Rubbing down Waterlox original for slightly less gloss?

On Mon, 19 Dec 2011 11:58:14 -0500, Greg Guarino <[email protected]>
wrote:

>I've got three coats of Waterlox on the oak rails and stiles of my panel
>doors. Between the second and third I sanded a little. After the third I
>used the Rec.Woodworking Patented Brown Paper Massage. Nice! So I'm done
>there.
>
>But the panels themselves (birch ply) were more absorbent I guess. It
>took 5 coats before the finish looked even to me, but now it's a tad
>glossier than I would prefer. Suggestions?

I'd use fine steel wool (like Liberon) with wax. But it might be hard
to match the sheen of the rails and stiles, you probably will find it
easiest to do the entire door.

But you probably want to do this after a full cure of the finish.
Waterlox says that can be 30-90 days.

On Wed, 28 Dec 2011 14:46:26 -0500, Greg Guarino <[email protected]>
wrote:

>On 12/27/2011 2:59 PM, Jim Weisgram wrote:
>> On Mon, 19 Dec 2011 11:58:14 -0500, Greg Guarino<[email protected]>
>> wrote:
>>
>>> I've got three coats of Waterlox on the oak rails and stiles of my panel
>>> doors. Between the second and third I sanded a little. After the third I
>>> used the Rec.Woodworking Patented Brown Paper Massage. Nice! So I'm done
>>> there.
>>>
>>> But the panels themselves (birch ply) were more absorbent I guess. It
>>> took 5 coats before the finish looked even to me, but now it's a tad
>>> glossier than I would prefer. Suggestions?
>>
>> I'd use fine steel wool (like Liberon) with wax. But it might be hard
>> to match the sheen of the rails and stiles, you probably will find it
>> easiest to do the entire door.
>>
>> But you probably want to do this after a full cure of the finish.
>> Waterlox says that can be 30-90 days.
>
>Thanks. How will I know when it is fully cured?

Ask it. ;)


>doesn't matter. I could drill and mount the hinges and even install the
>doors, then revisit the finish in a couple of months. But if there's a
>way to test it, it would be nice to know.

Since you rubbed the finish instead of brushing or spraying, 30 days
inside a home (60+ degrees) should be sufficient. I seldom wait more
than a couple of weeks, less in the hot summertime.

--
[Television is] the triumph of machine over people.
-- Fred Allen

On 12/27/2011 2:59 PM, Jim Weisgram wrote:
> On Mon, 19 Dec 2011 11:58:14 -0500, Greg Guarino<[email protected]>
> wrote:
>
>> I've got three coats of Waterlox on the oak rails and stiles of my panel
>> doors. Between the second and third I sanded a little. After the third I
>> used the Rec.Woodworking Patented Brown Paper Massage. Nice! So I'm done
>> there.
>>
>> But the panels themselves (birch ply) were more absorbent I guess. It
>> took 5 coats before the finish looked even to me, but now it's a tad
>> glossier than I would prefer. Suggestions?
>
> I'd use fine steel wool (like Liberon) with wax. But it might be hard
> to match the sheen of the rails and stiles, you probably will find it
> easiest to do the entire door.
>
> But you probably want to do this after a full cure of the finish.
> Waterlox says that can be 30-90 days.

Thanks. How will I know when it is fully cured? In a sense, I guess it
doesn't matter. I could drill and mount the hinges and even install the
doors, then revisit the finish in a couple of months. But if there's a
way to test it, it would be nice to know.

On 12/28/2011 7:23 PM, Larry Jaques wrote:

> Since you rubbed the finish instead of brushing or spraying, 30 days
> inside a home (60+ degrees) should be sufficient. I seldom wait more
> than a couple of weeks, less in the hot summertime.

I'll have to put a thermometer in my garage. There's a heating pipe that
runs through the ceiling, making it warmer than outside, but cooler
than in the house. Or I could just take the doors into the house proper
for a couple of weeks.