On Fri, 06 May 2011 17:48:47 +0000, crasher455 wrote:
> Has anyone here used any of the stackable panel clamps available?
> I found these and was wondering if they are a good clamp or are bad
> quality?
>
> www.stackclamp.com
>
>
> -------------------------------------
If you have to pay that much for clamps you would
run out of money long before you ran out of room,
for glue ups.
basilisk
On Fri, 06 May 2011 18:26:00 -0700, Larry Jaques
<[email protected]> wrote:
>(topposting corrected)
>
>On Fri, 6 May 2011 11:35:23 -0700 (PDT), "SonomaProducts.com"
><[email protected]> wrote:
>
>>Haven't seen these specific clamps up close so don't know if they are
>>quality or not. The concept is not new and worls well. There are a few
>>existing versions such as
>>http://www.rrclamp.com/system_stackable.php
>
>Six 24" clamps for only $235 + s/h?
>
>
>>and
>>
>>http://www.leevalley.com/us/wood/page.aspx?p=54186&cat=1,43838
>
>About the same price as above.
>
>
>>I have also made blocks that lay on my Bessy Parallel clamps.
>>
>>If you do lots of clamping it is evn better to get a panel clamp rack
>>like
>>
>>http://www.quickmachinerycompany.com/products/CR/index.html
>
>Oh, oh! They used the "A" word. Anyone using the term "affordable"
>usually means that the price has at least one comma in it.
>
>
>
>>or from JT
>>
>>or go automatic like
>>
>>http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280671486401&ssPageName=STRK:MEWAX:IT
>
>That's just --== SCARY! ==--
>
>I remember someone posting clamp racks from a magazine or their own
>shop in the past few years. What was that? Maybe it was this article
>(which I can no longer access) from FWW: http://goo.gl/JTo1w
>IIRC, it was pairs of pipe clamps on pivots attached to the wall which
>hinged down flat for clamping.
Or maybe it was this one: http://goo.gl/7e8fV
--
I dislike arguments of any kind. They
are always vulgar and often convincing.
-- Oscar Wilde
(topposting corrected)
On Fri, 6 May 2011 11:35:23 -0700 (PDT), "SonomaProducts.com"
<[email protected]> wrote:
>Haven't seen these specific clamps up close so don't know if they are
>quality or not. The concept is not new and worls well. There are a few
>existing versions such as
>http://www.rrclamp.com/system_stackable.php
Six 24" clamps for only $235 + s/h?
>and
>
>http://www.leevalley.com/us/wood/page.aspx?p=54186&cat=1,43838
About the same price as above.
>I have also made blocks that lay on my Bessy Parallel clamps.
>
>If you do lots of clamping it is evn better to get a panel clamp rack
>like
>
>http://www.quickmachinerycompany.com/products/CR/index.html
Oh, oh! They used the "A" word. Anyone using the term "affordable"
usually means that the price has at least one comma in it.
>or from JT
>
>or go automatic like
>
>http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280671486401&ssPageName=STRK:MEWAX:IT
That's just --== SCARY! ==--
I remember someone posting clamp racks from a magazine or their own
shop in the past few years. What was that? Maybe it was this article
(which I can no longer access) from FWW: http://goo.gl/JTo1w
IIRC, it was pairs of pipe clamps on pivots attached to the wall which
hinged down flat for clamping.
--
I dislike arguments of any kind. They
are always vulgar and often convincing.
-- Oscar Wilde
crasher455 wrote the following:
> Has anyone here used any of the stackable panel clamps available?
> I found these and was wondering if they are a good clamp or are bad
> quality?
>
> www.stackclamp.com
>
>
> -------------------------------------
Buy a couple and let us know how they work.
or maybe you already have hundreds of them on hand?
Sorry, I'm always suspicious of first time posting people who bring up a
subject about a particular product with a link.
Perhaps if you had been a regular poster, I wouldn't think it was spam.
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @
Haven't seen these specific clamps up close so don't know if they are
quality or not. The concept is not new and worls well. There are a few
existing versions such as
http://www.rrclamp.com/system_stackable.php
and
http://www.leevalley.com/us/wood/page.aspx?p=3D54186&cat=3D1,43838
I have also made blocks that lay on my Bessy Parallel clamps.
If you do lots of clamping it is evn better to get a panel clamp rack
like
http://www.quickmachinerycompany.com/products/CR/index.html
or from JT
or go automatic like
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3D280671486401&ssPageNam=
e=3DSTRK:MEWAX:IT
On May 6, 10:48=A0am, [email protected]
(crasher455) wrote:
> Has anyone here used any of the stackable panel clamps available?
> I found these and was wondering if they are a good clamp or are bad
> quality?
>
> www.stackclamp.com
>
> -------------------------------------
On 5/6/2011 2:20 PM, basilisk wrote:
> On Fri, 06 May 2011 17:48:47 +0000, crasher455 wrote:
>
>> Has anyone here used any of the stackable panel clamps available?
>> I found these and was wondering if they are a good clamp or are bad
>> quality?
>>
>> www.stackclamp.com
>>
>>
>> -------------------------------------
> If you have to pay that much for clamps you would
> run out of money long before you ran out of room,
> for glue ups.
>
> basilisk
Have to agree with you on that. They sure are proud of their clamps.
Of course, don't need to sell as many to keep the shop open. Think will
just keep piling things on the work bench, floor and dog if he doesn't
move fast enough
Larry Jaques wrote:
>> or go automatic like
>>
>> http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280671486401&ssPageName=STRK:MEWAX:IT
>
> That's just --== SCARY! ==--
>
Wow, you could start your own assembly line! Really cool!
Bill
> I remember someone posting clamp racks from a magazine or their own
> shop in the past few years. What was that? Maybe it was this article
> (which I can no longer access) from FWW: http://goo.gl/JTo1w
> IIRC, it was pairs of pipe clamps on pivots attached to the wall which
> hinged down flat for clamping.
>
> --
> I dislike arguments of any kind. They
> are always vulgar and often convincing.
> -- Oscar Wilde
"willshak" <[email protected]> wrote in message
news:[email protected]...
> crasher455 wrote the following:
>> Has anyone here used any of the stackable panel clamps available?
>> I found these and was wondering if they are a good clamp or are bad
>> quality?
>>
>> www.stackclamp.com
>>
>>
>> -------------------------------------
>
> Buy a couple and let us know how they work.
> or maybe you already have hundreds of them on hand?
>
> Sorry, I'm always suspicious of first time posting people who bring up a
> subject about a particular product with a link.
> Perhaps if you had been a regular poster, I wouldn't think it was spam.
>
Good Catch!
--
"I'm the man who broke the bank at Monte Carlo ..."
On Fri, 6 May 2011 13:20:07 -0500, basilisk <[email protected]>
wrote:
>On Fri, 06 May 2011 17:48:47 +0000, crasher455 wrote:
>
>> Has anyone here used any of the stackable panel clamps available?
>> I found these and was wondering if they are a good clamp or are bad
>> quality?
>>
>> www.stackclamp.com
>>
>>
>> -------------------------------------
>If you have to pay that much for clamps you would
>run out of money long before you ran out of room,
>for glue ups.
Yeah. Who do they think they are, Jorgy? Or Festool?
Then how do you do FIFO unclamping? You're out of luck there, too.
--
I dislike arguments of any kind. They
are always vulgar and often convincing.
-- Oscar Wilde
"Larry Jaques" <[email protected]> wrote in message
> Oh, oh! They used the "A" word. Anyone using the term "affordable"
> usually means that the price has at least one comma in it.
How about something more affordable then?
http://www.leevalley.com/en/wood/page.aspx?p=31181&cat=1,43838,47843&ap=1