"Jim Behning" <[email protected]> wrote in message
news:[email protected]...
> On Sat, 18 Aug 2007 15:52:26 GMT, "Joe" <[email protected]> wrote:
>
>>Has anyone created their own vacuum bag setup using a venturi and their
>>air
>>compressor? I'm looking to do the same and would like to learn of
>>anything
>>you learned in the process. Specifically, I'd like to avoid replicating
>>any
>>mistakes! <grin>
>>
>>Joe
>>
> Would the first mistake be an assumption that a $50 vacuum would work
> better, be less expensive to operate and take less time to get
> working? Would you not need a huge air compressor drawing a lot of
> electricity to make a working vacuum?
I *assumed* nothing. I asked for input. Regarding your first question, the
answer is I don't know. Is that the mistake you made? I found no $50
vacuum pumps in my search. Based on your implied knowledge of better, less
expensive and less time, you either have experience and have chosen not to
share it (thanks for nothing) or you have no experience to share and are
making assumptions that you accuse me of making. Either way, welcome to my
killfile. Oh, and regarding your 2nd question, thank you for repeating it
back to me without providing anything in the way of additional information.
plonk,
jc
On Sat, 18 Aug 2007 15:52:26 GMT, "Joe" <[email protected]> wrote:
>Has anyone created their own vacuum bag setup using a venturi and their air
>compressor? I'm looking to do the same and would like to learn of anything
>you learned in the process. Specifically, I'd like to avoid replicating any
>mistakes! <grin>
>
>Joe
>
Would the first mistake be an assumption that a $50 vacuum would work
better, be less expensive to operate and take less time to get
working? Would you not need a huge air compressor drawing a lot of
electricity to make a working vacuum?
"Joe" <[email protected]> wrote in message
news:[email protected]...
> Has anyone created their own vacuum bag setup using a venturi and their
> air compressor? I'm looking to do the same and would like to learn of
> anything you learned in the process. Specifically, I'd like to avoid
> replicating any mistakes! <grin>
>
> Joe
>
>
I have not used this for a "bagging" system but I have used this to vacuum
cast jewelry. I used an old "solder sucker" device used in repairing circuit
boards for removing ICs by sucking the solder from around the IC legs. These
are quite small and can be operated with most compressors. Most are actuated
by a solenoid triggered by a foot switch, I rewired mine with just a manual
switch. You might be able to find one at a surplus electronics store.
--
"shut up and keep diggen"
Jerry
Joe wrote:
| Has anyone created their own vacuum bag setup using a venturi and
| their air compressor? I'm looking to do the same and would like to
| learn of anything you learned in the process. Specifically, I'd
| like to avoid replicating any mistakes! <grin>
I took a different approach and use a recycled refrigerator compressor
as my vacuum pump. It has worked well for me for about five years,
cost nothing, will pull about 25"Hg, and it's _very_ quiet.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
Jerry wrote:
| "Morris Dovey" <[email protected]> wrote in
| news:46c7992e$0$3567$815e3792 @news.qwest.net:
|
|| Joe wrote:
||| Has anyone created their own vacuum bag setup using a venturi and
||| their air compressor? I'm looking to do the same and would like
||| to learn of anything you learned in the process. Specifically,
||| I'd like to avoid replicating any mistakes! <grin>
||
|| I took a different approach and use a recycled refrigerator
|| compressor as my vacuum pump. It has worked well for me for about
|| five years, cost nothing, will pull about 25"Hg, and it's _very_
|| quiet.
|
| Did you have to lubricate the compressor in any way? they're
| normally cooled and lubricated by the freon.
My understanding is that there's quite a bit of oil in the coolant
mix. There was oil in the compressor when I got it, and I haven't
added more.
I haven't worried about ruining the 30-YO compressor because friends
have brought in three more (recycled) compressors that I've held in
reserve.
Murphy's Law says that the current compressor won't fail until I've
managed to give away the replacements... :-)
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
Hi Joe.
A good source of used vacuum pumps is the graphic arts trade (i.e.
supplies for plate making and printing). Every print shop used to have
vacuum frames for holding copy flat and in position. All that traditional
equipment (large cameras, lights, frames (copy and contact), vacuum pumps)
got replaced by scanners. Yellow Pages should help you find a graphic arts
dealer in your area.
I also found some small vacuum pumps in an electronics/surplus store quite
a few years ago that came from dismantled scientific gear.
Hope this help! Regards.
Andypack
"Morris Dovey" <[email protected]> wrote in news:46c7992e$0$3567$815e3792
@news.qwest.net:
> Joe wrote:
>| Has anyone created their own vacuum bag setup using a venturi and
>| their air compressor? I'm looking to do the same and would like to
>| learn of anything you learned in the process. Specifically, I'd
>| like to avoid replicating any mistakes! <grin>
>
> I took a different approach and use a recycled refrigerator compressor
> as my vacuum pump. It has worked well for me for about five years,
> cost nothing, will pull about 25"Hg, and it's _very_ quiet.
>
> --
> Morris Dovey
> DeSoto Solar
> DeSoto, Iowa USA
> http://www.iedu.com/DeSoto/
>
>
>
Did you have to lubricate the compressor in any way? they're normally
cooled and lubricated by the freon.
Joe wrote:
I found no $50 vacuum pumps in my search.
You can try Bill Noble. He often has inexpensive used Gast vacuum pumps
that he offers for sale on "rec.crafts.woodturning".
His web site is:
http://www.wbnoble.com/
--
Jack Novak
Buffalo, NY - USA
[email protected]
On Sat, 18 Aug 2007 15:52:26 GMT, "Joe" <[email protected]> wrote:
>Has anyone created their own vacuum bag setup using a venturi and their air
>compressor?
No, it's too damn noisy and vac bagging is a slow process.
Find a vacuum pump - its not hard. You can even use a "Vac-U-Vin" cheap
plastic handpump. If the bag's well sealed and there's a non-return
valve, you don't need to keep pumping continually.
OK, so I google vacuum bag. I see that they are using a vacuum pump
similar to ones used on medical equipment for air conditioning
service. The one article suggests that just 11 inches might be enough
for their project.
http://www.2linc.com/venturi_vacuum.htm#Vacuum%20Data
My dad did this when serviceing his car's ac.
http://www.dream-models.com/eco/vacuumpump.html
Since I am in your kill file my googe searching was just for my own
education.
On Sat, 18 Aug 2007 20:19:07 GMT, "Joe" <[email protected]> wrote:
>
>"Jim Behning" <[email protected]> wrote in message
>news:[email protected]...
>> On Sat, 18 Aug 2007 15:52:26 GMT, "Joe" <[email protected]> wrote:
>>
>>>Has anyone created their own vacuum bag setup using a venturi and their
>>>air
>>>compressor? I'm looking to do the same and would like to learn of
>>>anything
>>>you learned in the process. Specifically, I'd like to avoid replicating
>>>any
>>>mistakes! <grin>
>>>
>>>Joe
>>>
>> Would the first mistake be an assumption that a $50 vacuum would work
>> better, be less expensive to operate and take less time to get
>> working? Would you not need a huge air compressor drawing a lot of
>> electricity to make a working vacuum?
>
>I *assumed* nothing. I asked for input. Regarding your first question, the
>answer is I don't know. Is that the mistake you made? I found no $50
>vacuum pumps in my search. Based on your implied knowledge of better, less
>expensive and less time, you either have experience and have chosen not to
>share it (thanks for nothing) or you have no experience to share and are
>making assumptions that you accuse me of making. Either way, welcome to my
>killfile. Oh, and regarding your 2nd question, thank you for repeating it
>back to me without providing anything in the way of additional information.
>
>plonk,
>
>jc
>
Great link Jack. Thanks.
jc
"Nova" <[email protected]> wrote in message
news:_zYxi.8893$5y3.6742@trndny07...
> Joe wrote:
>
> I found no $50 vacuum pumps in my search.
>
> You can try Bill Noble. He often has inexpensive used Gast vacuum pumps
> that he offers for sale on "rec.crafts.woodturning".
>
> His web site is:
>
> http://www.wbnoble.com/
>
> --
> Jack Novak
> Buffalo, NY - USA
> [email protected]