In an attempt to broaden by woodworking skills, I bought a PC 690LR router.
. My question is specifically about this router. On the bottom, there is a
black plastic base. I attempted to use a 1/4 roundover bit today, but had
to remove the black plastic base first before I could use the bit. What is
the black plastic base used for?
Thank you for your time and patience.
The black plastic base is to allow the router to slide and not
scratch a wood surface. There is a recessed "pocket" in that
black plastic base plate made to hold porter cable type guide
collars. I can't imagine using the router without the plastic
base. I have an assortment of Lexan base plates with different
shapes and different size center holes for larger router bits.
You can buy extra black plastic base plates.
Do you intend to use the router free hand or mount it upside down
in a table? Most table mount systems would remove the black
plastic and mount the base to a plate of some type.
It is not unusual to need to cut a larger hole in a base plate to
accommodate a larger bit, but I do think you want to keep the base
plate as close to the size of the bit as possible.
--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)
[email protected]
"JohnnyC" <[email protected]> wrote in message
news:[email protected]...
> In an attempt to broaden by woodworking skills, I bought a PC
> 690LR router. . My question is specifically about this router.
> On the bottom, there is a black plastic base. I attempted to
> use a 1/4 roundover bit today, but had to remove the black
> plastic base first before I could use the bit. What is the
> black plastic base used for?
>
> Thank you for your time and patience.
>
>
>
"JohnnyC" <[email protected]> wrote in message
news:[email protected]...
> In an attempt to broaden by woodworking skills, I bought a PC 690LR
router.
> . My question is specifically about this router. On the bottom, there is
a
> black plastic base. I attempted to use a 1/4 roundover bit today, but had
> to remove the black plastic base first before I could use the bit. What
is
> the black plastic base used for?
Why did you have to remove the plastic base?
Was the bit too large to fit through the center hole?
Was the bit not long enough for it to present enough
profile through the base?
I can't imagine a 1/4" roundover bit being too large
to fit though the default hole size of the PC 690.
If the bit seems too short, perhaps the motor is not
seated at the correct depth in the base. Check the
documentation that came with the router.
Would not remove the subbase to install a cutter. There is an easier
way to resolve this cutter hole/subbase issue. See link below:
http://patwarner.com/round_subbase.html
********************************************************************8
On Jan 20, 4:52=A0pm, "JohnnyC" <[email protected]> wrote:
> In an attempt to broaden by woodworking skills, I bought a PC 690LR router=
.
> . =A0My question is specifically about this router. =A0On the bottom, ther=
e is a
> black plastic base. =A0I attempted to use a 1/4 roundover bit today, but h=
ad
> to remove the black plastic base first before I could use the bit. =A0What=
is
> the black plastic base used for?
>
> Thank you for your time and patience.
The Black plastic disk is one of two that comes with the router. If you
look closely, the center whole in the clear base should accommodate a much
larger bit. This is the base you will use mist often. However, when you
want to make dovetails, or something else that requires an additional
collar, the black base is needed. The center hole accepts the collar so the
bit doesn't rub the jig.
"DanG" <[email protected]> wrote in message
news:[email protected]...
> The black plastic base is to allow the router to slide and not scratch a
> wood surface. There is a recessed "pocket" in that black plastic base
> plate made to hold porter cable type guide collars. I can't imagine using
> the router without the plastic base. I have an assortment of Lexan base
> plates with different shapes and different size center holes for larger
> router bits. You can buy extra black plastic base plates.
>
> Do you intend to use the router free hand or mount it upside down in a
> table? Most table mount systems would remove the black plastic and mount
> the base to a plate of some type.
>
> It is not unusual to need to cut a larger hole in a base plate to
> accommodate a larger bit, but I do think you want to keep the base plate
> as close to the size of the bit as possible.
>
> --
> ______________________________
> Keep the whole world singing . . . .
> DanG (remove the sevens)
> [email protected]
>
>
>
> "JohnnyC" <[email protected]> wrote in message
> news:[email protected]...
>> In an attempt to broaden by woodworking skills, I bought a PC 690LR
>> router. . My question is specifically about this router. On the bottom,
>> there is a black plastic base. I attempted to use a 1/4 roundover bit
>> today, but had to remove the black plastic base first before I could use
>> the bit. What is the black plastic base used for?
>>
>> Thank you for your time and patience.
>>
>>
>>
>
>
JohnnyC wrote:
> In an attempt to broaden by woodworking skills, I bought a PC 690LR
> router. . My question is specifically about this router. On the
> bottom, there is a black plastic base. I attempted to use a 1/4
> roundover bit today, but had to remove the black plastic base first
> before I could use the bit. What is the black plastic base used
> for?
>
> Thank you for your time and patience.
In addition to the comments from others, don't push the bit so far
into the collet as to bottom it out. You need bit shank within the
full collet but there is usually a *LOT* of addtional space beyond the
collet and if you push the bit in all the way it will leave very
little cutting space.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Thank you to all who responded. Yes, I was missing the clear base which
would allow the bit enough clearance.
.
Also made my first rookie mistake...doing a bullnose...I am sure you all
know what happened...Thanks again.
"j" <[email protected]> wrote in message
news:TLXkj.15895$LN4.14008@trnddc07...
> The Black plastic disk is one of two that comes with the router. If you
> look closely, the center whole in the clear base should accommodate a much
> larger bit. This is the base you will use mist often. However, when you
> want to make dovetails, or something else that requires an additional
> collar, the black base is needed. The center hole accepts the collar so
> the bit doesn't rub the jig.
>
>
>
> "DanG" <[email protected]> wrote in message
> news:[email protected]...
>> The black plastic base is to allow the router to slide and not scratch a
>> wood surface. There is a recessed "pocket" in that black plastic base
>> plate made to hold porter cable type guide collars. I can't imagine
>> using the router without the plastic base. I have an assortment of Lexan
>> base plates with different shapes and different size center holes for
>> larger router bits. You can buy extra black plastic base plates.
>>
>> Do you intend to use the router free hand or mount it upside down in a
>> table? Most table mount systems would remove the black plastic and mount
>> the base to a plate of some type.
>>
>> It is not unusual to need to cut a larger hole in a base plate to
>> accommodate a larger bit, but I do think you want to keep the base plate
>> as close to the size of the bit as possible.
>>
>> --
>> ______________________________
>> Keep the whole world singing . . . .
>> DanG (remove the sevens)
>> [email protected]
>>
>>
>>
>> "JohnnyC" <[email protected]> wrote in message
>> news:[email protected]...
>>> In an attempt to broaden by woodworking skills, I bought a PC 690LR
>>> router. . My question is specifically about this router. On the bottom,
>>> there is a black plastic base. I attempted to use a 1/4 roundover bit
>>> today, but had to remove the black plastic base first before I could use
>>> the bit. What is the black plastic base used for?
>>>
>>> Thank you for your time and patience.
>>>
>>>
>>>
>>
>>
>
>
"JohnnyC" <[email protected]> wrote in message
news:[email protected]...
> In an attempt to broaden by woodworking skills, I bought a PC 690LR
> router. . My question is specifically about this router. On the bottom,
> there is a black plastic base. I attempted to use a 1/4 roundover bit
> today, but had to remove the black plastic base first before I could use
> the bit. What is the black plastic base used for?
>
> Thank you for your time and patience.
>
>
>
More info needed but typically the black base helps to keep the metal base
of router from scratching your work.
Now if what you are talking about is simply a cover to protect the regular
black plastic base you may want to pitch it.
Or you need to buy bits with longer shanks. Or simply adjust the base
higher up on the router motor.