I need to propel a 6 inch wheel at about 5 mph. So I need a cordless
drill or any light cordless tool that is geared to about 400 rpm.
Unfortunately, the thing cannot include a device that causes lockup
when the trigger is released and forward pressure appears on the
drill shaft.
I'd like medium to high quality, but functionally like my cheap
cordless Skil drill, with a clutch that works in both directions.
But my Skil isn't powerful enough and doesn't include a low gear
that tops out at 400 rpm or less.
Hopefully I can disable the braking feature on my DeWalt DC728 14.4
V drill. I disassembled it and got to mess with lots of gears but
did not see the braking mechanism. I guess the braking mechanism is
located in the one of the clutch pieces. It doesn't seem very
modular, I'm not sure I could even use the geared motor without the
clutch.
By the way.
Apparently DeWalt drills use MOLYKOTE grease. I see McMaster has
several different types. What type of that grease or what other type
of grease is suitable for drill gears?
Is handling that grease hazardous?
Thanks.
"Den" <[email protected]> wrote:
> "John Doe" <[email protected]> wrote in message
<please see my original post>
> The braking may be electrical. Shorting the motor terminals
> together when the power is disconnected will brake the
> rotor/armature. This seems to be what is done in my Bosch & Ryobi
> drills. My guess is that it is done in the trigger switch.
The braking on my DeWalt DC728 must be more than electrical. Try
putting a 3-5 pound weight with significant centrifugal force in the
chuck, get it up to speed, and then release the trigger gently as
possible. When I do that here, it binds and serious grating/grinding
happens. After finally getting around to testing the thing, I find a
drill with such a braking device is a complete nonstarter for my
project. Uhg.
> Even with the motor unbraked you will probably get significant
> friction/intertia as you will be driving the rotor (stepped up)
> back through the gearbox. HTH.
Yeah, I think that's what happens with my cheap Skil drill, but the
clutch works in both directions which relieves some of that braking
force.
> What are you tring to do? There are some reasonably priced geared
> DC motors around and reversing is not a problem.
I'm ready to click on any links. DC motors with about the same
amount of power as a 14.4 V or greater cordless drill, and low
geared to about 400 rpm or less.
Cordless drills/tools come in a nice neat package with a trigger
switch and a battery holder, for a reasonable price.
Thanks.
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/
"John Doe" <[email protected]> wrote in message
news:[email protected]...
>
> I need to propel a 6 inch wheel at about 5 mph. So I need a cordless
> drill or any light cordless tool that is geared to about 400 rpm.
> Unfortunately, the thing cannot include a device that causes lockup
> when the trigger is released and forward pressure appears on the
> drill shaft.
>
> I'd like medium to high quality, but functionally like my cheap
> cordless Skil drill, with a clutch that works in both directions.
> But my Skil isn't powerful enough and doesn't include a low gear
> that tops out at 400 rpm or less.
>
> Hopefully I can disable the braking feature on my DeWalt DC728 14.4
> V drill. I disassembled it and got to mess with lots of gears but
> did not see the braking mechanism. I guess the braking mechanism is
> located in the one of the clutch pieces. It doesn't seem very
> modular, I'm not sure I could even use the geared motor without the
> clutch.
>
> By the way.
>
> Apparently DeWalt drills use MOLYKOTE grease. I see McMaster has
> several different types. What type of that grease or what other type
> of grease is suitable for drill gears?
>
> Is handling that grease hazardous?
>
> Thanks.
The braking may be electrical. Shorting the motor terminals together when
the power is disconnected will brake the rotor/armature. This seems to be
what is done in my Bosch & Ryobi drills. My guess is that it is done in the
trigger switch.
Even with the motor unbraked you will probably get significant
friction/intertia as you will be driving the rotor (stepped up) back through
the gearbox. HTH.
What are you tring to do? There are some reasonably priced geared DC motors
around and reversing is not a problem.
>
>> What are you tring to do? There are some reasonably priced geared
>> DC motors around and reversing is not a problem.
>
> I'm ready to click on any links. DC motors with about the same
> amount of power as a 14.4 V or greater cordless drill, and low
> geared to about 400 rpm or less.
>
For a one off job verge shop a large office photocopier, most of the ones
I've stripped have had a great 12/24V gear motor in them. Alternately
someone like: http://www.oatleyelectronics.com/ but on your side of the
world could probably help.
For an ongoing source googling for local suppliers may be the solution.
> Cordless drills/tools come in a nice neat package with a trigger
> switch and a battery holder, for a reasonable price.
>
> Thanks.
>
>
Yep, I use a couple of old cordless drills in rigs for repetitive tapping -
they work a treat and are cheap.
>
> --
> The first big front wheel rollerblades.
> http://www.flickr.com/photos/27532210@N04/2565924423/
In article <[email protected]>,
John Doe <[email protected]> wrote:
> I'm ready to click on any links. DC motors with about the same
> amount of power as a 14.4 V or greater cordless drill, and low
> geared to about 400 rpm or less.
How about a motor from a scrap electric wheelchair or something similar?
--
Stuart Winsor
For Barn dances and folk evenings in the Coventry and Warwickshire area
See: http://www.barndance.org.uk
"Grumpy" <[email protected]> wrote:
>> "John Doe" <[email protected]> wrote in message
>>> I need to propel a 6 inch wheel at about 5 mph. So I need a
>>> cordless drill or any light cordless tool that is geared to
>>> about 400 rpm. Unfortunately, the thing cannot include a device
>>> that causes lockup when the trigger is released and forward
>>> pressure appears on the drill shaft.
> Why not purchase an over-running clutch bearing. They are
> identical dimensions to a standard bell bearing, but transmit
> torque in one direction only. In the other direction they are a
> free running bearing. They are usually about 50% more expensive
> than an equivalent bearing. They are readily available here in
> Australia, so you should have no trouble locating one at any
> reasonably good bearing supplier such as SKF or NSK
I've spent money on that route before. Difficult to match attributes
include environmental contamination, locking torque, and inner\outer
diameter. I'd love to use clutch bearings, but so far no go. I might
try again.
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/
"[email protected]" <[email protected]> wrote:
> I have 14 new in the box Torrington RC-061008 roller clutches.
> They are ID 0.3750, OD 0.6250 and length of 0.500. The current
> price I found was $4.96 each. I would sell them for $2.00 each
> plus shipping.
Do they function under a radial load? Can they be used in a
dirty/dusty environment? Uhg. Too bad I don't have engineering
experience in everything I want to make.
FWIW.
This is not a prototype for a production, it's probably just for me.
I'm looking at cordless drills with a two-piece chuck (as opposed to
the ordinarily much more desirable single sleeve ratcheting type).
Apparently the crummy two-piece chucks do not include a locking
mechanism on the shaft. I ordered a Skil 18 V drill without
batteries dirt cheap for $20 total. I'll plan to use some 18 V
lithium-ion batteries if that drill will work. If possible, maybe
even better would be to use a 36 V lithium-ion battery for which I
already have a battery holder and charger, somehow electrically
splitting it into two 18 V halves. Then again, ack, that 36 V
battery requires a special trigger switch with output properties
that will have to match the 18 V Skil motor. And then that trigger
switch probably won't work with the 18 V battery half I envision
making out of the 36 V battery. So I'll have to buy another
lithium-ion cordless drill kit just to get the batteries, the
holder, and the trigger switch for use with the 18 V lithium-ion
batteries (assuming all lithium-ion batteries have more than
positive and negative output leads). So I might settle for NiMH. Or
whatever.
Uhh... I hate to jump into this since I see that the OP is being cagey, and
kinda rude.....
So I won't offer any suggestions other than to say, have any of you who
answered bothered to click on the link he sometimes (I'm sure accidentally)
left on a few of these posts... reproduced here for those that lost the
original posts...
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/
---
He's built a RollerBlade with a big friggen wheel in the front...
Doesn't take a rocket scientist to figure out that since he wants "5MPH",
"cordless" and "free wheeling" he's trying to stick a motor on it... and
obviously dosen't want to tell us 'cause we'd steal his idea.... you know
what a bunch of low lifes we are... :-)
Umm.. OOOKKKK....
--.- Dave (who prefers to stab the throttle on the O-470, hit 70MPH and
take off)
"John Doe" <[email protected]> wrote in message
news:[email protected]...
>
> I need to propel a 6 inch wheel at about 5 mph. So I need a cordless
> drill or any light cordless tool that is geared to about 400 rpm.
> Unfortunately, the thing cannot include a device that causes lockup
> when the trigger is released and forward pressure appears on the
> drill shaft.
>
> I'd like medium to high quality, but functionally like my cheap
> cordless Skil drill, with a clutch that works in both directions.
> But my Skil isn't powerful enough and doesn't include a low gear
> that tops out at 400 rpm or less.
>
> Hopefully I can disable the braking feature on my DeWalt DC728 14.4
> V drill. I disassembled it and got to mess with lots of gears but
> did not see the braking mechanism. I guess the braking mechanism is
> located in the one of the clutch pieces. It doesn't seem very
> modular, I'm not sure I could even use the geared motor without the
> clutch.
>
> By the way.
>
> Apparently DeWalt drills use MOLYKOTE grease. I see McMaster has
> several different types. What type of that grease or what other type
> of grease is suitable for drill gears?
>
> Is handling that grease hazardous?
>
> Thanks.
"Dave August" <[email protected]> wrote:
> Uhh... I hate to jump into this since I see that the OP is being
> cagey, and kinda rude.....
Awww... poor baby Dave.
> So I won't offer any suggestions
What about your imaginary kill file friend, Dave?
> other than to say, have any of you who answered bothered to click
> on the link he sometimes (I'm sure accidentally)
Another good troll, Dave.
> Doesn't take a rocket scientist to figure out that since he wants
> "5MPH", "cordless" and "free wheeling" he's trying to stick a
> motor on it...
BZZZZT!!!
That's not the project, Dave.
> and obviously dosen't want to tell us 'cause we'd steal his
> idea....
Another wrong conclusion Dave. I've been designing and building
things long enough to have learned some patience. If I ever get a
prototype that works, I'll probably put it on my pictures page.
> you know what a bunch of low lifes we are... :-)
Awww... poor baby Dave.
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/
It's in the Cessna 182...
Wife want's me to make it an IO-470... she's tired of carb ice... (though
that bird is pretty good about it)...
Yeah they are a flying HD...man those jugs are big.... ummm not my wifes..
the O-470...LOL....
Didn't realize till I read your e-mail addy yer a Beach Pilot... Had LOTS
of fun in a T-34 and a Barron-55, but sadly I'm not multi rated, needed my
10K hour ex-P3 pilot buddy to put it in HIS log book.. But as they say ..
"PIC can be in any seat in the aircraft as long as he can reach the
controls"...HeHeHe.. ;-)
Keep the blue side up pal :-)
--.- Dave
"B A R R Y" <[email protected]> wrote in message
news:[email protected]...
>
>
> You have an 0-470?
>
> NNNNNNNNNiiiiiiiiiiiiiiccccccccccccccceeeeeeeeeeeee!!!!!!
>
>
> The flying Harley!
"Den" <[email protected]> wrote in message
news:[email protected]...
>
> "John Doe" <[email protected]> wrote in message
> news:[email protected]...
>>
>> I need to propel a 6 inch wheel at about 5 mph. So I need a cordless
>> drill or any light cordless tool that is geared to about 400 rpm.
>> Unfortunately, the thing cannot include a device that causes lockup
>> when the trigger is released and forward pressure appears on the
>> drill shaft.
>>
>> I'd like medium to high quality, but functionally like my cheap
>> cordless Skil drill, with a clutch that works in both directions.
>> But my Skil isn't powerful enough and doesn't include a low gear
>> that tops out at 400 rpm or less.
>>
>> Hopefully I can disable the braking feature on my DeWalt DC728 14.4
>> V drill. I disassembled it and got to mess with lots of gears but
>> did not see the braking mechanism. I guess the braking mechanism is
>> located in the one of the clutch pieces. It doesn't seem very
>> modular, I'm not sure I could even use the geared motor without the
>> clutch.
>>
>> By the way.
>>
>> Apparently DeWalt drills use MOLYKOTE grease. I see McMaster has
>> several different types. What type of that grease or what other type
>> of grease is suitable for drill gears?
>>
>> Is handling that grease hazardous?
>>
>> Thanks.
>
>
> The braking may be electrical. Shorting the motor terminals together when
> the power is disconnected will brake the rotor/armature. This seems to be
> what is done in my Bosch & Ryobi drills. My guess is that it is done in
> the trigger switch.
>
> Even with the motor unbraked you will probably get significant
> friction/intertia as you will be driving the rotor (stepped up) back
> through the gearbox. HTH.
>
>
> What are you tring to do? There are some reasonably priced geared DC
> motors around and reversing is not a problem.
>
>
>
Why not purchase an over-running clutch bearing. They are identical
dimensions to a standard bell bearing, but transmit torque in one direction
only. In the other direction they are a free running bearing. They are
usually about 50% more expensive than an equivalent bearing. They are
readily available here in Australia, so you should have no trouble locating
one at any reasonably good bearing supplier such as SKF or NSK
On Sep 15, 11:20=A0pm, John Doe <[email protected]> wrote:
> "[email protected]" <[email protected]> wrote:
> > I have 14 new in the box Torrington RC-061008 roller clutches.
> > They are ID 0.3750, OD 0.6250 and length of 0.500. The current
> > price I found was $4.96 each. I would sell them for $2.00 each
> > plus shipping.
>
> Do they function under a radial load? Can they be used in a
> dirty/dusty environment? Uhg. Too bad I don't have engineering
> experience in everything I want to make.
No, I don't think any roller clutch will function with a side load.
That would make the rollers want to twist and quickly wear the housing
or the ramps that give the clutch action. And they are not sealed.
They have grease internally, so dust would not be good.
You may need to incorporate both bearings and clutches in your design.
If I may suggest something. Work on engineer parts or sections of your
design. Don't worry right now about power, speed, batteries, etc. Just
get the mechanical part to work. Then begin to apply power. See what
needs to be changed mechanically, then when that works as you want,
step up the power, voltage and what ever you want. Engineering is not
a one step operation it is is working through the problem over and
over until you get it right.
Good luck. Sounds like a fun project.
Paul
>
> FWIW.
> This is not a prototype for a production, it's probably just for me.
> I'm looking at cordless drills with a two-piece chuck (as opposed to
> the ordinarily much more desirable single sleeve ratcheting type).
> Apparently the crummy two-piece chucks do not include a locking
> mechanism on the shaft. I ordered a Skil 18 V drill without
> batteries dirt cheap for $20 total. I'll plan to use some 18 V
> lithium-ion batteries if that drill will work. If possible, maybe
> even better would be to use a 36 V lithium-ion battery for which I
> already have a battery holder and charger, somehow electrically
> splitting it into two 18 V halves. Then again, ack, that 36 V
> battery requires a special trigger switch with output properties
> that will have to match the 18 V Skil motor. And then that trigger
> switch probably won't work with the 18 V battery half I envision
> making out of the 36 V battery. So I'll have to buy another
> lithium-ion cordless drill kit just to get the batteries, the
> holder, and the trigger switch for use with the 18 V lithium-ion
> batteries (assuming all lithium-ion batteries have more than
> positive and negative output leads). So I might settle for NiMH. Or
> whatever.
John Doe wrote:
>
> See the first sentence of my original post, Barry, are you grasping
> for excuses to avoid helping anybody?
Google rec.woodworking especially finishing. Come back when you can
demonstrate how I don't help very often.
"DEN" asked for more details, and you ignored it. You're going to turn
a wheel, we can read that. The actual application might allow others to
provide even more help.
Building a Battlebot for school? <G>
John.
I have 14 new in the box Torrington RC-061008 roller clutches. They
are ID 0.3750, OD 0.6250 and length of 0.500. The current price I
found was $4.96 each. I would sell them for $2.00 each plus shipping.
I own an electronic assembly service. Years ago when we stuffed leaded
components into holes in circuit boards, we had a machine called a
component sequencer. It cut components from reels and put them onto
new reels in a specific order for an inserter machine to insert them.
The sequencer used rotary solenoids to advance and cut one component
at a time from the master reel. One direction of rotation could be
used, but the solenoid had to return to its resting position. The
roller clutches were between the solenoid shaft and the cutting/
advancing mechanism.
We sold the machines, but seemed to have forgotten a box of clutches.
I just found them the other day.
Would these be of any interest to you?
Paul Drahn, President
Jodeco, Inc.
Redmond, Oregon
>
> I've spent money on that route before. Difficult to match attributes
> include environmental contamination, locking torque, and inner\outer
> diameter. I'd love to use clutch bearings, but so far no go. I might
> try again.
>
> --
> The first big front wheel rollerblades.http://www.flickr.com/photos/27532210@N04/2565924423/
On Sep 14, 10:33 pm, John Doe <[email protected]> wrote:
> I need to propel a 6 inch wheel at about 5 mph. So I need a cordless
> drill or any light cordless tool that is geared to about 400 rpm.
Does it really need to be cordless? Because it kind of sounds like
you need a lathe.
John Doe wrote:
> B A R R Y <[email protected]> wrote:
>
>> John Doe wrote:
>>>
>>> See the first sentence of my original post, Barry, are you
>>> grasping for excuses to avoid helping anybody?
>> Google rec.woodworking especially finishing. Come back when you
>> can demonstrate how I don't help very often.
>
> I don't really know or care, Barry. Why do you assume others are
> asking about schoolwork? Why does it matter to you, Barry?
>
>> "DEN" asked for more details, and you ignored it.
>
> Even if I did ignore it, who's problem is that, Barry?
>
>> You're going to turn a wheel, we can read that.
>
> Did you read that, Barry?
>
>> The actual application might allow others to provide even more
>> help.
>
> Are you dissatisfied with the amount of help I've been given, Barry?
>
>
>
In article <[email protected]>,
John Doe <[email protected]> wrote:
> "Den" <[email protected]> wrote:
(snippage....)
> > Even with the motor unbraked you will probably get significant
> > friction/intertia as you will be driving the rotor (stepped up)
> > back through the gearbox. HTH.
>
> Yeah, I think that's what happens with my cheap Skil drill, but the
> clutch works in both directions which relieves some of that braking
> force.
>
> > What are you tring to do? There are some reasonably priced geared
> > DC motors around and reversing is not a problem.
>
> I'm ready to click on any links. DC motors with about the same
> amount of power as a 14.4 V or greater cordless drill, and low
> geared to about 400 rpm or less.
You might try poking around http://www.surpluscenter.com/ to see if they
have anything that may be suitable. While I don't have extensive
experience with them, I have made small orders once or twice and have
absolutely no complaints at all.
--
Andrew Erickson
"He is no fool who gives what he cannot keep to gain that which he cannot
lose." -- Jim Elliot
Stuart wrote:
> In article <[email protected]>,
> John Doe <[email protected]> wrote:
>
>>I'm ready to click on any links. DC motors with about the same
>>amount of power as a 14.4 V or greater cordless drill, and low
>>geared to about 400 rpm or less.
>
>
> How about a motor from a scrap electric wheelchair or something similar?
>
http://www.surpluscenter.com/item.asp?UID=2008091913482604&item=5-1649&catname=
--Winston
[email protected] wrote:
>
> You may need to incorporate both bearings and clutches in your design.
That's exactly what I was going to suggest. Bearings to control loads
and clutches to drive
>
> Good luck. Sounds like a fun project.
Since the project was never identified, it sounds like school is in
session. <G>
B A R R Y <[email protected]> wrote:
> John Doe wrote:
>>
>> See the first sentence of my original post, Barry, are you
>> grasping for excuses to avoid helping anybody?
>
> Google rec.woodworking especially finishing. Come back when you
> can demonstrate how I don't help very often.
I don't really know or care, Barry. Why do you assume others are
asking about schoolwork? Why does it matter to you, Barry?
> "DEN" asked for more details, and you ignored it.
Even if I did ignore it, who's problem is that, Barry?
> You're going to turn a wheel, we can read that.
Did you read that, Barry?
> The actual application might allow others to provide even more
> help.
Are you dissatisfied with the amount of help I've been given, Barry?
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/
B A R R Y <[email protected]> wrote:
> [email protected] wrote:
>>
>> You may need to incorporate both bearings and clutches in your
>> design.
>
> That's exactly what I was going to suggest.
Anything is possible, Barry.
>> Good luck. Sounds like a fun project.
>
>
> Since the project was never identified, it sounds like school is
> in session. <G>
See the first sentence of my original post, Barry, are you grasping
for excuses to avoid helping anybody?
--
The first big front wheel rollerblades.
http://www.flickr.com/photos/27532210@N04/2565924423/