"HeyBub" <[email protected]> wrote in message
news:[email protected]...
> Of the technique for boring equally-spaced holes in boards that will be
> the sides of a bookshelf, for the little posts that hold up the shelves.
>
> I'll be using a drill press.
>
Simplest, fastest, cheapest method is to just use some pegboard. Cut it to
size, clamp it to the board and drill away. Just make sure that the
distance from the edge is the same front and back.
Most folks I know who do this use some kind of router template. These are
available from almost any kind of woodworkers store.
I have just laid out the holes on the board and marked them. I use
something to "counterpunch" a depression or drill a tiny hole first. This
helps "grab" the drill when lining up the stock under the drill in a drill
press.
I suppose it just depends on how many holes you have to drill and how much
time and money you want to put into it. I have seen custom drill templates
made out of aluminum for this purpose. Just remember any kind of template
can get sloppy real fast if the drill takes any material away from the guide
hole. Which is why most folks prefer a router for this kind of thing.
"Lew Hodgett" <[email protected]> wrote:
> "Lee Michaels" wrote:
>
>> Simplest, fastest, cheapest method is to just use some pegboard.
> -----------------------------------
> Life is too short to waste it.
>
> http://tinyurl.com/7rde2kt
>
> Best $25 you will ever invest.
+10
--
www.ewoodshop.com
On 02 Dec 2011 01:56:02 GMT, Han <[email protected]> wrote:
>"Lew Hodgett" <[email protected]> wrote in news:4ed81b81$0$8602
>[email protected]:
>
>> "Lee Michaels" wrote:
>>
>>> Simplest, fastest, cheapest method is to just use some pegboard.
>> -----------------------------------
>> Life is too short to waste it.
>>
>> http://tinyurl.com/7rde2kt
>>
>> Best $25 you will ever invest.
>>
>> Lew
>
>Indeed. Clamp the jig securely or else ... DAMHIKT
Drill one hole, peg it, move to the other end, drill and peg, then
finish the pattern.
--
Intuition isn't the enemy, but the ally, of reason.
-- John Kord Lagemann
On 02 Dec 2011 01:56:02 GMT, Han <[email protected]> wrote:
>Indeed. Clamp the jig securely or else ... DAMHIKT
We drilled a small hole at each end for a 4d nail to hold it in place.
Mike
On Dec 1, 2:43=A0pm, "HeyBub" <[email protected]> wrote:
> Of the technique for boring equally-spaced holes in boards that will be t=
he
> sides of a bookshelf, for the little posts that hold up the shelves.
>
> I'll be using a drill press.
>
> Thanks.
They sell templates that are made to work with self centering drills,
a drill bit in a sliding spring loaded cylinder. It has a built in
depth stop. Wit the template you can do this with a hand drill pretty
fast.
Lee Michaels wrote:
> "HeyBub" <[email protected]> wrote in message
> news:[email protected]...
>> Of the technique for boring equally-spaced holes in boards that will
>> be the sides of a bookshelf, for the little posts that hold up the
>> shelves. I'll be using a drill press.
>>
> Simplest, fastest, cheapest method is to just use some pegboard. Cut
> it to size, clamp it to the board and drill away. Just make sure
> that the distance from the edge is the same front and back.
[Slaps forehead] Pegboard. Of course. Thanks for reminding me.
"Lew Hodgett" <[email protected]> wrote in news:4ed81b81$0$8602
[email protected]:
> "Lee Michaels" wrote:
>
>> Simplest, fastest, cheapest method is to just use some pegboard.
> -----------------------------------
> Life is too short to waste it.
>
> http://tinyurl.com/7rde2kt
>
> Best $25 you will ever invest.
>
> Lew
Indeed. Clamp the jig securely or else ... DAMHIKT
--
Best regards
Han
email address is invalid
On 12/1/2011 7:56 PM, Han wrote:
> "Lew Hodgett"<[email protected]> wrote in news:4ed81b81$0$8602
> [email protected]:
>
>> "Lee Michaels" wrote:
>>
>>> Simplest, fastest, cheapest method is to just use some pegboard.
>> -----------------------------------
>> Life is too short to waste it.
>>
>> http://tinyurl.com/7rde2kt
>>
>> Best $25 you will ever invest.
>>
>> Lew
>
> Indeed. Clamp the jig securely or else ... DAMHIKT
>
I never have clamped my jig, I use a a shelf hook in a previously
drilled hole to hold it in place.
On 12/1/2011 4:43 PM, HeyBub wrote:
> Of the technique for boring equally-spaced holes in boards that will be the
> sides of a bookshelf, for the little posts that hold up the shelves.
>
> I'll be using a drill press.
>
> Thanks.
>
>
Can you say Tee Dee Us? Unless you just need some DP time, avoid it.
Too darn slow and you don't need "PERFECT" 90 degree holes. Spacing is
important. I use what Lew is suggesting but you can get away with a
brad point bit, depth stop collar, and pegboard.
On 12/1/11 6:27 PM, Lew Hodgett wrote:
> "Lee Michaels" wrote:
>
>> Simplest, fastest, cheapest method is to just use some pegboard.
> -----------------------------------
> Life is too short to waste it.
>
> http://tinyurl.com/7rde2kt
>
> Best $25 you will ever invest.
>
> Lew
>
Someday they will make those bits so they don't clog every 4th hole. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
SonomaProducts.com wrote:
> On Dec 1, 2:43 pm, "HeyBub"<[email protected]> wrote:
>> Of the technique for boring equally-spaced holes in boards that will be the
>> sides of a bookshelf, for the little posts that hold up the shelves.
>>
>> I'll be using a drill press.
>>
>> Thanks.
>
> They sell templates that are made to work with self centering drills,
> a drill bit in a sliding spring loaded cylinder. It has a built in
> depth stop. Wit the template you can do this with a hand drill pretty
> fast.
On a sort-of similar project, I made my own template out of 3/4" scrap
stuff. I clamped it to the work and drilled through the same-size holes
I drilled in it. If your "template" has a square end, it seems like it
would work pretty well for drilling holes in a row along evenly spaced
lines. It will help avoid tear-out too.
Bill
In article <[email protected]>,
HeyBub <[email protected]> wrote:
>Of the technique for boring equally-spaced holes in boards that will be the
>sides of a bookshelf, for the little posts that hold up the shelves.
Here's what I did: I made a wooden strip about three feet long, and
very carefully pounded nails through it at precise 1.5" intervals
so that just their tips stuck out the other side.
Then, whenever I want to make a line of holes, I place the wooden
strip where I want the holes to be, and press it down until all the
nail tips leave good dimples in my workpiece. Then I use the
drill press to drill out all the holes.
A couple more tips: Don't drill the holes all the way through; it's
unsightly. If the bookshelf has more than one vertical compartment,
the vertical board between compartments becomes a problem -- holes
drilled on one side will likely meet holes drilled from the other
side and become through holes, which you don't want. To prevent
this, offset the two lines of holes. E.g. on one side, make the holes
1" from the front, and on the other, make them 1-1/4". This way,
the holes don't meet, and you'll never notice the offset.
--
-Ed Falk, [email protected]
http://thespamdiaries.blogspot.com/
Edward A. Falk wrote:
> In article<[email protected]>,
> HeyBub<[email protected]> wrote:
>> Of the technique for boring equally-spaced holes in boards that will be the
>> sides of a bookshelf, for the little posts that hold up the shelves.
>
> Here's what I did: I made a wooden strip about three feet long, and
> very carefully pounded nails through it at precise 1.5" intervals
> so that just their tips stuck out the other side.
>
> Then, whenever I want to make a line of holes, I place the wooden
> strip where I want the holes to be, and press it down until all the
> nail tips leave good dimples in my workpiece. Then I use the
> drill press to drill out all the holes.
I think this consistent with my earlier suggestion. In practice, I'm
not yet convinced that a well-centered nail hole or dimple is a lot
better than a pencil mark. A 3/4" template permits you to drill with
confidence. Some good suggestions below!
Bill (i.e. what do I know?)
>
> A couple more tips: Don't drill the holes all the way through; it's
> unsightly. If the bookshelf has more than one vertical compartment,
> the vertical board between compartments becomes a problem -- holes
> drilled on one side will likely meet holes drilled from the other
> side and become through holes, which you don't want. To prevent
> this, offset the two lines of holes. E.g. on one side, make the holes
> 1" from the front, and on the other, make them 1-1/4". This way,
> the holes don't meet, and you'll never notice the offset.
>
On 12/1/11 7:56 PM, Han wrote:
> "Lew Hodgett"<[email protected]> wrote in news:4ed81b81$0$8602
> [email protected]:
>
>> "Lee Michaels" wrote:
>>
>>> Simplest, fastest, cheapest method is to just use some pegboard.
>> -----------------------------------
>> Life is too short to waste it.
>>
>> http://tinyurl.com/7rde2kt
>>
>> Best $25 you will ever invest.
>>
>> Lew
>
> Indeed. Clamp the jig securely or else ... DAMHIKT
>
Clamp? Why? The index pin holds it in the last hole drilled and
drilling takes only one hand.
I hold it with the other hand, just like the picture in the link.
Of course, unclogging that bit takes both hands. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 12/1/11 8:50 PM, Mike O. wrote:
> On 02 Dec 2011 01:56:02 GMT, Han<[email protected]> wrote:
>
>
>> Indeed. Clamp the jig securely or else ... DAMHIKT
>
>
> We drilled a small hole at each end for a 4d nail to hold it in place.
>
> Mike
Why don't you guys just hold it in place like in the picture?
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 12/3/11 10:30 PM, WW wrote:
> "-MIKE-"<[email protected]> wrote in message
> news:[email protected]...
>> On 12/1/11 6:27 PM, Lew Hodgett wrote:
>>> "Lee Michaels" wrote:
>>>
>>>> Simplest, fastest, cheapest method is to just use some pegboard.
>>> -----------------------------------
>>> Life is too short to waste it.
>>>
>>> http://tinyurl.com/7rde2kt
>>>
>>> Best $25 you will ever invest.
>>>
>>> Lew
>>>
>>
>> Someday they will make those bits so they don't clog every 4th hole. :-)
>>
>>
>> --
>>
>> -MIKE-
>
> Mike.... Thats the way to go. I have used one for a couple years. Will never
> part with it. WW
>>
>
I have one.... two, no wait, three... and they all clog every few holes
to the point where the spring-bushing sticks in the depressed position,
so you have to stop and hold the housing while you spin the bit,
dislodging the clogged debris. It's very, very f-n annoying and
frustrating.
I'm not saying I'd go back to using no guide, but it sure would be nice
if they'd modify the bit to expel the debris better. If there's a better
3rd party bit that fit the guide, I'm all ears.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 12/1/2011 5:43 PM, HeyBub wrote:
> Of the technique for boring equally-spaced holes in boards that will be the
> sides of a bookshelf, for the little posts that hold up the shelves.
>
> I'll be using a drill press.
Simply mark the shelf sides where you want the pins, transfer the marks
with a square to the other side of the shelf. Set your fence on the DP
to the distance you want from the edge, put a mark on the DP fence and
align the marks on the fence to the mark on the shelf sides and drill
away. The pins will be perfect every time and easier than fussing
around with peg board, jigs and all that rot.
--
Jack
Add Life to your Days not Days to your Life.
http://jbstein.com
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> On 12/1/11 6:27 PM, Lew Hodgett wrote:
>> "Lee Michaels" wrote:
>>
>>> Simplest, fastest, cheapest method is to just use some pegboard.
>> -----------------------------------
>> Life is too short to waste it.
>>
>> http://tinyurl.com/7rde2kt
>>
>> Best $25 you will ever invest.
>>
>> Lew
>>
>
> Someday they will make those bits so they don't clog every 4th hole. :-)
>
>
> --
>
> -MIKE-
Mike.... Thats the way to go. I have used one for a couple years. Will never
part with it. WW
>