss though. [ i saved
the cord!!!! ] you are correct however that MOST routers would not let
this happen. the fan was a mangled mess when it finaly stoped grinding
and i got a look at it. sure glad it wasnt body parts! lol
skeez