"[email protected]" wrote:
> Number One son has drafted me for a bathroom renovation, which may
> involve installing a glass block partial wall. The rub is that he
> wants it flush against his sloped ceiling. Is it possible to cut
> glass blocks accurately and cleanly? Any tips will be appreciated.
-------------------------------------
Glass shops do some interesting things with water jet technology and
CNC control.
Might want to talk to one for some guidance.
Lew
On Jan 10, 9:09=A0pm, "[email protected]" <[email protected]> wrote:
> Number One son has drafted me for a bathroom renovation, which may
> involve installing a glass block partial wall. =A0The rub is that he want=
s
> it flush against his sloped ceiling. =A0Is it possible to cut glass block=
s
> accurately and cleanly? =A0Any tips will be appreciated.
>
> Larry
For interior use, the acrylic blocks are a good choice. they can
easily be cut.
Glass blocks are never cut.. not that I have ever seen.
On Jan 10, 9:09=A0pm, "[email protected]" <[email protected]> wrote:
> Number One son has drafted me for a bathroom renovation, which may
> involve installing a glass block partial wall. =A0The rub is that he want=
s
> it flush against his sloped ceiling. =A0Is it possible to cut glass block=
s
> accurately and cleanly? =A0Any tips will be appreciated.
>
> Larry
As a follow up, I just happen to be talking to a block guy and I
thought to ask him.
If you absolutely MUST, do acrylics. If not, redesign. Cut glass
blocks have all the problems Mr Dingley so aptly pointed out.
Condensation and cracking.
On 1/11/10 12:02 AM, Robatoy wrote:
> On Jan 10, 9:09 pm, "[email protected]"<[email protected]> wrote:
>> Number One son has drafted me for a bathroom renovation, which may
>> involve installing a glass block partial wall. The rub is that he wants
>> it flush against his sloped ceiling. Is it possible to cut glass blocks
>> accurately and cleanly? Any tips will be appreciated.
>>
>> Larry
>
> For interior use, the acrylic blocks are a good choice. they can
> easily be cut.
>
> Glass blocks are never cut.. not that I have ever seen.
How about using the acrylic blocks, just where the cuts need to be made,
assuming you can get some with a similar enough appearance.
Just an idle thought. At the ceiling the difference should be less
noticeable, and if you like the appearance of the glass enough to offset
the disparity.
--
Froz...
The system will be down for 10 days for preventive maintenance.
On 11 Jan, 02:09, "[email protected]" <[email protected]> wrote:
> Is it possible to cut glass blocks accurately and cleanly?
Yes. Either water jet (easy, costs a little) or else a wet wheel tile
cutter, and you'll lose a few.
Don't be surprised if some of them spontaneously crack a few days
after cutting.
On the whole I'd avoid this. You need to seal the insides of glass
blocks very carefully around bathrooms, otherwise you get condensation
problems. Pragmatically I'd probably redesign until I could use full &
half blocks, without cutting.
Robatoy wrote:
> On Jan 10, 9:09 pm, "[email protected]" <[email protected]> wrote:
>> Number One son has drafted me for a bathroom renovation, which may
>> involve installing a glass block partial wall. The rub is that he
>> wants it flush against his sloped ceiling. Is it possible to cut
>> glass blocks accurately and cleanly? Any tips will be appreciated.
>>
>> Larry
>
> For interior use, the acrylic blocks are a good choice. they can
> easily be cut.
>
> Glass blocks are never cut.. not that I have ever seen.
i've never seen them cut and installed either, but a tile saw will go
through one pretty quickly.
you can get 1/2 height blocks. i've also made a glass block out of stained
glass and used that in a non-standard height place, or perhaps you can make
a wood block and use it as a base or fill block on the top (obwwr)?
On Mon, 11 Jan 2010 09:56:17 -0700, "charlie"
<[email protected]> wrote:
>Robatoy wrote:
>> On Jan 10, 9:09 pm, "[email protected]" <[email protected]> wrote:
>>> Number One son has drafted me for a bathroom renovation, which may
>>> involve installing a glass block partial wall. The rub is that he
>>> wants it flush against his sloped ceiling. Is it possible to cut
>>> glass blocks accurately and cleanly? Any tips will be appreciated.
>>>
>>> Larry
>>
>> For interior use, the acrylic blocks are a good choice. they can
>> easily be cut.
>>
>> Glass blocks are never cut.. not that I have ever seen.
>
>i've never seen them cut and installed either, but a tile saw will go
>through one pretty quickly.
...I just did a kitchen and lady selected glass tile sheets for her
splash...I went to the local marble/stone house and there on the wall
was "glass blades"...bought one, installed on my wet saw, and she cut
sweet as can be. Would have no qualms cutting some glass blocks.
OTOH, is the ceiling sloped? If not, why not construct a "base" out
of whatever material would complement the glass and set the blocks on
*it?* Then you could figger the measures, block and grout, to come
out with a grout line on top...
cg
>
>you can get 1/2 height blocks. i've also made a glass block out of stained
>glass and used that in a non-standard height place, or perhaps you can make
>a wood block and use it as a base or fill block on the top (obwwr)?
>