The3rd Earl Of Derby (in
[email protected]) said:
| Why is the wood scorching when I attempt to cut across the grain
| and I'm doing fine going with the grain?
Scorching is caused by an overheated bit. Bits overheat when they're
dull and when they're fed at a speed that doesn't remove enough chips
fast enough to carry the heat away.
Make sure your bits are sharp and that your feed speed is adequate.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto
The3rd Earl Of Derby wrote:
> The3rd Earl Of Derby wrote:
>> Hello
>> Why is the wood scorching when I attempt to cut across the grain and
>> I'm doing fine going with the grain?
>>
>> Wood is pine.
>>
>> Thank you.
>
> Thanks all for replies.
>
> I got a piece of advice,but havn't tried it yet but it sounds feasible?
> the advice was to wet the the wood a bit(damp) and then route across the
> grain and a light sanding when dry.
>
You really shouldn't be scorching with pine. You should make sure (as
already mentioned) that your bit is sharp, that you're not cutting off too
much at once (1/16" at a time?), and that you're not moving too slowly.
--
Michael White "To protect people from the effects of folly is to
fill the world with fools." -Herbert Spencer
The3rd Earl Of Derby wrote:
> Hello
> Why is the wood scorching when I attempt to cut across the grain and
> I'm doing fine going with the grain?
>
> Wood is pine.
>
> Thank you.
Thanks all for replies.
I got a piece of advice,but havn't tried it yet but it sounds feasible?
the advice was to wet the the wood a bit(damp) and then route across the
grain and a light sanding when dry.
--
Sir Benjamin Middlethwaite
"The3rd Earl Of Derby" wrote in
> Why is the wood scorching when I attempt to cut across the grain and I'm
> doing fine going with the grain?
>
> Wood is pine.
Take more passes with lighter cuts, and try moving the router faster.
Router burn can be difficult to remove on some woods. The easiest way is to
take a light cut for the last pass, removing any previous burn marks.
--
www.e-woodshop.net
Last update: 7/30/06
RonB wrote:
> End grain is a little more susceptible to burning. One remedy is
> to make first pass a little shallow and then a final cut at desired
> depth. If not practical because of matching adjoining sides, just
> try a second quicker pass at same depth.
And if you still get scorching, use the router bit as a scraper
(manually)
> Then the sanding.
dadiOH
_______________
> "The3rd Earl Of Derby" <[email protected]> wrote in message
> news:[email protected]...
>> Hello
>> Why is the wood scorching when I attempt to cut across the grain
>> and I'm doing fine going with the grain?
>>
>> Wood is pine.
>>
>> Thank you.
>>
>> --
>> Sir Benjamin Middlethwaite
Might try taking lighter cuts and, if possible, move the router through the
cut a little faster.
"The3rd Earl Of Derby" <[email protected]> wrote in message
news:[email protected]...
> The3rd Earl Of Derby wrote:
>> Hello
>> Why is the wood scorching when I attempt to cut across the grain and
>> I'm doing fine going with the grain?
>>
>> Wood is pine.
>>
>> Thank you.
>
> Thanks all for replies.
>
> I got a piece of advice,but havn't tried it yet but it sounds feasible?
> the advice was to wet the the wood a bit(damp) and then route across the
> grain and a light sanding when dry.
>
> --
> Sir Benjamin Middlethwaite
>
>
>
End grain is a little more susceptible to burning. One remedy is to make
first pass a little shallow and then a final cut at desired depth. If not
practical because of matching adjoining sides, just try a second quicker
pass at same depth. Then the sanding.
RonB
"The3rd Earl Of Derby" <[email protected]> wrote in message
news:[email protected]...
> Hello
> Why is the wood scorching when I attempt to cut across the grain and I'm
> doing fine going with the grain?
>
> Wood is pine.
>
> Thank you.
>
> --
> Sir Benjamin Middlethwaite
>
>