You're right about galvanized pipe, that's why I don't use it. That is what
is in use on the cover of FWW.
The new Henry Taylor tools are not as good as they once were. I like the
Dastra tools myself.
--
Bill Rittner
R & B ENTERPRISES
[email protected]
"Don't take this life too seriously.......nobody
gets out alive" (Unknown)
Remove "no" to reply
"Mike Hide" <[email protected]> wrote in message
news:dUvmb.11783$9E1.56868@attbi_s52...
> Bill , I find if you do galvanized then it acts as a lubricant and the
> clamp pressure tends to "creep down".
>
> Regarding AI chisels they have been well known in the carving tool area
for
> a very long time, so their stuff must be good .I personally do not have
any
> of their tools , I have about 150 Henry Taylor carving tools which in my
> opinion are very hard to beat, not as pretty as the swiss stuff but very
> functional .....mjh
>
> --
> mike hide
>
>
>
> "Bill Rittner" <[email protected]> wrote in message
> news:h6umb.93837$sp2.85088@lakeread04...
> > It's not as much of a problem when you use galvanized pipe, but, that
type
> > of pipe is not recommended. I use clear packaging tape on the pipes to
> > prevent stains.
> >
> > BTW. Thanks for your input on the AI chisels.
> >
> > --
> > Bill Rittner
> > R & B ENTERPRISES
> >
> > [email protected]
> >
> > "Don't take this life too seriously.......nobody
> > gets out alive" (Unknown)
> >
> > Remove "no" to reply
> > "Mike Hide" <[email protected]> wrote in message
> > news:5fnmb.9916$ao4.23467@attbi_s51...
> > > Now if I did that ,had the clamps laying on the boards without
> separation
> > at
> > > the glue joints ,I would have iron stains all over the place
> > >
> > > --
> > > mike hide
> > >
> > >
> > >
> > >
> >
> >
>
Bill , I find if you do galvanized then it acts as a lubricant and the
clamp pressure tends to "creep down".
Regarding AI chisels they have been well known in the carving tool area for
a very long time, so their stuff must be good .I personally do not have any
of their tools , I have about 150 Henry Taylor carving tools which in my
opinion are very hard to beat, not as pretty as the swiss stuff but very
functional .....mjh
--
mike hide
"Bill Rittner" <[email protected]> wrote in message
news:h6umb.93837$sp2.85088@lakeread04...
> It's not as much of a problem when you use galvanized pipe, but, that type
> of pipe is not recommended. I use clear packaging tape on the pipes to
> prevent stains.
>
> BTW. Thanks for your input on the AI chisels.
>
> --
> Bill Rittner
> R & B ENTERPRISES
>
> [email protected]
>
> "Don't take this life too seriously.......nobody
> gets out alive" (Unknown)
>
> Remove "no" to reply
> "Mike Hide" <[email protected]> wrote in message
> news:5fnmb.9916$ao4.23467@attbi_s51...
> > Now if I did that ,had the clamps laying on the boards without
separation
> at
> > the glue joints ,I would have iron stains all over the place
> >
> > --
> > mike hide
> >
> >
> >
> >
>
>
It's not as much of a problem when you use galvanized pipe, but, that type
of pipe is not recommended. I use clear packaging tape on the pipes to
prevent stains.
BTW. Thanks for your input on the AI chisels.
--
Bill Rittner
R & B ENTERPRISES
[email protected]
"Don't take this life too seriously.......nobody
gets out alive" (Unknown)
Remove "no" to reply
"Mike Hide" <[email protected]> wrote in message
news:5fnmb.9916$ao4.23467@attbi_s51...
> Now if I did that ,had the clamps laying on the boards without separation
at
> the glue joints ,I would have iron stains all over the place
>
> --
> mike hide
>
>
>
>
What abour Sorby? I used to think they were one of the best but ????.
Just asking because I don't have enough money to buy Taylor and
experiment.
On Sat, 25 Oct 2003 19:54:23 -0400, "Bill Rittner" <[email protected]>
wrote:
>You're right about galvanized pipe, that's why I don't use it. That is what
>is in use on the cover of FWW.
>
>The new Henry Taylor tools are not as good as they once were. I like the
>Dastra tools myself.