Awarea s I am that Scary Sharp(tmSomebody from the past) is a part of haory
wReck lore, I bought a set of Norton oilstones at the woodworking show this
past weekend. Using them this evening to put an edge on some old,
disreputable, but still usable Craftsman chisels, as well as a bunch of
card scrapers, I was glad I spent the relatively few dollars they cost.
But how do I clean them up? Or should I clean them up? The white Washita
(sp?) wiped clean with just a paper towel, but the coarse and medium stones
didn't come so clean, and naturally had much more swarf.
I've seen, and own, examples of clogged stones. What's the recommendation
for cleaning?
Patriarch
I have soaked them in gas for a couple of days in a closed container,
then swish them around in the gas to get the loose particles off.
Works pretty well on the carborundum variety stones. If that still
doesn't do the trick after soaking, I take a stainless steel brush to
them and scrub them with Comet.
On my soft stones like my Washitas or Arkansas, I use the same method
but change the brush (if needed) to a stiff nylon cleaning brush from
the dollar store. They all clean up great.
Robert
Patriarch wrote:
> But how do I clean them up? Or should I clean them up? The white Washita
> (sp?) wiped clean with just a paper towel, but the coarse and medium stones
> didn't come so clean, and naturally had much more swarf.
>
> I've seen, and own, examples of clogged stones. What's the recommendation
> for cleaning?
>
> Patriarch
They shouldn't need cleaning to often, as OIL is the name of the stone
:) However when they do, soak them in mineral turps as this is a very
thin oil it cleans the stone and leaves a slight residue thus you don't
have to "feed" them so much oil next time they are used. The best way to
store them is in a wooden box made to measure as this protects the stone
and soaks up excess oil. To make the box just get yourself 2 pieces of
timber about an inch wider and longer than the stone and about 1/2 inch
thicker than the 1/2 way point. Lay the stone on the timber, draw around
the outside, drill out the shape with a forstner bit and square up with
a chisel. One piece for the box and the other for the lid. You can then
place the whole box, with the top of, in a vice for use. This was the
way they taught us when I did my apprenticeship and it has worked fine
for me for the last 35 years.
And I still use a stone that is about 30 yrs old.
Have fun
Hope this helps a bit
Kind regards
John
Patriarch wrote:
> Awarea s I am that Scary Sharp(tmSomebody from the past)
snip
Steve LaMantia. DAGS for the original or take a look at
Woodbutcher's website, if he still has that page up. If not, let
me know and I'll repost the original letter/post.
Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.Patinatools.org/
"John B" <""johntoymaker\"@NOT THIShotmail.com"> wrote in message
news:[email protected]...
> Patriarch wrote:
>
>> But how do I clean them up? Or should I clean them up? The white
>> Washita
>> (sp?) wiped clean with just a paper towel, but the coarse and medium
>> stones didn't come so clean, and naturally had much more swarf.
>>
>> I've seen, and own, examples of clogged stones. What's the
>> recommendation for cleaning? Patriarch
>
> They shouldn't need cleaning to often, as OIL is the name of the stone :)
> However when they do, soak them in mineral turps as this is a very thin
> oil it cleans the stone and leaves a slight residue thus you don't have to
> "feed" them so much oil next time they are used. The best way to store
> them is in a wooden box made to measure as this protects the stone and
> soaks up excess oil. To make the box just get yourself 2 pieces of timber
> about an inch wider and longer than the stone and about 1/2 inch thicker
> than the 1/2 way point. Lay the stone on the timber, draw around the
> outside, drill out the shape with a forstner bit and square up with a
> chisel. One piece for the box and the other for the lid. You can then
> place the whole box, with the top of, in a vice for use. This was the way
> they taught us when I did my apprenticeship and it has worked fine for me
> for the last 35 years.
> And I still use a stone that is about 30 yrs old.
> Have fun
> Hope this helps a bit
> Kind regards
> John
I'll add that I use a mix of kerosen and 30wt oil. The homemade box is the
way my grandfather, father have done it, so now that I have the boxes, I
guess I do the same.
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com
On Mon, 18 Apr 2005 22:20:20 -0500, Patriarch
<[email protected]> wrote:
>Awarea s I am that Scary Sharp(tmSomebody from the past) is a part of haory
>wReck lore, I bought a set of Norton oilstones at the woodworking show this
>past weekend. Using them this evening to put an edge on some old,
>disreputable, but still usable Craftsman chisels, as well as a bunch of
>card scrapers, I was glad I spent the relatively few dollars they cost.
I still like my Arkansas stones, myself... That scary sharp method
worked ok, but it just seemed wrong to me after years and years of oil
stones.
>But how do I clean them up? Or should I clean them up? The white Washita
>(sp?) wiped clean with just a paper towel, but the coarse and medium stones
>didn't come so clean, and naturally had much more swarf.
You should definately clean them up. Depending on how ambitious I'm
feeling when I do it, I either use dish soap and a piece of
scotch-brite, or I just spray the suckers with wd-40 and wipe them off
with a rag. It does actually make a lot of difference in the speed of
your sharpening.
Aut inveniam viam aut faciam
John B > wrote:
> Patriarch wrote:
>
>> But how do I clean them up? Or should I clean them up? The white
>> Washita
>> (sp?) wiped clean with just a paper towel, but the coarse and medium
>> stones didn't come so clean, and naturally had much more swarf.
>>
>> I've seen, and own, examples of clogged stones. What's the
>> recommendation for cleaning?
>> Patriarch
>
>
> They shouldn't need cleaning to often, as OIL is the name of the stone
WHOOPS !!!!!!
Either use a machine oil or thin motor oil 50/50 with turps
Use a lot as the more oil the more the metal filings will be washed away
from the stone.
John
On Mon, 18 Apr 2005 22:20:20 -0500, Patriarch wrote:
> I've seen, and own, examples of clogged stones. What's the recommendation
> for cleaning?
I discovered, accidentally, that rubbing compound works well. Lore says to
soak in kerosene and scrub. [I think that lore says to soak in gasoline,
but that's not a) environmentally sound and b) who could afford to? :) ]
--
"Keep your ass behind you"
vladimir a t mad {dot} scientist {dot} com