Corian question

If you have to do it, don't use spent blades; use nice sharp ones. Think
about it; if the material is particularly tough, do you want to go at it
with dull blades?

I have a pile of 1/2" corian blanks I picked up for nothing at an auction.
(Guy bought an enormous pile of blanks and sheets for $100. He told me to
take what I wanted since he didn't know how he was going to get it home
anyhow, so I took 3 nice sheets and 10 blanks.) Never thought of using them
for zcis. Certainly more stable than wood...

If you do, don't cut them to length until you've reached final
thickness, as they'll be too short for a safe passage through the
planer. Let us know how it turns out, eh? Tom

On Sun, 25 Sep 2005 09:51:51 -0400, "Sidney"
<don'tcalluswe'[email protected]> wrote:

>I have rough cut 8 Corian blanks for TS ZC inserts. Problem is, I need
>them less than 1/2" thick. My idea is to run them through my planer
>(Delta 22-580) taking very light passes with the spent blades that are
>currently installed, then flip the double-edge blades afterward.
>
>Is it a bad idea to run Corian through a planer? Could it damage the
>planer, the blades, or me? Anyone done this? TIA for any advice.
>
>Sidney


I wouldn't use Corian for an insert.

It can crack and send sharp stuff heading your way.


Tom Watson - WoodDorker
tjwatson1ATcomcastDOTnet (email)
http://home.comcast.net/~tjwatson1/ (website)

Hey, thanks for all the great advice. I only need to take off about
1/16", so I'll go with Robatoy's suggestion and rabbet the edges. I
can easily do this with a staight bit in my router table w/ fence. It
makes more sense to cut Corian with carbide anyway. Thanks again, all.

Sid

> I wouldn't use Corian for an insert.
>
> It can crack and send sharp stuff heading your way.
>
Thanks, I was tempted to try it myself, but questioned it brittleness.

Tom Watson wrote:

> On Sun, 25 Sep 2005 09:51:51 -0400, "Sidney"
> <don'tcalluswe'[email protected]> wrote:
>
> > I have rough cut 8 Corian blanks for TS ZC inserts. Problem is, I
> > need them less than 1/2" thick. My idea is to run them through my
> > planer (Delta 22-580) taking very light passes with the spent
> > blades that are currently installed, then flip the double-edge
> > blades afterward.
> >
> > Is it a bad idea to run Corian through a planer? Could it damage
> > the planer, the blades, or me? Anyone done this? TIA for any
> > advice.
> >
> > Sidney
>
>
> I wouldn't use Corian for an insert.
>
> It can crack and send sharp stuff heading your way.
>
>
> Tom Watson - WoodDorker
> tjwatson1ATcomcastDOTnet (email)
> http://home.comcast.net/~tjwatson1/ (website)

Tom,

The brittleness problem hadn't occurred to me. Thanks for the reality
check. Time to go to plan B.

Sid

In article <[email protected]>,
Robatoy <[email protected]> wrote:

> In article <[email protected]>,
> "Sidney" <don'tcalluswe'[email protected]> wrote:
>
> > Hey, thanks for all the great advice. I only need to take off about
> > 1/16", so I'll go with Robatoy's suggestion and rabbet the edges. I
> > can easily do this with a staight bit in my router table w/ fence. It
> > makes more sense to cut Corian with carbide anyway. Thanks again, all.
> >
> > Sid
>
> Oh, and before I forget, make sure the edges are sanded smooth so there
> won't be any fissures from sawblades, etc where cracks can start.


Upon further reflection:


It may therefore be wise to terminate the slot that you'll be cutting
with your sawblade, with a drilled hole (1/4"?) on each end of the slot
as a stress-relief, in order to prevent cracks from developing there.
Kinda like: 0==============0

In article <[email protected]>,
"Sidney" <don'tcalluswe'[email protected]> wrote:

> I have rough cut 8 Corian blanks for TS ZC inserts. Problem is, I need
> them less than 1/2" thick. My idea is to run them through my planer
> (Delta 22-580) taking very light passes with the spent blades that are
> currently installed, then flip the double-edge blades afterward.
>
> Is it a bad idea to run Corian through a planer? Could it damage the
> planer, the blades, or me? Anyone done this? TIA for any advice.
>
> Sidney

Use them full thickness, but rabbet the edges down to the required size.
If your arbor won't drop down enough for your sawblade to clear to cut
the new insert, start the zc cut with an 8" or 7 1/4" blade.

IF you're going to put them through the planer, make sure the blades are
sharp. Should the piece of Corian decide to break up in the planer, it
can/will cause lots of damage. It is not recommended.

In article <[email protected]>,
"Sidney" <don'tcalluswe'[email protected]> wrote:

> Hey, thanks for all the great advice. I only need to take off about
> 1/16", so I'll go with Robatoy's suggestion and rabbet the edges. I
> can easily do this with a staight bit in my router table w/ fence. It
> makes more sense to cut Corian with carbide anyway. Thanks again, all.
>
> Sid

Oh, and before I forget, make sure the edges are sanded smooth so there
won't be any fissures from sawblades, etc where cracks can start.

In article <[email protected]>,
Tom Watson <[email protected]> wrote:


> I wouldn't use Corian for an insert.
>
> It can crack and send sharp stuff heading your way.
>
One can't be too careful.

Even though Corian is pretty tough stuff, that possibility does exist.

I use Baltic birch ply fore my ZCI.

How much do you need to thin them down? It might be better to use a belt
sander.

Lee

--
To e-mail, replace "bucketofspam" with "dleegordon"

_________________________________
Lee Gordon
http://www.leegordonproductions.com