What do you guys use to get over-spray off Plastic Reading Glasses?
Concerned if I use something to powerful it could melt the plastic or
distort it.
thanks
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.co.nr/
"skeez" <[email protected]> wrote in message
news:[email protected]...
> On Sun, 12 Oct 2008 13:54:56 -0700, evodawg <[email protected]>
> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>>
>>thanks
>
>
> just so happens I had this issue today! layed my glasses [plastic
> lenses] on the bench and sprayed some rattle can poly. OOPS!!!!. I am
> near sighted and dont need them to do up close work. I used laquer
> thinner on a paper shop towel. It cleaned em right up but left streaks
> so Ishot some windex on em and they're good as new. DONT USE
> ACETONE!!!! DAMHIKT...... :-]
>
> skeez
Laquer thinner will also take off the finish on the frames...
Jack
evodawg <[email protected]> wrote in news:gcto72$fl4$1
@registered.motzarella.org:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
Do you know what kind of plastic your lenses are? With that information,
you can do some research into what thinners/cleaners will work without
messing up your glasses. I'd probably try low odor mineral spirits myself.
If nothing else, visit a crafts or hobby shop and ask for something
specificially for removing paint from plastic. Modelers have used brake
fluid, but it softens some plastics.
Puckdropper
--
If you're quiet, your teeth never touch your ankles.
To email me directly, send a message to puckdropper (at) fastmail.fm
evodawg wrote:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
>
> "You can lead them to LINUX
> but you can't make them THINK"
> Running Mandriva release 2008.0 free-i586 using KDE on i586
> Website Address http://rentmyhusband.co.nr/
rm -f --nomelt --nodistort overspray
(Sorry - the devil made me do it.)
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
"skeez" wrote:
> I used to use glass lenses but as my eyes worstened they became too
> heavy and uncomfortable to have resting on the ol shnozzola. its too
> bad too because I liked em better!
Understand.
I wear the "RayBan" aviator glasses which require a 62mm blank.
They are a little heavy, but after almost 40 years, they grow on
you<grin>.
Lew
"skeez" <[email protected]> wrote in message
news:[email protected]...
> On Sun, 12 Oct 2008 13:54:56 -0700, evodawg <[email protected]>
> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>>
>>thanks
>
>
> just so happens I had this issue today! layed my glasses [plastic
> lenses] on the bench and sprayed some rattle can poly. OOPS!!!!. I am
> near sighted and dont need them to do up close work. I used laquer
> thinner on a paper shop towel. It cleaned em right up but left streaks
> so Ishot some windex on em and they're good as new. DONT USE
> ACETONE!!!! DAMHIKT...... :-]
>
I generally use paint thinner, rather than lacquer thinner on my glasses.
If you have any coatings on your glasses, the coating will likely not
respond well to applications of lacquer thinner. Left on long enough and
lacquer thinner can fog plastics too.
--
-Mike-
[email protected]
On Oct 12, 4:54=A0pm, evodawg <[email protected]> wrote:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
> --
> "You can lead them to LINUX
> but you can't make them THINK"
> Running Mandriva release 2008.0 free-i586 using KDE on i586
> Website Addresshttp://rentmyhusband.co.nr/
Belt sander. 36 grit.
It doesn't matter which brand of belt sander...in all cases, the
overspray will be gone... but so will your glasses.
evodawg wrote:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
Over-spray of what? Paint? Varnish? I'd had good luck with liquid hand
soap, warm water and fingertips which is all I use to clean plastic lenses
anyway, I never clean them dry. A wet thumbnail seems to peel off paint,
but perhaps some other finishes would be more difficult to remove if there
is an ingredient that has reacted with the plastic.
<[email protected]> wrote:
>What do you guys use to get over-spray off Plastic Reading Glasses?
>Concerned if I use something to powerful it could melt the plastic or
>distort it.
Basic reason I refuse to have plastic lens.
An Xacto knife does a great job of scraping glass lens clean.
Lew
If you have perscrition lenses, contact the company you got them from
and ask them! All "plastic" lenses are not created equal. or are the
optional coatings that can be applied. Those protective coatings are
continually getting better at everything.
A couple of years ago I got some pretty bad solvent on my one or two
year old glasses and it left the lenses hazy in several areas. It was
a mixture of things including toluene, ketone, etc, etc. The company I
get my glasses from said that shouldn't have been a problem and replaced
the $400 lenses for free!
I have no idea how $10 drug store lenses might respond. I wish
that's all I needed. I'd buy a new pair once a month.
Several years ago the was a TV commercial that offered a simple to apply
coating for damaged lenses; you know the old "$19.95" type of deal. I
had some scratched lenses at the time so I tried it. It worked pretty
well, but I did something else to the lenses that caused the coating
itself to go bad in a couple of spots and I couldn't clean them up, so I
gave up on the product.
Two or three years LATER I get a call from that coating mfr, asking
how I liked their product and did I want to order more. I told them
how things went to H***. They told me that all I had to do was to use
the pre-coating lense cleaner that came with the kit and that would have
taken the first coating off. Then I could have re-coated.
---Too late now, but it could have worked!
Pete Stanaitis
-----------------------
evodawg wrote:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> <[email protected]> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>
> Basic reason I refuse to have plastic lens.
>
> An Xacto knife does a great job of scraping glass lens clean.
>
> Lew
>
>
I gave up on glass lenses years ago when polycarbonate lenses were shown to
me. Get them with a scratch resistant coating and I believe they are tougher
than glass. I do metal work and weld splatter burns into glass and ruins the
lens, poly the weld splatter sticks, but is removed easily with no apparent
damage. Also the poly lenses are tough! I took a hit in the lens years ago
when a tool broke and pieces flew and hit the glass lens and broke it into a
million sharp, jagged pieces. To break the poly lens I would have to take a
shot to the head that would probably kill me before the lens would break. I
have "tested" old poly lenses with a hammer and they are darned near
impossible to break.
I also have wiped the lenses off with lacquer thinner to clean them.
Greg
On Sun, 12 Oct 2008 13:54:56 -0700, evodawg <[email protected]>
wrote:
>What do you guys use to get over-spray off Plastic Reading Glasses?
>Concerned if I use something to powerful it could melt the plastic or
>distort it.
>
>thanks
just so happens I had this issue today! layed my glasses [plastic
lenses] on the bench and sprayed some rattle can poly. OOPS!!!!. I am
near sighted and dont need them to do up close work. I used laquer
thinner on a paper shop towel. It cleaned em right up but left streaks
so Ishot some windex on em and they're good as new. DONT USE
ACETONE!!!! DAMHIKT...... :-]
skeez
On Sun, 12 Oct 2008 13:54:56 -0700, evodawg <[email protected]>
wrote:
>What do you guys use to get over-spray off Plastic Reading Glasses?
>Concerned if I use something to powerful it could melt the plastic or
>distort it.
>
>thanks
I avoid getting the overspray in the first place by taking off my
glasses. I'd replace reading glasses (about $3) if I got paint on
them. Glass prescription glasses are best.
evodawg wrote:
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic
> or
> distort it.
Overspray of _what_? Latex will generally come off in regular
cleaning although it may take a few repetitions. Other kinds of paint
may not.
--
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
Lew Hodgett wrote:
> <[email protected]> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>
> Basic reason I refuse to have plastic lens.
>
> An Xacto knife does a great job of scraping glass lens clean.
>
> Lew
yes but glass is heavy on the nose!!!
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.co.nr/
skeez wrote:
> On Sun, 12 Oct 2008 13:54:56 -0700, evodawg <[email protected]>
> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>>
>>thanks
>
>
> just so happens I had this issue today! layed my glasses [plastic
> lenses] on the bench and sprayed some rattle can poly. OOPS!!!!. I am
> near sighted and dont need them to do up close work. I used laquer
> thinner on a paper shop towel. It cleaned em right up but left streaks
> so Ishot some windex on em and they're good as new. DONT USE
> ACETONE!!!! DAMHIKT...... :-]
>
> skeez
Ok I'll try that. wasn't sure if thinner would cause problems on the
plastic...
Btw it was an oil base.
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.co.nr/
Puckdropper <puckdropper(at)yahoo(dot)com> wrote:
> evodawg <[email protected]> wrote in news:gcto72$fl4$1
> @registered.motzarella.org:
>
>> What do you guys use to get over-spray off Plastic Reading Glasses?
>> Concerned if I use something to powerful it could melt the plastic or
>> distort it.
>>
>> thanks
>
> Do you know what kind of plastic your lenses are? With that information,
> you can do some research into what thinners/cleaners will work without
> messing up your glasses. I'd probably try low odor mineral spirits
> myself.
>
> If nothing else, visit a crafts or hobby shop and ask for something
> specificially for removing paint from plastic. Modelers have used brake
> fluid, but it softens some plastics.
>
> Puckdropper
Have no clue.. I know brake fluid does a number on a cars finish!
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.co.nr/
Morris Dovey wrote:
> evodawg wrote:
>> What do you guys use to get over-spray off Plastic Reading Glasses?
>> Concerned if I use something to powerful it could melt the plastic or
>> distort it.
>>
>> thanks
> >
> > "You can lead them to LINUX
> > but you can't make them THINK"
> > Running Mandriva release 2008.0 free-i586 using KDE on i586
> > Website Address http://rentmyhusband.co.nr/
>
> rm -f --nomelt --nodistort overspray
>
> (Sorry - the devil made me do it.)
>
oh yeah a COMMAND LINE solution... Why didnt I think of that??
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.co.nr/
In article <[email protected]>,
"DGDevin" <[email protected]> wrote:
> evodawg wrote:
>
> > What do you guys use to get over-spray off Plastic Reading Glasses?
> > Concerned if I use something to powerful it could melt the plastic or
> > distort it.
> >
> > thanks
>
> Over-spray of what? Paint? Varnish? I'd had good luck with liquid hand
> soap, warm water and fingertips which is all I use to clean plastic lenses
> anyway, I never clean them dry. A wet thumbnail seems to peel off paint,
> but perhaps some other finishes would be more difficult to remove if there
> is an ingredient that has reacted with the plastic.
I get my reading glasses for $2.99. Just wipe them off with a homemade
tack cloth... ;-)
--
"Keep your ass behind you."
On Mon, 13 Oct 2008 00:09:10 GMT, "Lew Hodgett"
<[email protected]> wrote:
><[email protected]> wrote:
>
>>What do you guys use to get over-spray off Plastic Reading Glasses?
>>Concerned if I use something to powerful it could melt the plastic or
>>distort it.
>
>Basic reason I refuse to have plastic lens.
>
>An Xacto knife does a great job of scraping glass lens clean.
>
>Lew
>
I used to use glass lenses but as my eyes worstened they became too
heavy and uncomfortable to have resting on the ol shnozzola. its too
bad too because I liked em better! :-]
"evodawg" <[email protected]> wrote in message
news:[email protected]...
> What do you guys use to get over-spray off Plastic Reading Glasses?
> Concerned if I use something to powerful it could melt the plastic or
> distort it.
>
> thanks
I used to use waterless hand cleaner back when I used to forget to take
off my glasses <G>
Max