All of the blurbs I've read which tell how to deal with bandsaw drift
tell you to just saw a straight line down a straight piece of wood,
stop half-way, and mark the angle on your saw table, and then clamp a
fence on the table to that angle, and you're done.Don't forget to tip
your waitress and drive safe on your way home everybody!
They make it sound as though you've divined the magic angle for your
bandsaw once and for all. I'm surprised they don't tell you to just
paint the drift angle right onto the table. In fact, the only time I've
heard anyone say that drift angle depends on anything, they said that
it depended on the particular blade... and that *all*!
I'm not buying it. So, I gotta ask... in everyone's experience, what of
the following factors will, if changed, change the drift angle of your
bandsaw:
- Blade width
- Blade tension
- Feed rate
- Hardness of the wood
- Thickness of the wood
- Grain of the wood
- Height of the upper guide above the wood.
- Slack in the thrust bearing
I would think that the wood would make a difference, but nobody ever
seems to suggest using a similar wood of similar thickness and grain
when initially finding the drift angle.
So, what about it? Once I find my drift angle, what can I change
without having to go find the angle again. And are there any other
factors I've missed?
- Joe
> I'm not buying it. So, I gotta ask... in everyone's experience, what of
> the following factors will, if changed, change the drift angle of your
> bandsaw:
I had some trouble with my Jet 14" shortly after I bought it. What I
did to correct the drift:
1. Remove blade and clean tires (my saw was pretty new - if tires are
older, replace)
2. Remove guide blocks and sand to a smooth and square edge
3. Install new blade - making sure that blade is centered on tires
4. Check tension setting - my saw seems to cut straighter with a bit
higher tension than specified for the particular blade width
5. Adjust guide blocks - just shy of touching the blade on the sides,
and just behind the teeth
6. Set thrust bearing so that even the slightest pressure on the blade
will cause the bearing to spin.
After doing all of this, the saw cuts pretty much dead on straight.
I'd say the two most important things to look at are centering the
blade on the tire and properly adjusting the guide blocks/bearings.
(assuming the blade is in decent condition)
<[email protected]> wrote in message
snip
>
> I'm not buying it. So, I gotta ask... in everyone's experience, what of
> the following factors will, if changed, change the drift angle of your
> bandsaw:
>
> - Blade width
> - Blade tension
> - Feed rate
> - Hardness of the wood
> - Thickness of the wood
> - Grain of the wood
> - Height of the upper guide above the wood.
> - Slack in the thrust bearing
>
snip
> - Joe
It is the tooth set of the blade that contributes the most to blade drift.
Sharpness will have some influence but the largest contributor is set.
Drift can be overpowered by blade tension and bearing/block adjustments and
the use of other gizmos. But why bother - set the saw tension correctly for
the blade and just adjust for the drift and go back to work!
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com
Hey Chris, you nailed it! I never thought about twist being a result of
the wheels! Thank you!
One thing that has helped me to adjust my saw is turn the wheels by
hand while looking straight down from above on the blade. Watch the
blade leave the upper wheel and travel down through the blocks. I have
found that if I only adjust the blocks from the front, the blade will
actually be "tweaked" just a tiny bit when looking down from the top.
II
Tim Taylor wrote:
> "mac davis" <[email protected]> wrote in message
> news:[email protected]...
> > On 18 Aug 2006 02:47:48 -0700, [email protected] wrote:
> >
> > Others will be more scientific, I'm sure, but in my experience, blade
> > sharpness
> > or lack of is the #1 cause of drift, assuming that the saw is set up
> > correctly..
> >
> > My cheapy Ridgid cuts the same angle with 3/8" or 3/4" blade and only
> > drifts if
> > the blade is dull or not tensioned properly...
> >
> > OTOH, I might have accidently bought the one BS that Ridgid made right..
> > *lol*
>
> Mac, I got it's twin then! Mine's exactly the same way as yours.
I also have the Ridgid, with riser. It's no more cheapie than any
other chaiwanese saw. Yes I still dream of a laguna some day.
Tune it up (Duginske's bandsaw book). I didn't get wheels completely
coplanar - they were close and futzing with washers wasn't worth it.
Biggest improvement. Spend the $ for a good blade. I have a
timberwolf 1/2" 3tpi blade. And, per Timberwolf instructions, low
tension (it happens to be 1/2 turn past the 3/8" mark on my saw). It
cuts "straight enough". What that means is, using the curved fence
(like Duginske suggests), given the relatively slow feed rate (if I
want to rip lumber, I'll use the TS, which is faaaar faster), I can
resaw lumber and it 'cuts the line'. I just resawed many feed of 8/4
cherry for bookmatched cabinet drawers and no wandering or bow or
drift. I've also cut 1/8" veneers, ready for the drum sander, this
way. If I need to cut 1/32" veneers maybe I'll sweat it.
Like others have said, when drift appears, my experience is the blades
are getting dull. I use these blades for rough work like bowl blank
cutting. I use my new blades for furniture work like resawing where
tolerances are more important.
I'd suggest that after you align your saw and get a good blade, you
follow my other hobby's maxim. "Relax. Don't worry. Have a homebrew."
After the power tools are off, of course.
"Swingman" <[email protected]> wrote in message
news:[email protected]...
> Top five:
>
> 1. Blade
> 2. Blade
> 3. Blade
> 4. Blade
> 5. Blade
Yes, indeed! To confirm this try stretching an elastic band between index
finger and thumb and the pressing an edge.
What happens?
Of course the harder you press, the greater the deflection.
Jeff G
--
Jeff Gorman, West Yorkshire, UK
email : Username is amgron
ISP is clara.co.uk
www.amgron.clara.net
[email protected] wrote:
> All of the blurbs I've read which tell how to deal with bandsaw drift
> tell you to just saw a straight line down a straight piece of wood,
> stop half-way, and mark the angle on your saw table, and then clamp a
> fence on the table to that angle, and you're done.Don't forget to tip
> your waitress and drive safe on your way home everybody!
I'm surprised that nobody has pointed out the fact that you can *adjust*
your drift angle.
The tire is crowned, so depending on where the blade rides on the tire
it can be made to angle one way or the other. By adjusting the blade
tracking you can compensate for any drift.
On some scrap, draw a series of straight lines parallel to one of the sides.
Freehand cut a couple inches along the first line then turn off the saw.
This will give you your drift angle.
Now adjust the tracking. Bringing the blade towards the operator will
tend to twist it clockwise.
Now cut a few more inches and check the effect of your adjustment.
A few iterations of this and you should be able to get rid of the drift.
Chris
<[email protected]> wrote in message
news:[email protected]...
> All of the blurbs I've read which tell how to deal with bandsaw drift
> tell you to just saw a straight line down a straight piece of wood,
> stop half-way, and mark the angle on your saw table, and then clamp a
> fence on the table to that angle, and you're done.Don't forget to tip
> your waitress and drive safe on your way home everybody!
>
> They make it sound as though you've divined the magic angle for your
> bandsaw once and for all. I'm surprised they don't tell you to just
> paint the drift angle right onto the table. In fact, the only time I've
> heard anyone say that drift angle depends on anything, they said that
> it depended on the particular blade... and that *all*!
>
> I'm not buying it. So, I gotta ask... in everyone's experience, what of
> the following factors will, if changed, change the drift angle of your
> bandsaw:
>
> - Blade width
> - Blade tension
> - Feed rate
> - Hardness of the wood
> - Thickness of the wood
> - Grain of the wood
> - Height of the upper guide above the wood.
> - Slack in the thrust bearing
>
> I would think that the wood would make a difference, but nobody ever
> seems to suggest using a similar wood of similar thickness and grain
> when initially finding the drift angle.
>
> So, what about it? Once I find my drift angle, what can I change
> without having to go find the angle again. And are there any other
> factors I've missed?
I've got an 18" Jet band saw and haven't experienced this problem. I don't
know it it's inherent to this saw or if I simply have a knack for installing
blades... I don't do anything special while installing blades, it's all done
by eye and feel. I don't have a problem with the Jet brand blades nor with
Timberwolf blades. I haven't tried other brands so I cannot rule out blades
as the problem for others.
John
"John Grossbohlin" <[email protected]> wrote in message
news:[email protected]...
>
> I've got an 18" Jet band saw and haven't experienced this problem. I don't
> know it it's inherent to this saw or if I simply have a knack for
> installing blades... I don't do anything special while installing blades,
> it's all done by eye and feel. I don't have a problem with the Jet brand
> blades nor with Timberwolf blades. I haven't tried other brands so I
> cannot rule out blades as the problem for others.
>
> John
>
>
IMHO the quality of your saw lends a big hand in elimilating many
adjustments that have to be dead on.
<[email protected]> wrote in message
news:[email protected]...
Snip
>
> They make it sound as though you've divined the magic angle for your
> bandsaw once and for all. I'm surprised they don't tell you to just
> paint the drift angle right onto the table. In fact, the only time I've
> heard anyone say that drift angle depends on anything, they said that
> it depended on the particular blade... and that *all*!
I commented on Andy's similar question after you posted this.
When you have your fence set up to compensate for drift on a particular
blade it is set up only for that blade and that tension. Depending on the
sharpness, quality, blade size, and BS tension settings another blade may
require difference fence settings to compensate for drift. Drift can be
caused by the blade or the BS it self.
> I'm not buying it. So, I gotta ask... in everyone's experience, what of
> the following factors will, if changed, change the drift angle of your
> bandsaw:
>
> - Blade width
On my old Craftsman saw, Yes.
On my new Laguna, VERY little to no change.
> - Blade tension
My old saw, Absolutely
My new saw, none so far.
> - Feed rate
Old saw, yes
New saw, no signs yet.
> - Hardness of the wood
Old, I don't recall.
New, no change.
> - Thickness of the wood
Old, yes
New, resawing through 11", No.
> - Grain of the wood
Old, don"t recall.
New, so far with sharp blades, No.
> - Height of the upper guide above the wood.
Old, Yes.
New, makes no difference
> - Slack in the thrust bearing
Old, Yes.
New, No.
>
> I would think that the wood would make a difference, but nobody ever
> seems to suggest using a similar wood of similar thickness and grain
> when initially finding the drift angle.
>
> So, what about it? Once I find my drift angle, what can I change
> without having to go find the angle again.
If you tried everything, perhaps a new saw will be required to remedy the
problem. Remember, a lot of factors come into play that differ with each
blade. IMHO the more rock solid the saw is the less you will have to tweek
blade tension and for each individual blade.
And are there any other
> factors I've missed?
Blade quality? Blade sharpness? Band saw build quality?
"Chris Friesen" <[email protected]> wrote in message
news:[email protected]...
> [email protected] wrote:
>> All of the blurbs I've read which tell how to deal with bandsaw drift
>> tell you to just saw a straight line down a straight piece of wood,
>> stop half-way, and mark the angle on your saw table, and then clamp a
>> fence on the table to that angle, and you're done.Don't forget to tip
>> your waitress and drive safe on your way home everybody!
>
> I'm surprised that nobody has pointed out the fact that you can *adjust*
> your drift angle.
>
> The tire is crowned, so depending on where the blade rides on the tire it
> can be made to angle one way or the other. By adjusting the blade
> tracking you can compensate for any drift.
>
> On some scrap, draw a series of straight lines parallel to one of the
> sides.
>
> Freehand cut a couple inches along the first line then turn off the saw.
> This will give you your drift angle.
>
> Now adjust the tracking. Bringing the blade towards the operator will
> tend to twist it clockwise.
>
> Now cut a few more inches and check the effect of your adjustment.
>
> A few iterations of this and you should be able to get rid of the drift.
>
> Chris
Chris,
You win the cigar. You are absolutely correct.
"Lowell Holmes" <[email protected]> wrote in message
news:XOoFg.1659$u1.1514@trnddc05...
>>
> Chris,
>
> You win the cigar. You are absolutely correct.
>
I am not sure that I agree that this is the only correct way. Keeping mind,
that the crown is there so that the blade will track in the same place. The
blade naturally tries to ride along the highest point of the tire.
Additionally, many band saw tires have very little crown at all.
"Leon" <[email protected]> wrote in message
news:[email protected]...
>
> "Lowell Holmes" <[email protected]> wrote in message
> news:XOoFg.1659$u1.1514@trnddc05...
>>>
>> Chris,
>>
>> You win the cigar. You are absolutely correct.
>>
> I am not sure that I agree that this is the only correct way. Keeping
> mind, that the crown is there so that the blade will track in the same
> place. The blade naturally tries to ride along the highest point of the
> tire. Additionally, many band saw tires have very little crown at all.
That's how it works on my Jet though. Also, at least three different
articles I've read say the same thing.
"mac davis" <[email protected]> wrote in message
news:[email protected]...
> On 18 Aug 2006 02:47:48 -0700, [email protected] wrote:
>
> Others will be more scientific, I'm sure, but in my experience, blade
> sharpness
> or lack of is the #1 cause of drift, assuming that the saw is set up
> correctly..
>
> My cheapy Ridgid cuts the same angle with 3/8" or 3/4" blade and only
> drifts if
> the blade is dull or not tensioned properly...
>
> OTOH, I might have accidently bought the one BS that Ridgid made right..
> *lol*
Mac, I got it's twin then! Mine's exactly the same way as yours.
On Fri, 18 Aug 2006 10:55:06 -0600, Chris Friesen <[email protected]> wrote:
>[email protected] wrote:
>> All of the blurbs I've read which tell how to deal with bandsaw drift
>> tell you to just saw a straight line down a straight piece of wood,
>> stop half-way, and mark the angle on your saw table, and then clamp a
>> fence on the table to that angle, and you're done.Don't forget to tip
>> your waitress and drive safe on your way home everybody!
>
>I'm surprised that nobody has pointed out the fact that you can *adjust*
>your drift angle.
>
>The tire is crowned, so depending on where the blade rides on the tire
>it can be made to angle one way or the other. By adjusting the blade
>tracking you can compensate for any drift.
>
>On some scrap, draw a series of straight lines parallel to one of the sides.
>
>Freehand cut a couple inches along the first line then turn off the saw.
> This will give you your drift angle.
>
>Now adjust the tracking. Bringing the blade towards the operator will
>tend to twist it clockwise.
>
>Now cut a few more inches and check the effect of your adjustment.
>
>A few iterations of this and you should be able to get rid of the drift.
>
>Chris
welcome to the world of proper tracking.. *g*
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
"Lowell Holmes" <[email protected]> wrote in message
news:fftFg.15409$uV.6185@trnddc08...
>
> "Leon" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "Lowell Holmes" <[email protected]> wrote in message
>> news:XOoFg.1659$u1.1514@trnddc05...
>>>>
>>> Chris,
>>>
>>> You win the cigar. You are absolutely correct.
>>>
>> I am not sure that I agree that this is the only correct way. Keeping
>> mind, that the crown is there so that the blade will track in the same
>> place. The blade naturally tries to ride along the highest point of the
>> tire. Additionally, many band saw tires have very little crown at all.
> That's how it works on my Jet though. Also, at least three different
> articles I've read say the same thing.
>
>
I am not saying that it will not work, just that it may not be absolutely
correct. ;~)
On 18 Aug 2006 02:47:48 -0700, [email protected] wrote:
Others will be more scientific, I'm sure, but in my experience, blade sharpness
or lack of is the #1 cause of drift, assuming that the saw is set up correctly..
My cheapy Ridgid cuts the same angle with 3/8" or 3/4" blade and only drifts if
the blade is dull or not tensioned properly...
OTOH, I might have accidently bought the one BS that Ridgid made right.. *lol*
>All of the blurbs I've read which tell how to deal with bandsaw drift
>tell you to just saw a straight line down a straight piece of wood,
>stop half-way, and mark the angle on your saw table, and then clamp a
>fence on the table to that angle, and you're done.Don't forget to tip
>your waitress and drive safe on your way home everybody!
>
>They make it sound as though you've divined the magic angle for your
>bandsaw once and for all. I'm surprised they don't tell you to just
>paint the drift angle right onto the table. In fact, the only time I've
>heard anyone say that drift angle depends on anything, they said that
>it depended on the particular blade... and that *all*!
>
>I'm not buying it. So, I gotta ask... in everyone's experience, what of
>the following factors will, if changed, change the drift angle of your
>bandsaw:
>
> - Blade width
> - Blade tension
> - Feed rate
> - Hardness of the wood
> - Thickness of the wood
> - Grain of the wood
> - Height of the upper guide above the wood.
> - Slack in the thrust bearing
>
>I would think that the wood would make a difference, but nobody ever
>seems to suggest using a similar wood of similar thickness and grain
>when initially finding the drift angle.
>
>So, what about it? Once I find my drift angle, what can I change
>without having to go find the angle again. And are there any other
>factors I've missed?
>
>- Joe
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm