Harbor Freight bandsaw assembly (motor plate)

Wayne Whitney wrote:

> Hello,
>
> I'm assembling the HF 32208 4-speed bandsaw and have a quick question
> on the motor plate orientation. Looking at the stand from the side
> with the power switch, is the high end of the motor plate on the left
> or on the right?
>
> Thanks, Wayne
>
> P.S. Will a Herc-U-Lift fit on the bandsaw stand?
>
> P.P.S. The 4 speeds are 600, 1140, 1670, & 2670 FPM. For cutting
> wood, should I always use the 2670 FPM speed?


The high end of the motor plate goes toward the switch. This means that you
are on the side away from the table when you make your adjustments.

Set it for the highest speed (motor smallest, transfer pulley largest from
motor and smallest to the drive wheel. Keep the belts tight and it works
like a charm.

I had it set up backwards, until the light went on. Wondered why it
wouldn't cut anything. DUH!!!


Deb

hello,

I can not tell you as I do not have the saw next to me, but as you have the
saw now, do yourself a favor and buy the following:

6" raiser kit ($50)
bearing blocks ($12)

well worth the money...

ho, and also, make a new clearance plate to replace the existing flimsy
plastic one...

and then buy a good blade and you will be set....

cyrille


"Wayne Whitney" <[email protected]> wrote in message
news:[email protected]...
> Hello,
>
> I'm assembling the HF 32208 4-speed bandsaw and have a quick question
> on the motor plate orientation. Looking at the stand from the side
> with the power switch, is the high end of the motor plate on the left
> or on the right?
>
> Thanks, Wayne
>
> P.S. Will a Herc-U-Lift fit on the bandsaw stand?
>
> P.P.S. The 4 speeds are 600, 1140, 1670, & 2670 FPM. For cutting
> wood, should I always use the 2670 FPM speed?
>

I don't remember how I assembled mine, but I don't recall any difficulties
following the manual. I know that doesn't help.

I keep mine on the highest speed. I use a $10 all-welded-steel (like Delta)
mobile base from Homier.

The saw looks ugly, but has performed very well.

"Wayne Whitney" <[email protected]> wrote in message
news:[email protected]...
> Hello,
>
> I'm assembling the HF 32208 4-speed bandsaw and have a quick question
> on the motor plate orientation. Looking at the stand from the side
> with the power switch, is the high end of the motor plate on the left
> or on the right?
>
> Thanks, Wayne
>
> P.S. Will a Herc-U-Lift fit on the bandsaw stand?
>
> P.P.S. The 4 speeds are 600, 1140, 1670, & 2670 FPM. For cutting
> wood, should I always use the 2670 FPM speed?
>

Thanks for the answer. I've been traveling and hadn't checked back in
a while.

Duane

On Sun, 26 Mar 2006 22:53:05 -0500, W Canaday <[email protected]>
wrote:

>On Sat, 25 Mar 2006 20:52:16 -0600, Duane Elliott wrote:
>
>> I know this thread is several months old, but I'm just getting to it...so
>> Are ther raiser kit and bearing blocks Harbor Freight pieces or are they
>> some other brand that happens to work?
>>
>> Thanks
>>
>>
>
>HF brand. They are on the website. I own them and they are a good swap for
>your hard-earned dollars.
>
>The earlier poster is correct ... get a GOOD blade (the saw will handle up
>to 3/4") and ditch the dippy plastic table insert.
>
>Bill

On Sat, 25 Mar 2006 20:52:16 -0600, Duane Elliott wrote:

> I know this thread is several months old, but I'm just getting to it...so
> Are ther raiser kit and bearing blocks Harbor Freight pieces or are they
> some other brand that happens to work?
>
> Thanks
>
>

HF brand. They are on the website. I own them and they are a good swap for
your hard-earned dollars.

The earlier poster is correct ... get a GOOD blade (the saw will handle up
to 3/4") and ditch the dippy plastic table insert.

Bill

I know this thread is several months old, but I'm just getting to
it...so Are ther raiser kit and bearing blocks Harbor Freight pieces
or are they some other brand that happens to work?

Thanks


On Mon, 07 Nov 2005 20:32:37 GMT, "Cyrille de Brébisson"
<[email protected]> wrote:

>hello,
>
>I can not tell you as I do not have the saw next to me, but as you have the
>saw now, do yourself a favor and buy the following:
>
>6" raiser kit ($50)
>bearing blocks ($12)
>
>well worth the money...
>
>ho, and also, make a new clearance plate to replace the existing flimsy
>plastic one...
>
>and then buy a good blade and you will be set....
>
>cyrille
>
>
>"Wayne Whitney" <[email protected]> wrote in message
>news:[email protected]...
>> Hello,
>>
>> I'm assembling the HF 32208 4-speed bandsaw and have a quick question
>> on the motor plate orientation. Looking at the stand from the side
>> with the power switch, is the high end of the motor plate on the left
>> or on the right?
>>
>> Thanks, Wayne
>>
>> P.S. Will a Herc-U-Lift fit on the bandsaw stand?
>>
>> P.P.S. The 4 speeds are 600, 1140, 1670, & 2670 FPM. For cutting
>> wood, should I always use the 2670 FPM speed?
>>
>

On 2005-11-06, Dr. Deb <[email protected]> wrote:

> The high end of the motor plate goes toward the switch. This means
> that you are on the side away from the table when you make your
> adjustments.

Yes, I see now that this is the only way the motor plate bracket will
fit so its hole for the bandsaw line up with the holes for the bandsaw
in the "face plate" of the stand. In fact, there's an updated manual
available at www.harborfreight.com for the 32208 bandsaw that has
better pictures of this.

Oddly, though, when it came time to mount the motor plate to the motor
plate bracket and to the support plate, even though all these pieces
have elongated holes, I had to go opposing extremes on the left-right
adjustment to get the motor plate square to the support plate and the
motor plate bracket. I assume it should be square?

I guess when it is time to put on the v-belt, I'll see if the motor
pulley and the bandsaw pulley are aligned or not. If not, I'll have
to lengthen some of the elongated holes for the motor plate so that
there is some adjustibility.

Thanks, Wayne