Hello all,
My home shop is in a detached 2-car garage, which currently has ZERO
cars in it (minor gloat!), but at most will have just 1 car. Plus, the
garage is an extra 6-8ft. deep and wide over a "standard" 2-car.
DC is high on my priority list, and I'm researching that now. BUT in
addition, my thinking is that I can *supplement* the cleaning of the
air by adding a gable ventilation fan to the garage, e.g. the Broan 353
Gable Fan.
My question: will the life expectancy of these types of fans be
seriously shortened in this application? I'm thinking of the (higher
than normal) amount of airborne dust that will be passing past the
motor.
Any feedback is appreciated.
-Chris
If you are doing a good job of dust collecting at the source then the
gable vent is not going to see much dust.
"TheNewGuy" <[email protected]> wrote:
>Hello all,
>
>My home shop is in a detached 2-car garage, which currently has ZERO
>cars in it (minor gloat!), but at most will have just 1 car. Plus, the
>garage is an extra 6-8ft. deep and wide over a "standard" 2-car.
>
>DC is high on my priority list, and I'm researching that now. BUT in
>addition, my thinking is that I can *supplement* the cleaning of the
>air by adding a gable ventilation fan to the garage, e.g. the Broan 353
>Gable Fan.
>
>My question: will the life expectancy of these types of fans be
>seriously shortened in this application? I'm thinking of the (higher
>than normal) amount of airborne dust that will be passing past the
>motor.
>
>Any feedback is appreciated.
>
>-Chris
Jim B.
Thanks for the reply, Jim.
My thought is that the gable fan would obviate the need for an ambient
air filter/scrubber. Even with the best collection at the machines I
have, from what I've read sofar, there could still be some v.fine dust
in the air. In particular: how much sanding do I do, and how well can
I collect the sanding dust? Is my DC unit closeted (not planned to be
right now)? And I'm still looking for a good way to hookup a chopsaw
to the DC to capture max dust.
So, if the gable fan can refresh the air in my shop every... 10-12
minutes? I gotta think that's at least as good a benefit as an ambient
air filter. 'Course, in the wintertime... :*)
Anyway, I'm gonna install it also for the heat exhaust reasons it's
designed for (Sierra foothills toasty summers); I'll just have to check
it now and then to see if it's accumulating much dust.
-Chris
Jim Behning wrote:
> If you are doing a good job of dust collecting at the source then the
> gable vent is not going to see much dust.
>
If you were worried about it you could build a frame around it that
takes at least 4 24x24 white furnace filters. Not the 99 cent ones but
some better ones. I mentioned at least 4 filters because you do not
want the air flow restricted too much by some small filter area.
"TheNewGuy" <[email protected]> wrote:
>Thanks for the reply, Jim.
>
>My thought is that the gable fan would obviate the need for an ambient
>air filter/scrubber. Even with the best collection at the machines I
>have, from what I've read sofar, there could still be some v.fine dust
>in the air. In particular: how much sanding do I do, and how well can
>I collect the sanding dust? Is my DC unit closeted (not planned to be
>right now)? And I'm still looking for a good way to hookup a chopsaw
>to the DC to capture max dust.
>
>So, if the gable fan can refresh the air in my shop every... 10-12
>minutes? I gotta think that's at least as good a benefit as an ambient
>air filter. 'Course, in the wintertime... :*)
>
>Anyway, I'm gonna install it also for the heat exhaust reasons it's
>designed for (Sierra foothills toasty summers); I'll just have to check
>it now and then to see if it's accumulating much dust.
>
>-Chris
>
>
>Jim Behning wrote:
>> If you are doing a good job of dust collecting at the source then the
>> gable vent is not going to see much dust.
>>
Jim B.