I wanted to see how strong AZEC is since I am considering using it to
make some bat racks for the fields where my daughter plays softball.
I'm looking to make something like this, which I've made in the past
using 3/4 plywood:
http://ep.yimg.com/ca/I/everythingbaseball_2109_100108102
I had some cutoffs of 5/4 x 4 AZEC from a storm door project I just
finished, so I did a little experiment.
I used two 3" deck screws to attach the butt end of a 4" long piece to
the face of another piece as shown below.
The |||| is the side of one piece, the ==== is the 4" face of the
other, the ss are the screws that old the 2 pieces together.
<-------5"------->
||||
||||=========
s||sssss====
||||========X
s||sssss====
||||=========
||||
With the T mounted in my vice, I hit it with a 3 pound sledge hammer
to see if I could split the screws out. X marks the spot.
After multiple hits, I managed to bend the screws and the heads pulled
into the back of material about an 1/8". As the screws bent, the
corner of the piece I was hitting dug slightly into the face of the
back piece.
The AZEC never showed any signs of "splitting" nor did it appear that
the threads pulled out of the material at all.
I'm sure that the sledge hammer whacks applied more force than the
girls every will unless they jump up and down on the bat rack.
I'm think these racks ought to last just about forever.
On Jun 14, 4:05=A0pm, "Lew Hodgett" <[email protected]> wrote:
> =A0DerbyDad03 wrote:
>
> re: "Azek" w/ a "k" instead of a "c"
>
> Yeah, I knew that. Brain fart.
>
> And I agree that the flex shouldn't be an issue, especially since I
> will be screwing the edge of one piece to the face of another, in
> shorter than 3' sections.
>
> If I put a screw between each bat receptacle, and maybe even add some
> AZEC ;-) adhesive, the rack should be plenty rigid.
>
> Other opinions are certainly welcome.
> ---------------------------------------
> Would consider cutting a dado, 1/8" deep,in face board and gluing /W/
> TiteBond II.
>
> Installing screws from the back to strengthen "finger" between bats
> would be mandatory IMHO.
>
> Have fun.
>
> Lew
re: "Installing screws from the back to strengthen "finger" between
bats would be mandatory IMHO."
That was always the plan.
The dado is a good idea.
Oh great, more white powder all over the shop!
On Jun 14, 12:12=A0pm, dpb <[email protected]> wrote:
> DerbyDad03 wrote:
> > I wanted to see how strong AZEC is since ...
> ...
> > The AZEC never showed any signs of "splitting" nor did it appear that
> > the threads pulled out of the material at all.
>
> ...
>
> "Azek" w/ a "k" instead of a "c" but that's a minor nit...
>
> It is strong enough and in short sections as you used it won't show up
> but as construction material it is more limber than wood of same
> dimensional thickness and so flexes more. =A0It also tends to relax over =
a
> span w/ time.
>
> Those characteristics won't be of significance in the given application,
> just an observation.
>
> --
re: "Azek" w/ a "k" instead of a "c"
Yeah, I knew that. Brain fart.
And I agree that the flex shouldn't be an issue, especially since I
will be screwing the edge of one piece to the face of another, in
shorter than 3' sections.
If I put a screw between each bat receptacle, and maybe even add some
AZEC ;-) adhesive, the rack should be plenty rigid.
Other opinions are certainly welcome.
DerbyDad03 wrote:
re: "Azek" w/ a "k" instead of a "c"
Yeah, I knew that. Brain fart.
And I agree that the flex shouldn't be an issue, especially since I
will be screwing the edge of one piece to the face of another, in
shorter than 3' sections.
If I put a screw between each bat receptacle, and maybe even add some
AZEC ;-) adhesive, the rack should be plenty rigid.
Other opinions are certainly welcome.
---------------------------------------
Would consider cutting a dado, 1/8" deep,in face board and gluing /W/
TiteBond II.
Installing screws from the back to strengthen "finger" between bats
would be mandatory IMHO.
Have fun.
Lew
DerbyDad03 wrote:
> I wanted to see how strong AZEC is since ...
...
> The AZEC never showed any signs of "splitting" nor did it appear that
> the threads pulled out of the material at all.
...
"Azek" w/ a "k" instead of a "c" but that's a minor nit...
It is strong enough and in short sections as you used it won't show up
but as construction material it is more limber than wood of same
dimensional thickness and so flexes more. It also tends to relax over a
span w/ time.
Those characteristics won't be of significance in the given application,
just an observation.
--